/*- * BSD LICENSE * * Copyright(c) 2014-2015 Chelsio Communications. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * * Neither the name of Chelsio Communications nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "common.h" #include "t4_regs.h" #include "t4_regs_values.h" #include "t4fw_interface.h" static void init_link_config(struct link_config *lc, unsigned int caps); /** * t4_read_mtu_tbl - returns the values in the HW path MTU table * @adap: the adapter * @mtus: where to store the MTU values * @mtu_log: where to store the MTU base-2 log (may be %NULL) * * Reads the HW path MTU table. */ void t4_read_mtu_tbl(struct adapter *adap, u16 *mtus, u8 *mtu_log) { u32 v; int i; for (i = 0; i < NMTUS; ++i) { t4_write_reg(adap, A_TP_MTU_TABLE, V_MTUINDEX(0xff) | V_MTUVALUE(i)); v = t4_read_reg(adap, A_TP_MTU_TABLE); mtus[i] = G_MTUVALUE(v); if (mtu_log) mtu_log[i] = G_MTUWIDTH(v); } } /** * t4_tp_wr_bits_indirect - set/clear bits in an indirect TP register * @adap: the adapter * @addr: the indirect TP register address * @mask: specifies the field within the register to modify * @val: new value for the field * * Sets a field of an indirect TP register to the given value. */ void t4_tp_wr_bits_indirect(struct adapter *adap, unsigned int addr, unsigned int mask, unsigned int val) { t4_write_reg(adap, A_TP_PIO_ADDR, addr); val |= t4_read_reg(adap, A_TP_PIO_DATA) & ~mask; t4_write_reg(adap, A_TP_PIO_DATA, val); } /* The minimum additive increment value for the congestion control table */ #define CC_MIN_INCR 2U /** * t4_load_mtus - write the MTU and congestion control HW tables * @adap: the adapter * @mtus: the values for the MTU table * @alpha: the values for the congestion control alpha parameter * @beta: the values for the congestion control beta parameter * * Write the HW MTU table with the supplied MTUs and the high-speed * congestion control table with the supplied alpha, beta, and MTUs. * We write the two tables together because the additive increments * depend on the MTUs. */ void t4_load_mtus(struct adapter *adap, const unsigned short *mtus, const unsigned short *alpha, const unsigned short *beta) { static const unsigned int avg_pkts[NCCTRL_WIN] = { 2, 6, 10, 14, 20, 28, 40, 56, 80, 112, 160, 224, 320, 448, 640, 896, 1281, 1792, 2560, 3584, 5120, 7168, 10240, 14336, 20480, 28672, 40960, 57344, 81920, 114688, 163840, 229376 }; unsigned int i, w; for (i = 0; i < NMTUS; ++i) { unsigned int mtu = mtus[i]; unsigned int log2 = cxgbe_fls(mtu); if (!(mtu & ((1 << log2) >> 2))) /* round */ log2--; t4_write_reg(adap, A_TP_MTU_TABLE, V_MTUINDEX(i) | V_MTUWIDTH(log2) | V_MTUVALUE(mtu)); for (w = 0; w < NCCTRL_WIN; ++w) { unsigned int inc; inc = max(((mtu - 40) * alpha[w]) / avg_pkts[w], CC_MIN_INCR); t4_write_reg(adap, A_TP_CCTRL_TABLE, (i << 21) | (w << 16) | (beta[w] << 13) | inc); } } } /** * t4_wait_op_done_val - wait until an operation is completed * @adapter: the adapter performing the operation * @reg: the register to check for completion * @mask: a single-bit field within @reg that indicates completion * @polarity: the value of the field when the operation is completed * @attempts: number of check iterations * @delay: delay in usecs between iterations * @valp: where to store the value of the register at completion time * * Wait until an operation is completed by checking a bit in a register * up to @attempts times. If @valp is not NULL the value of the register * at the time it indicated completion is stored there. Returns 0 if the * operation completes and -EAGAIN otherwise. */ int t4_wait_op_done_val(struct adapter *adapter, int reg, u32 mask, int polarity, int attempts, int delay, u32 *valp) { while (1) { u32 val = t4_read_reg(adapter, reg); if (!!