6 First, disable kernel IP forward in *csp2s22c03* to ensure the host cannot use
7 kernel forwarding (all the settings in *net2s22c05* and *csp2s22c04* remain unchanged):
9 .. code-block:: console
11 csp2s22c03$ echo 0 | sudo tee /proc/sys/net/ipv4/ip_forward
13 csp2s22c03$ sysctl net.ipv4.ip_forward
14 net.ipv4.ip_forward = 0
16 You can use DPDK’s device binding utility (./install-vpp-native/dpdk/sbin/dpdk-devbind)
17 to list network devices and bind/unbind them from specific drivers. The flag “-s/--status”
18 shows the status of devices; the flag “-b/--bind” selects the driver to bind. The
19 status of devices in our system indicates that the two 40-GbE XL710 devices are located
20 at 82:00.0 and 82:00.1. Use the device’s slots to bind them to the driver uio_pci_generic:
22 .. code-block:: console
24 csp2s22c03$ ./install-vpp-native/dpdk/sbin/dpdk-devbind -s
26 Network devices using DPDK-compatible driver
27 ============================================
30 Network devices using kernel driver
31 ===================================
32 0000:03:00.0 'Ethernet Controller 10-Gigabit X540-AT2' if=enp3s0f0 drv=ixgbe unused=vfio-pci,uio_pci_generic *Active*
33 0000:03:00.1 'Ethernet Controller 10-Gigabit X540-AT2' if=enp3s0f1 drv=ixgbe unused=vfio-pci,uio_pci_generic *Active*
34 0000:82:00.0 'Ethernet Controller XL710 for 40GbE QSFP+' if=ens802f0d1,ens802f0 drv=i40e unused=uio_pci_generic
35 0000:82:00.1 'Ethernet Controller XL710 for 40GbE QSFP+' if=ens802f1d1,ens802f1 drv=i40e unused=uio_pci_generic
41 csp2s22c03$ sudo modprobe uio_pci_generic
42 csp2s22c03$ sudo ./install-vpp-native/dpdk/sbin/dpdk-devbind --bind uio_pci_generic 82:00.0
43 csp2s22c03$ sudo ./install-vpp-native/dpdk/sbin/dpdk-devbind --bind uio_pci_generic 82:00.1
45 csp2s22c03$ sudo ./install-vpp-native/dpdk/sbin/dpdk-devbind -s
47 Network devices using DPDK-compatible driver
48 ============================================
49 0000:82:00.0 'Ethernet Controller XL710 for 40GbE QSFP+' drv=uio_pci_generic unused=i40e,vfio-pci
50 0000:82:00.1 'Ethernet Controller XL710 for 40GbE QSFP+' drv=uio_pci_generic unused=i40e,vfio-pci
52 Network devices using kernel driver
53 ===================================
54 0000:03:00.0 'Ethernet Controller 10-Gigabit X540-AT2' if=enp3s0f0 drv=ixgbe unused=vfio-pci,uio_pci_generic *Active*
55 0000:03:00.1 'Ethernet Controller 10-Gigabit X540-AT2' if=enp3s0f1 drv=ixgbe unused=vfio-pci,uio_pci_generic *Active*
57 Start the VPP service, and verify that VPP is running:
59 .. code-block:: console
61 csp2s22c03$ sudo service vpp start
62 csp2s22c03$ ps -ef | grep vpp
63 root 105655 1 98 17:34 ? 00:00:02 /usr/bin/vpp -c /etc/vpp/startup.conf
65 105675 105512 0 17:34 pts/4 00:00:00 grep --color=auto vpp
67 To access the VPP CLI, issue the command sudo vppctl . From the VPP interface, list
68 all interfaces that are bound to DPDK using the command show interface:
70 VPP shows that the two 40-Gbps ports located at 82:0:0 and 82:0:1 are bound. Next,
71 you need to assign IP addresses to those interfaces, bring them up, and verify:
73 .. code-block:: console
75 vpp# set interface ip address FortyGigabitEthernet82/0/0 10.10.1.1/24
76 vpp# set interface ip address FortyGigabitEthernet82/0/1 10.10.2.1/24
77 vpp# set interface state FortyGigabitEthernet82/0/0 up
78 vpp# set interface state FortyGigabitEthernet82/0/1 up
79 vpp# show interface address
80 FortyGigabitEthernet82/0/0 (up):
82 FortyGigabitEthernet82/0/1 (up):
86 At this point VPP is operational. You can ping these interfaces either from *net2s22c05*
87 or *csp2s22c04*. Moreover, VPP can forward packets whose IP address are 10.10.1.0/24 and
88 10.10.2.0/24, so you can ping between *net2s22c05* and *csp2s22c04*. Also, you can
89 run iperf3 as illustrated in the previous example, and the result from running iperf3
90 between *net2s22c05* and *csp2s22c04* increases to 20.3 Gbits per second.
92 .. code-block:: console
94 ET2S22C05$ iperf3 -c 10.10.1.2
95 Connecting to host 10.10.1.2, port 5201
96 [ 4] local 10.10.2.2 port 54078 connected to 10.10.1.2 port 5201
97 [ ID] Interval Transfer Bandwidth Retr Cwnd
98 [ 4] 0.00-1.00 sec 2.02 GBytes 17.4 Gbits/sec 460 1.01 MBytes
99 [ 4] 1.00-2.00 sec 3.28 GBytes 28.2 Gbits/sec 0 1.53 MBytes
100 [ 4] 2.00-3.00 sec 2.38 GBytes 20.4 Gbits/sec 486 693 KBytes
101 [ 4] 3.00-4.00 sec 2.06 GBytes 17.7 Gbits/sec 1099 816 KBytes
102 [ 4] 4.00-5.00 sec 2.07 GBytes 17.8 Gbits/sec 614 1.04 MBytes
103 [ 4] 5.00-6.00 sec 2.25 GBytes 19.3 Gbits/sec 2869 716 KBytes
104 [ 4] 6.00-7.00 sec 2.26 GBytes 19.4 Gbits/sec 3321 683 KBytes
105 [ 4] 7.00-8.00 sec 2.33 GBytes 20.0 Gbits/sec 2322 594 KBytes
106 [ 4] 8.00-9.00 sec 2.28 GBytes 19.6 Gbits/sec 1690 1.23 MBytes
107 [ 4] 9.00-10.00 sec 2.73 GBytes 23.5 Gbits/sec 573 680 KBytes
108 - - - - - - - - - - - - - - - - - - - - - - - - -
109 [ ID] Interval Transfer Bandwidth Retr
110 [ 4] 0.00-10.00 sec 23.7 GBytes 20.3 Gbits/sec 13434 sender
111 [ 4] 0.00-10.00 sec 23.7 GBytes 20.3 Gbits/sec receiver
115 The **show run** command displays the graph runtime statistics. Observe that the
116 average vector per node is 6.76, which means on average, a vector of 6.76 packets
117 is handled in a graph node.
119 .. figure:: /_images/build-a-fast-network-stack-terminal.png