1 # Copyright (c) 2021 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
6 # http://www.apache.org/licenses/LICENSE-2.0
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
15 | Resource | resources/libraries/robot/shared/default.robot
16 | Resource | resources/libraries/robot/overlay/lisp.robot
18 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
20 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
21 | ... | NIC_Intel-X710 | IP6FWD | ENCAP | LISP | IP4UNRLAY | IP6OVRLAY
23 | ... | RXQ_SIZE_0 | TXQ_SIZE_0
24 | ... | ethip6lispip4-ip6base
26 | Suite Setup | Setup suite topology interfaces | performance
27 | Suite Teardown | Tear down suite | performance
28 | Test Setup | Setup test | performance
29 | Test Teardown | Tear down test | performance
31 | Test Template | Local Template
33 | Documentation | **RFC6830: Pkt throughput Lisp test cases**
35 | ... | - **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular \
36 | ... | topology with single links between nodes. \
38 | ... | - **[Enc] Packet Encapsulations:** Eth-IPv6-LISP-IPv4 on DUT1-DUT2, \
39 | ... | Eth-IPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel. \
41 | ... | - **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 \
42 | ... | routing and static routes. LISPoIPv4 tunnel is configured between \
43 | ... | DUT1 and DUT2. DUT1 and DUT2 tested with ${nic_name}.
45 | ... | - **[Ver] TG verification:** TG finds and reports throughput NDR (Non \
46 | ... | Drop Rate) with zero packet loss tolerance and throughput PDR \
47 | ... | (Partial Drop Rate) with non-zero packet loss tolerance (LT) \
48 | ... | expressed in percentage of packets transmitted. NDR and PDR are \
49 | ... | discovered for different Ethernet L2 frame sizes using MLRsearch \
52 | ... | - **[Ref] Applicable standard specifications:** RFC6830.
55 | @{plugins_to_enable}= | dpdk_plugin.so | perfmon_plugin.so | lisp_plugin.so
56 | ${crypto_type}= | ${None}
57 | ${nic_name}= | Intel-X710
58 | ${nic_driver}= | vfio-pci
59 | ${nic_rxq_size}= | 0
60 | ${nic_txq_size}= | 0
64 | ${overhead}= | ${48}
66 | ${traffic_profile}= | trex-stl-3n-ethip6-ip6src253
71 | | ... | - **[Cfg]** DUT runs IPv6 LISP remote static mappings and whitelist \
72 | | ... | filters config. \
73 | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
74 | | ... | - **[Ver]** Measure NDR and PDR values using MLRsearch algorithm.
76 | | ... | *Arguments:*
77 | | ... | - frame_size - Frame size in Bytes as integer or string (IMIX_v4_1).
78 | | ... | Type: integer, string
79 | | ... | - phy_cores - Number of physical cores. Type: integer
80 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
82 | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
84 | | Set Test Variable | \${frame_size}
86 | | Given Set Max Rate And Jumbo
87 | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
88 | | And Pre-initialize layer driver | ${nic_driver}
89 | | And Apply startup configuration on all VPP DUTs
90 | | When Initialize layer driver | ${nic_driver}
91 | | And Initialize layer interface
92 | | And Initialize LISP IPv6 over IPv4 forwarding in 3-node circular topology
93 | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
94 | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
95 | | And Configure LISP topology in 3-node circular topology
96 | | ... | ${dut1} | ${DUT1_${int}2}[0] | ${NONE}
97 | | ... | ${dut2} | ${DUT2_${int}1}[0] | ${NONE}
98 | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
99 | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
100 | | Then Find NDR and PDR intervals using optimized search
103 | 78B-1c-ethip6lispip4-ip6base-ndrpdr
104 | | [Tags] | 78B | 1C
105 | | frame_size=${78} | phy_cores=${1}
107 | 78B-2c-ethip6lispip4-ip6base-ndrpdr
108 | | [Tags] | 78B | 2C
109 | | frame_size=${78} | phy_cores=${2}
111 | 78B-4c-ethip6lispip4-ip6base-ndrpdr
112 | | [Tags] | 78B | 4C
113 | | frame_size=${78} | phy_cores=${4}
115 | 1518B-1c-ethip6lispip4-ip6base-ndrpdr
116 | | [Tags] | 1518B | 1C
117 | | frame_size=${1518} | phy_cores=${1}
119 | 1518B-2c-ethip6lispip4-ip6base-ndrpdr
120 | | [Tags] | 1518B | 2C
121 | | frame_size=${1518} | phy_cores=${2}
123 | 1518B-4c-ethip6lispip4-ip6base-ndrpdr
124 | | [Tags] | 1518B | 4C
125 | | frame_size=${1518} | phy_cores=${4}
127 | 9000B-1c-ethip6lispip4-ip6base-ndrpdr
128 | | [Tags] | 9000B | 1C
129 | | frame_size=${9000} | phy_cores=${1}
131 | 9000B-2c-ethip6lispip4-ip6base-ndrpdr
132 | | [Tags] | 9000B | 2C
133 | | frame_size=${9000} | phy_cores=${2}
135 | 9000B-4c-ethip6lispip4-ip6base-ndrpdr
136 | | [Tags] | 9000B | 4C
137 | | frame_size=${9000} | phy_cores=${4}
139 | IMIX-1c-ethip6lispip4-ip6base-ndrpdr
140 | | [Tags] | IMIX | 1C
141 | | frame_size=IMIX_v4_1 | phy_cores=${1}
143 | IMIX-2c-ethip6lispip4-ip6base-ndrpdr
144 | | [Tags] | IMIX | 2C
145 | | frame_size=IMIX_v4_1 | phy_cores=${2}
147 | IMIX-4c-ethip6lispip4-ip6base-ndrpdr
148 | | [Tags] | IMIX | 4C
149 | | frame_size=IMIX_v4_1 | phy_cores=${4}