(val & mask) == polarity) { if (valp) *valp = val; return 0; } if (--attempts == 0) return -EAGAIN; if (delay) udelay(delay); } } /** * t4_set_reg_field - set a register field to a value * @adapter: the adapter to program * @addr: the register address * @mask: specifies the portion of the register to modify * @val: the new value for the register field * * Sets a register field specified by the supplied mask to the * given value. */ void t4_set_reg_field(struct adapter *adapter, unsigned int addr, u32 mask, u32 val) { u32 v = t4_read_reg(adapter, addr) & ~mask; t4_write_reg(adapter, addr, v | val); (void)t4_read_reg(adapter, addr); /* flush */ } /** * t4_read_indirect - read indirectly addressed registers * @adap: the adapter * @addr_reg: register holding the indirect address * @data_reg: register holding the value of the indirect register * @vals: where the read register values are stored * @nregs: how many indirect registers to read * @start_idx: index of first indirect register to read * * Reads registers that are accessed indirectly through an address/data * register pair. */ void t4_read_indirect(struct adapter *adap, unsigned int addr_reg, unsigned int data_reg, u32 *vals, unsigned int nregs, unsigned int start_idx) { while (nregs--) { t4_write_reg(adap, addr_reg, start_idx); *vals++ = t4_read_reg(adap, data_reg); start_idx++; } } /** * t4_write_indirect - write indirectly addressed registers * @adap: the adapter * @addr_reg: register holding the indirect addresses * @data_reg: register holding the value for the indirect registers * @vals: values to write * @nregs: how many indirect registers to write * @start_idx: address of first indirect register to write * * Writes a sequential block of registers that are accessed indirectly * through an address/data register pair. */ void t4_write_indirect(struct adapter *adap, unsigned int addr_reg, unsigned int data_reg, const u32 *vals, unsigned int nregs, unsigned int start_idx) { while (nregs--) { t4_write_reg(adap, addr_reg, start_idx++); t4_write_reg(adap, data_reg, *vals++); } } /** * t4_report_fw_error - report firmware error * @adap: the adapter * * The adapter firmware can indicate error conditions to the host. * If the firmware has indicated an error, print out the reason for * the firmware error. */ static void t4_report_fw_error(struct adapter *adap) { static const char * const reason[] = { "Crash", /* PCIE_FW_EVAL_CRASH */ "During Device Preparation", /* PCIE_FW_EVAL_PREP */ "During Device Configuration", /* PCIE_FW_EVAL_CONF */ "During Device Initialization", /* PCIE_FW_EVAL_INIT */ "Unexpected Event", /* PCIE_FW_EVAL_UNEXPECTEDEVENT */ "Insufficient Airflow", /* PCIE_FW_EVAL_OVERHEAT */ "Device Shutdown", /* PCIE_FW_EVAL_DEVICESHUTDOWN */ "Reserved", /* reserved */ }; u32 pcie_fw; pcie_fw = t4_read_reg(adap, A_PCIE_FW); if (pcie_fw & F_PCIE_FW_ERR) pr_err("%s: Firmware reports adapter error: %s\n", __func__, reason[G_PCIE_FW_EVAL(pcie_fw)]); } /* * Get the reply to a mailbox command and store it in @rpl in big-endian order. */ static void get_mbox_rpl(struct adapter *adap, __be64 *rpl, int nflit, u32 mbox_addr) { for ( ; nflit; nflit--, mbox_addr += 8) *rpl++ = htobe64(t4_read_reg64(adap, mbox_addr)); } /* * Handle a FW assertion reported in a mailbox. */ static void fw_asrt(struct adapter *adap, u32 mbox_addr) { struct fw_debug_cmd asrt; get_mbox_rpl(adap, (__be64 *)&asrt, sizeof(asrt) / 8, mbox_addr); pr_warn("FW assertion at %.16s:%u, val0 %#x, val1 %#x\n", asrt.u.assert.filename_0_7, be32_to_cpu(asrt.u.assert.line), be32_to_cpu(asrt.u.assert.x), be32_to_cpu(asrt.u.assert.y)); } #define X_CIM_PF_NOACCESS 0xeeeeeeee /* * If the Host OS Driver needs locking arround accesses to the mailbox, this * can be turned on via the T4_OS_NEEDS_MBOX_LOCKING CPP define ... */ /* makes single-statement usage a bit cleaner ... */ #ifdef T4_OS_NEEDS_MBOX_LOCKING #define T4_OS_MBOX_LOCKING(x) x #else #define T4_OS_MBOX_LOCKING(x) do {} while (0) #endif /** * t4_wr_mbox_meat_timeout - send a command to FW through the given mailbox * @adap: the adapter * @mbox: index of the mailbox to use * @cmd: the command to write * @size: command length in bytes * @rpl: where to optionally store the reply * @sleep_ok: if true we may sleep while awaiting command completion * @timeout: time to wait for command to finish before timing out * (negative implies @sleep_ok=false) * * Sends the given command to FW through the selected mailbox and waits * for the FW to execute the command. If @rpl is not %NULL it is used to * store the FW's reply to the command. The command and its optional * reply are of the same length. Some FW commands like RESET and * INITIALIZE can take a considerable amount of time to execute. * @sleep_ok determines whether we may sleep while awaiting the response. * If sleeping is allowed we use progressive backoff otherwise we spin. * Note that passing in a negative @timeout is an alternate mechanism * for specifying @sleep_ok=false. This is useful when a higher level * interface allows for specification of @timeout but not @sleep_ok ... * * Returns 0 on success or a negative errno on failure. A * failure can happen either because we are not able to execute the * command or FW executes it but signals an error. In the latter case * the return value is the error code indicated by FW (negated). */ int t4_wr_mbox_meat_timeout(struct adapter *adap, int mbox, const void __attribute__((__may_alias__)) *cmd, int size, void *rpl, bool sleep_ok, int timeout) { /* * We delay in small increments at first in an effort to maintain * responsiveness for simple, fast executing commands but then back * off to larger delays to a maximum retry delay. */ static const int delay[] = { 1, 1, 3, 5, 10, 10, 20, 50, 100 }; u32 v; u64 res; int i, ms; unsigned int delay_idx; __be64 *temp = (__be64 *)malloc(size * sizeof(char)); __be64 *p = temp; u32 data_reg = PF_REG(mbox, A_CIM_PF_MAILBOX_DATA); u32 ctl_reg = PF_REG(mbox, A_CIM_PF_MAILBOX_CTRL); u32 ctl; struct mbox_entry entry; u32 pcie_fw = 0; if ((size & 15) || size > MBOX_LEN) { free(temp); return -EINVAL; } bzero(p, size); memcpy(p, (const __be64 *)cmd, size); /* * If we have a negative timeout, that implies that we can't sleep. */ if (timeout < 0) { sleep_ok = false; timeout = -timeout; } #ifdef T4_OS_NEEDS_MBOX_LOCKING /* * Queue ourselves onto the mailbox access list. When our entry is at * the front of the list, we have rights to access the mailbox. So we * wait [for a while] till we're at the front [or bail out with an * EBUSY] ... */ t4_os_atomic_add_tail(&entry, &adap->mbox_list, &adap->mbox_lock); delay_idx = 0; ms = delay[0]; for (i = 0; ; i += ms) { /* * If we've waited too long, return a busy indication. This * really ought to be based on our initial position in the * mailbox access list but this is a start. We very rarely * contend on access to the mailbox ... Also check for a * firmware error which we'll report as a device error. */ pcie_fw = t4_read_reg(adap, A_PCIE_FW); if (i > 4 * timeout || (pcie_fw & F_PCIE_FW_ERR)) { t4_os_atomic_list_del(&entry, &adap->mbox_list, &adap->mbox_lock); t4_report_fw_error(adap); return (pcie_fw & F_PCIE_FW_ERR) ? -ENXIO : -EBUSY; } /* * If we're at the head, break out and start the mailbox * protocol. */ if (t4_os_list_first_entry(&adap->mbox_list) == &entry) break; /* * Delay for a bit before checking again ... */ if (sleep_ok) { ms = delay[delay_idx]; /* last element may repeat */ if (delay_idx < ARRAY_SIZE(delay) - 1) delay_idx++; msleep(ms); } else { rte_delay_ms(ms); } } #endif /* T4_OS_NEEDS_MBOX_LOCKING */ /* * Attempt to gain access to the mailbox. */ for (i = 0; i < 4; i++) { ctl = t4_read_reg(adap, ctl_reg); v = G_MBOWNER(ctl); if (v != X_MBOWNER_NONE) break; } /* * If we were unable to gain access, dequeue ourselves from the * mailbox atomic access list and report the error to our caller. */ if (v != X_MBOWNER_PL) { T4_OS_MBOX_LOCKING(t4_os_atomic_list_del(&entry, &adap->mbox_list, &adap->mbox_lock)); t4_report_fw_error(adap); return (v == X_MBOWNER_FW ? -EBUSY : -ETIMEDOUT); } /* * If we gain ownership of the mailbox and there's a "valid" message * in it, this is likely an asynchronous error message from the * firmware. So we'll report that and then proceed on with attempting * to issue our own command ... which may well fail if the error * presaged the firmware crashing ... */ if (ctl & F_MBMSGVALID) { dev_err(adap, "found VALID command in mbox %u: " "%llx %llx %llx %llx %llx %llx %llx %llx\n", mbox, (unsigned long long)t4_read_reg64(adap, data_reg), (unsigned long long)t4_read_reg64(adap, data_reg + 8), (unsigned long long)t4_read_reg64(adap, data_reg + 16), (unsigned long long)t4_read_reg64(adap, data_reg + 24), (unsigned long long)t4_read_reg64(adap, data_reg + 32), (unsigned long long)t4_read_reg64(adap, data_reg + 40), (unsigned long long)t4_read_reg64(adap, data_reg + 48), (unsigned long long)t4_read_reg64(adap, data_reg + 56)); } /* * Copy in the new mailbox command and send it on its way ... */ for (i = 0; i < size; i += 8, p++) t4_write_reg64(adap, data_reg + i, be64_to_cpu(*p)); CXGBE_DEBUG_MBOX(adap, "%s: mbox %u: %016llx %016llx %016llx %016llx " "%016llx %016llx %016llx %016llx\n", __func__, (mbox), (unsigned long long)t4_read_reg64(adap, data_reg), (unsigned long long)t4_read_reg64(adap, data_reg + 8), (unsigned long long)t4_read_reg64(adap, data_reg + 16), (unsigned long long)t4_read_reg64(adap, data_reg + 24), (unsigned long long)t4_read_reg64(adap, data_reg + 32), (unsigned long long)t4_read_reg64(adap, data_reg + 40), (unsigned long long)t4_read_reg64(adap, data_reg + 48), (unsigned long long)t4_read_reg64(adap, data_reg + 56)); t4_write_reg(adap, ctl_reg, F_MBMSGVALID | V_MBOWNER(X_MBOWNER_FW)); t4_read_reg(adap, ctl_reg); /* flush write */ delay_idx = 0; ms = delay[0]; /* * Loop waiting for the reply; bail out if we time out or the firmware * reports an error. */ pcie_fw = t4_read_reg(adap, A_PCIE_FW); for (i = 0; i < timeout && !(pcie_fw & F_PCIE_FW_ERR); i += ms) { if (sleep_ok) { ms = delay[delay_idx]; /* last element may repeat */ if (delay_idx < ARRAY_SIZE(delay) - 1) delay_idx++; msleep(ms); } else { msleep(ms); } pcie_fw = t4_read_reg(adap, A_PCIE_FW); v = t4_read_reg(adap, ctl_reg); if (v == X_CIM_PF_NOACCESS) continue; if (G_MBOWNER(v) == X_MBOWNER_PL) { if (!(v & F_MBMSGVALID)) { t4_write_reg(adap, ctl_reg, V_MBOWNER(X_MBOWNER_NONE)); continue; } CXGBE_DEBUG_MBOX(adap, "%s: mbox %u: %016llx %016llx %016llx %016llx " "%016llx %016llx %016llx %016llx\n", __func__, (mbox), (unsigned long long)t4_read_reg64(adap, data_reg), (unsigned long long)t4_read_reg64(adap, data_reg + 8), (unsigned long long)t4_read_reg64(adap, data_reg + 16), (unsigned long long)t4_read_reg64(adap, data_reg + 24), (unsigned long long)t4_read_reg64(adap, data_reg + 32), (unsigned long long)t4_read_reg64(adap, data_reg + 40), (unsigned long long)t4_read_reg64(adap, data_reg + 48), (unsigned long long)t4_read_reg64(adap, data_reg + 56)); CXGBE_DEBUG_MBOX(adap, "command %#x completed in %d ms (%ssleeping)\n", *(const u8 *)cmd, i + ms, sleep_ok ? "" : "non-"); res = t4_read_reg64(adap, data_reg); if (G_FW_CMD_OP(res >> 32) == FW_DEBUG_CMD) { fw_asrt(adap, data_reg); res = V_FW_CMD_RETVAL(EIO); } else if (rpl) { get_mbox_rpl(adap, rpl, size / 8, data_reg); } t4_write_reg(adap, ctl_reg, V_MBOWNER(X_MBOWNER_NONE)); T4_OS_MBOX_LOCKING( t4_os_atomic_list_del(&entry, &adap->mbox_list, &adap->mbox_lock)); return -G_FW_CMD_RETVAL((int)res); } } /* * We timed out waiting for a reply to our mailbox command. Report * the error and also check to see if the firmware reported any * errors ... */ dev_err(adap, "command %#x in mailbox %d timed out\n", *(const u8 *)cmd, mbox); T4_OS_MBOX_LOCKING(t4_os_atomic_list_del(&entry, &adap->mbox_list, &adap->mbox_lock)); t4_report_fw_error(adap); free(temp); return (pcie_fw & F_PCIE_FW_ERR) ? -ENXIO : -ETIMEDOUT; } int t4_wr_mbox_meat(struct adapter *adap, int mbox, const void *cmd, int size, void *rpl, bool sleep_ok) { return t4_wr_mbox_meat_timeout(adap, mbox, cmd, size, rpl, sleep_ok, FW_CMD_MAX_TIMEOUT); } /** * t4_config_rss_range - configure a portion of the RSS mapping table * @adapter: the adapter * @mbox: mbox to use for the FW command * @viid: virtual interface whose RSS subtable is to be written * @start: start entry in the table to write * @n: how many table entries to write * @rspq: values for the "response queue" (Ingress Queue) lookup table * @nrspq: number of values in @rspq * * Programs the selected part of the VI's RSS mapping table with the * provided values. If @nrspq < @n the supplied values are used repeatedly * until the full table range is populated. * * The caller must ensure the values in @rspq are in the range allowed for * @viid. */ int t4_config_rss_range(struct adapter *adapter, int mbox, unsigned int viid, int start, int n, const u16 *rspq, unsigned int nrspq) { int ret; const u16 *rsp = rspq; const u16 *rsp_end = rspq + nrspq; struct fw_rss_ind_tbl_cmd cmd; memset(&cmd, 0, sizeof(cmd)); cmd.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_RSS_IND_TBL_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_WRITE | V_FW_RSS_IND_TBL_CMD_VIID(viid)); cmd.retval_len16 = cpu_to_be32(FW_LEN16(cmd)); /* * Each firmware RSS command can accommodate up to 32 RSS Ingress * Queue Identifiers. These Ingress Queue IDs are packed three to * a 32-bit word as 10-bit values with the upper remaining 2 bits * reserved. */ while (n > 0) { int nq = min(n, 32); int nq_packed = 0; __be32 *qp = &cmd.iq0_to_iq2; /* * Set up the firmware RSS command header to send the next * "nq" Ingress Queue IDs to the firmware. */ cmd.niqid = cpu_to_be16(nq); cmd.startidx = cpu_to_be16(start); /* * "nq" more done for the start of the next loop. */ start += nq; n -= nq; /* * While there are still Ingress Queue IDs to stuff into the * current firmware RSS command, retrieve them from the * Ingress Queue ID array and insert them into the command. */ while (nq > 0) { /* * Grab up to the next 3 Ingress Queue IDs (wrapping * around the Ingress Queue ID array if necessary) and * insert them into the firmware RSS command at the * current 3-tuple position within the commad. */ u16 qbuf[3]; u16 *qbp = qbuf; int nqbuf = min(3, nq); nq -= nqbuf; qbuf[0] = 0; qbuf[1] = 0; qbuf[2] = 0; while (nqbuf && nq_packed < 32) { nqbuf--; nq_packed++; *qbp++ = *rsp++; if (rsp >= rsp_end) rsp = rspq; } *qp++ = cpu_to_be32(V_FW_RSS_IND_TBL_CMD_IQ0(qbuf[0]) | V_FW_RSS_IND_TBL_CMD_IQ1(qbuf[1]) | V_FW_RSS_IND_TBL_CMD_IQ2(qbuf[2])); } /* * Send this portion of the RRS table update to the firmware; * bail out on any errors. */ ret = t4_wr_mbox(adapter, mbox, &cmd, sizeof(cmd), NULL); if (ret) return ret; } return 0; } /** * t4_config_vi_rss - configure per VI RSS settings * @adapter: the adapter * @mbox: mbox to use for the FW command * @viid: the VI id * @flags: RSS flags * @defq: id of the default RSS queue for the VI. * * Configures VI-specific RSS properties. */ int t4_config_vi_rss(struct adapter *adapter, int mbox, unsigned int viid, unsigned int flags, unsigned int defq) { struct fw_rss_vi_config_cmd c; memset(&c, 0, sizeof(c)); c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_RSS_VI_CONFIG_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_WRITE | V_FW_RSS_VI_CONFIG_CMD_VIID(viid)); c.retval_len16 = cpu_to_be32(FW_LEN16(c)); c.u.basicvirtual.defaultq_to_udpen = cpu_to_be32(flags | V_FW_RSS_VI_CONFIG_CMD_DEFAULTQ(defq)); return t4_wr_mbox(adapter, mbox, &c, sizeof(c), NULL); } /** * init_cong_ctrl - initialize congestion control parameters * @a: the alpha values for congestion control * @b: the beta values for congestion control * * Initialize the congestion control parameters. */ static void init_cong_ctrl(unsigned short *a, unsigned short *b) { int i; for (i = 0; i < 9; i++) { a[i] = 1; b[i] = 0; } a[9] = 2; a[10] = 3; a[11] = 4; a[12] = 5; a[13] = 6; a[14] = 7; a[15] = 8; a[16] = 9; a[17] = 10; a[18] = 14; a[19] = 17; a[20] = 21; a[21] = 25; a[22] = 30; a[23] = 35; a[24] = 45; a[25] = 60; a[26] = 80; a[27] = 100; a[28] = 200; a[29] = 300; a[30] = 400; a[31] = 500; b[9] = 1; b[10] = 1; b[11] = 2; b[12] = 2; b[13] = 3; b[14] = 3; b[15] = 3; b[16] = 3; b[17] = 4; b[18] = 4; b[19] = 4; b[20] = 4; b[21] = 4; b[22] = 5; b[23] = 5; b[24] = 5; b[25] = 5; b[26] = 5; b[27] = 5; b[28] = 6; b[29] = 6; b[30] = 7; b[31] = 7; } #define INIT_CMD(var, cmd, rd_wr) do { \ (var).op_to_write = cpu_to_be32(V_FW_CMD_OP(FW_##cmd##_CMD) | \ F_FW_CMD_REQUEST | F_FW_CMD_##rd_wr); \ (var).retval_len16 = cpu_to_be32(FW_LEN16(var)); \ } while (0) int t4_get_core_clock(struct adapter *adapter, struct vpd_params *p) { u32 cclk_param, cclk_val; int ret; /* * Ask firmware for the Core Clock since it knows how to translate the * Reference Clock ('V2') VPD field into a Core Clock value ... */ cclk_param = (V_FW_PARAMS_MNEM(FW_PARAMS_MNEM_DEV) | V_FW_PARAMS_PARAM_X(FW_PARAMS_PARAM_DEV_CCLK)); ret = t4_query_params(adapter, adapter->mbox, adapter->pf, 0, 1, &cclk_param, &cclk_val); if (ret) { dev_err(adapter, "%s: error in fetching from coreclock - %d\n", __func__, ret); return ret; } p->cclk = cclk_val; dev_debug(adapter, "%s: p->cclk = %u\n", __func__, p->cclk); return 0; } /* serial flash and firmware constants and flash config file constants */ enum { SF_ATTEMPTS = 10, /* max retries for SF operations */ /* flash command opcodes */ SF_PROG_PAGE = 2, /* program page */ SF_WR_DISABLE = 4, /* disable writes */ SF_RD_STATUS = 5, /* read status register */ SF_WR_ENABLE = 6, /* enable writes */ SF_RD_DATA_FAST = 0xb, /* read flash */ SF_RD_ID = 0x9f, /* read ID */ SF_ERASE_SECTOR = 0xd8, /* erase sector */ }; /** * sf1_read - read data from the serial flash * @adapter: the adapter * @byte_cnt: number of bytes to read * @cont: whether another operation will be chained * @lock: whether to lock SF for PL access only * @valp: where to store the read data * * Reads up to 4 bytes of data from the serial flash. The location of * the read needs to be specified prior to calling this by issuing the * appropriate commands to the serial flash. */ static int sf1_read(struct adapter *adapter, unsigned int byte_cnt, int cont, int lock, u32 *valp) { int ret; if (!byte_cnt || byte_cnt > 4) return -EINVAL; if (t4_read_reg(adapter, A_SF_OP) & F_BUSY) return -EBUSY; t4_write_reg(adapter, A_SF_OP, V_SF_LOCK(lock) | V_CONT(cont) | V_BYTECNT(byte_cnt - 1)); ret = t4_wait_op_done(adapter, A_SF_OP, F_BUSY, 0, SF_ATTEMPTS, 5); if (!ret) *valp = t4_read_reg(adapter, A_SF_DATA); return ret; } /** * sf1_write - write data to the serial flash * @adapter: the adapter * @byte_cnt: number of bytes to write * @cont: whether another operation will be chained * @lock: whether to lock SF for PL access only * @val: value to write * * Writes up to 4 bytes of data to the serial flash. The location of * the write needs to be specified prior to calling this by issuing the * appropriate commands to the serial flash. */ static int sf1_write(struct adapter *adapter, unsigned int byte_cnt, int cont, int lock, u32 val) { if (!byte_cnt || byte_cnt > 4) return -EINVAL; if (t4_read_reg(adapter, A_SF_OP) & F_BUSY) return -EBUSY; t4_write_reg(adapter, A_SF_DATA, val); t4_write_reg(adapter, A_SF_OP, V_SF_LOCK(lock) | V_CONT(cont) | V_BYTECNT(byte_cnt - 1) | V_OP(1)); return t4_wait_op_done(adapter, A_SF_OP, F_BUSY, 0, SF_ATTEMPTS, 5); } /** * t4_read_flash - read words from serial flash * @adapter: the adapter * @addr: the start address for the read * @nwords: how many 32-bit words to read * @data: where to store the read data * @byte_oriented: whether to store data as bytes or as words * * Read the specified number of 32-bit words from the serial flash. * If @byte_oriented is set the read data is stored as a byte array * (i.e., big-endian), otherwise as 32-bit words in the platform's * natural endianness. */ int t4_read_flash(struct adapter *adapter, unsigned int addr, unsigned int nwords, u32 *data, int byte_oriented) { int ret; if (((addr + nwords * sizeof(u32)) > adapter->params.sf_size) || (addr & 3)) return -EINVAL; addr = rte_constant_bswap32(addr) | SF_RD_DATA_FAST; ret = sf1_write(adapter, 4, 1, 0, addr); if (ret != 0) return ret; ret = sf1_read(adapter, 1, 1, 0, data); if (ret != 0) return ret; for ( ; nwords; nwords--, data++) { ret = sf1_read(adapter, 4, nwords > 1, nwords == 1, data); if (nwords == 1) t4_write_reg(adapter, A_SF_OP, 0); /* unlock SF */ if (ret) return ret; if (byte_oriented) *data = cpu_to_be32(*data); } return 0; } /** * t4_get_fw_version - read the firmware version * @adapter: the adapter * @vers: where to place the version * * Reads the FW version from flash. */ int t4_get_fw_version(struct adapter *adapter, u32 *vers) { return t4_read_flash(adapter, FLASH_FW_START + offsetof(struct fw_hdr, fw_ver), 1, vers, 0); } /** * t4_get_tp_version - read the TP microcode version * @adapter: the adapter * @vers: where to place the version * * Reads the TP microcode version from flash. */ int t4_get_tp_version(struct adapter *adapter, u32 *vers) { return t4_read_flash(adapter, FLASH_FW_START + offsetof(struct fw_hdr, tp_microcode_ver), 1, vers, 0); } #define ADVERT_MASK (FW_PORT_CAP_SPEED_100M | FW_PORT_CAP_SPEED_1G |\ FW_PORT_CAP_SPEED_10G | FW_PORT_CAP_SPEED_40G | \ FW_PORT_CAP_SPEED_100G | FW_PORT_CAP_ANEG) /** * t4_link_l1cfg - apply link configuration to MAC/PHY * @phy: the PHY to setup * @mac: the MAC to setup * @lc: the requested link configuration * * Set up a port's MAC and PHY according to a desired link configuration. * - If the PHY can auto-negotiate first decide what to advertise, then * enable/disable auto-negotiation as desired, and reset. * - If the PHY does not auto-negotiate just reset it. * - If auto-negotiation is off set the MAC to the proper speed/duplex/FC, * otherwise do it later based on the outcome of auto-negotiation. */ int t4_link_l1cfg(struct adapter *adap, unsigned int mbox, unsigned int port, struct link_config *lc) { struct fw_port_cmd c; unsigned int fc = 0, mdi = V_FW_PORT_CAP_MDI(FW_PORT_CAP_MDI_AUTO); lc->link_ok = 0; if (lc->requested_fc & PAUSE_RX) fc |= FW_PORT_CAP_FC_RX; if (lc->requested_fc & PAUSE_TX) fc |= FW_PORT_CAP_FC_TX; memset(&c, 0, sizeof(c)); c.op_to_portid = cpu_to_be32(V_FW_CMD_OP(FW_PORT_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_EXEC | V_FW_PORT_CMD_PORTID(port)); c.action_to_len16 = cpu_to_be32(V_FW_PORT_CMD_ACTION(FW_PORT_ACTION_L1_CFG) | FW_LEN16(c)); if (!(lc->supported & FW_PORT_CAP_ANEG)) { c.u.l1cfg.rcap = cpu_to_be32((lc->supported & ADVERT_MASK) | fc); lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); } else if (lc->autoneg == AUTONEG_DISABLE) { c.u.l1cfg.rcap = cpu_to_be32(lc->requested_speed | fc | mdi); lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); } else { c.u.l1cfg.rcap = cpu_to_be32(lc->advertising | fc | mdi); } return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /** * t4_flash_cfg_addr - return the address of the flash configuration file * @adapter: the adapter * * Return the address within the flash where the Firmware Configuration * File is stored, or an error if the device FLASH is too small to contain * a Firmware Configuration File. */ int t4_flash_cfg_addr(struct adapter *adapter) { /* * If the device FLASH isn't large enough to hold a Firmware * Configuration File, return an error. */ if (adapter->params.sf_size < FLASH_CFG_START + FLASH_CFG_MAX_SIZE) return -ENOSPC; return FLASH_CFG_START; } #define PF_INTR_MASK (F_PFSW | F_PFCIM) /** * t4_intr_enable - enable interrupts * @adapter: the adapter whose interrupts should be enabled * * Enable PF-specific interrupts for the calling function and the top-level * interrupt concentrator for global interrupts. Interrupts are already * enabled at each module, here we just enable the roots of the interrupt * hierarchies. * * Note: this function should be called only when the driver manages * non PF-specific interrupts from the various HW modules. Only one PCI * function at a time should be doing this. */ void t4_intr_enable(struct adapter *adapter) { u32 val = 0; u32 pf = G_SOURCEPF(t4_read_reg(adapter, A_PL_WHOAMI)); if (CHELSIO_CHIP_VERSION(adapter->params.chip) <= CHELSIO_T5) val = F_ERR_DROPPED_DB | F_ERR_EGR_CTXT_PRIO | F_DBFIFO_HP_INT; t4_write_reg(adapter, A_SGE_INT_ENABLE3, F_ERR_CPL_EXCEED_IQE_SIZE | F_ERR_INVALID_CIDX_INC | F_ERR_CPL_OPCODE_0 | F_ERR_DATA_CPL_ON_HIGH_QID1 | F_INGRESS_SIZE_ERR | F_ERR_DATA_CPL_ON_HIGH_QID0 | F_ERR_BAD_DB_PIDX3 | F_ERR_BAD_DB_PIDX2 | F_ERR_BAD_DB_PIDX1 | F_ERR_BAD_DB_PIDX0 | F_ERR_ING_CTXT_PRIO | F_DBFIFO_LP_INT | F_EGRESS_SIZE_ERR | val); t4_write_reg(adapter, MYPF_REG(A_PL_PF_INT_ENABLE), PF_INTR_MASK); t4_set_reg_field(adapter, A_PL_INT_MAP0, 0, 1 << pf); } /** * t4_intr_disable - disable interrupts * @adapter: the adapter whose interrupts should be disabled * * Disable interrupts. We only disable the top-level interrupt * concentrators. The caller must be a PCI function managing global * interrupts. */ void t4_intr_disable(struct adapter *adapter) { u32 pf = G_SOURCEPF(t4_read_reg(adapter, A_PL_WHOAMI)); t4_write_reg(adapter, MYPF_REG(A_PL_PF_INT_ENABLE), 0); t4_set_reg_field(adapter, A_PL_INT_MAP0, 1 << pf, 0); } /** * t4_get_port_type_description - return Port Type string description * @port_type: firmware Port Type enumeration */ const char *t4_get_port_type_description(enum fw_port_type port_type) { static const char * const port_type_description[] = { "Fiber_XFI", "Fiber_XAUI", "BT_SGMII", "BT_XFI", "BT_XAUI", "KX4", "CX4", "KX", "KR", "SFP", "BP_AP", "BP4_AP", "QSFP_10G", "QSA", "QSFP", "BP40_BA", }; if (port_type < ARRAY_SIZE(port_type_description)) return port_type_description[port_type]; return "UNKNOWN"; } /** * t4_get_mps_bg_map - return the buffer groups associated with a port * @adap: the adapter * @idx: the port index * * Returns a bitmap indicating which MPS buffer groups are associated * with the given port. Bit i is set if buffer group i is used by the * port. */ unsigned int t4_get_mps_bg_map(struct adapter *adap, int idx) { u32 n = G_NUMPORTS(t4_read_reg(adap, A_MPS_CMN_CTL)); if (n == 0) return idx == 0 ? 0xf : 0; if (n == 1) return idx < 2 ? (3 << (2 * idx)) : 0; return 1 << idx; } /** * t4_get_port_stats - collect port statistics * @adap: the adapter * @idx: the port index * @p: the stats structure to fill * * Collect statistics related to the given port from HW. */ void t4_get_port_stats(struct adapter *adap, int idx, struct port_stats *p) { u32 bgmap = t4_get_mps_bg_map(adap, idx); #define GET_STAT(name) \ t4_read_reg64(adap, \ (is_t4(adap->params.chip) ? \ PORT_REG(idx, A_MPS_PORT_STAT_##name##_L) :\ T5_PORT_REG(idx, A_MPS_PORT_STAT_##name##_L))) #define GET_STAT_COM(name) t4_read_reg64(adap, A_MPS_STAT_##name##_L) p->tx_octets = GET_STAT(TX_PORT_BYTES); p->tx_frames = GET_STAT(TX_PORT_FRAMES); p->tx_bcast_frames = GET_STAT(TX_PORT_BCAST); p->tx_mcast_frames = GET_STAT(TX_PORT_MCAST); p->tx_ucast_frames = GET_STAT(TX_PORT_UCAST); p->tx_error_frames = GET_STAT(TX_PORT_ERROR); p->tx_frames_64 = GET_STAT(TX_PORT_64B); p->tx_frames_65_127 = GET_STAT(TX_PORT_65B_127B); p->tx_frames_128_255 = GET_STAT(TX_PORT_128B_255B); p->tx_frames_256_511 = GET_STAT(TX_PORT_256B_511B); p->tx_frames_512_1023 = GET_STAT(TX_PORT_512B_1023B); p->tx_frames_1024_1518 = GET_STAT(TX_PORT_1024B_1518B); p->tx_frames_1519_max = GET_STAT(TX_PORT_1519B_MAX); p->tx_drop = GET_STAT(TX_PORT_DROP); p->tx_pause = GET_STAT(TX_PORT_PAUSE); p->tx_ppp0 = GET_STAT(TX_PORT_PPP0); p->tx_ppp1 = GET_STAT(TX_PORT_PPP1); p->tx_ppp2 = GET_STAT(TX_PORT_PPP2); p->tx_ppp3 = GET_STAT(TX_PORT_PPP3); p->tx_ppp4 = GET_STAT(TX_PORT_PPP4); p->tx_ppp5 = GET_STAT(TX_PORT_PPP5); p->tx_ppp6 = GET_STAT(TX_PORT_PPP6); p->tx_ppp7 = GET_STAT(TX_PORT_PPP7); p->rx_octets = GET_STAT(RX_PORT_BYTES); p->rx_frames = GET_STAT(RX_PORT_FRAMES); p->rx_bcast_frames = GET_STAT(RX_PORT_BCAST); p->rx_mcast_frames = GET_STAT(RX_PORT_MCAST); p->rx_ucast_frames = GET_STAT(RX_PORT_UCAST); p->rx_too_long = GET_STAT(RX_PORT_MTU_ERROR); p->rx_jabber = GET_STAT(RX_PORT_MTU_CRC_ERROR); p->rx_fcs_err = GET_STAT(RX_PORT_CRC_ERROR); p->rx_len_err = GET_STAT(RX_PORT_LEN_ERROR); p->rx_symbol_err = GET_STAT(RX_PORT_SYM_ERROR); p->rx_runt = GET_STAT(RX_PORT_LESS_64B); p->rx_frames_64 = GET_STAT(RX_PORT_64B); p->rx_frames_65_127 = GET_STAT(RX_PORT_65B_127B); p->rx_frames_128_255 = GET_STAT(RX_PORT_128B_255B); p->rx_frames_256_511 = GET_STAT(RX_PORT_256B_511B); p->rx_frames_512_1023 = GET_STAT(RX_PORT_512B_1023B); p->rx_frames_1024_1518 = GET_STAT(RX_PORT_1024B_1518B); p->rx_frames_1519_max = GET_STAT(RX_PORT_1519B_MAX); p->rx_pause = GET_STAT(RX_PORT_PAUSE); p->rx_ppp0 = GET_STAT(RX_PORT_PPP0); p->rx_ppp1 = GET_STAT(RX_PORT_PPP1); p->rx_ppp2 = GET_STAT(RX_PORT_PPP2); p->rx_ppp3 = GET_STAT(RX_PORT_PPP3); p->rx_ppp4 = GET_STAT(RX_PORT_PPP4); p->rx_ppp5 = GET_STAT(RX_PORT_PPP5); p->rx_ppp6 = GET_STAT(RX_PORT_PPP6); p->rx_ppp7 = GET_STAT(RX_PORT_PPP7); p->rx_ovflow0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_MAC_DROP_FRAME) : 0; p->rx_ovflow1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_MAC_DROP_FRAME) : 0; p->rx_ovflow2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_MAC_DROP_FRAME) : 0; p->rx_ovflow3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_MAC_DROP_FRAME) : 0; p->rx_trunc0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_MAC_TRUNC_FRAME) : 0; p->rx_trunc1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_MAC_TRUNC_FRAME) : 0; p->rx_trunc2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_MAC_TRUNC_FRAME) : 0; p->rx_trunc3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_MAC_TRUNC_FRAME) : 0; #undef GET_STAT #undef GET_STAT_COM } /** * t4_get_port_stats_offset - collect port stats relative to a previous snapshot * @adap: The adapter * @idx: The port * @stats: Current stats to fill * @offset: Previous stats snapshot */ void t4_get_port_stats_offset(struct adapter *adap, int idx, struct port_stats *stats, struct port_stats *offset) { u64 *s, *o; unsigned int i; t4_get_port_stats(adap, idx, stats); for (i = 0, s = (u64 *)stats, o = (u64 *)offset; i < (sizeof(struct port_stats) / sizeof(u64)); i++, s++, o++) *s -= *o; } /** * t4_clr_port_stats - clear port statistics * @adap: the adapter * @idx: the port index * * Clear HW statistics for the given port. */ void t4_clr_port_stats(struct adapter *adap, int idx) { unsigned int i; u32 bgmap = t4_get_mps_bg_map(adap, idx); u32 port_base_addr; if (is_t4(adap->params.chip)) port_base_addr = PORT_BASE(idx); else port_base_addr = T5_PORT_BASE(idx); for (i = A_MPS_PORT_STAT_TX_PORT_BYTES_L; i <= A_MPS_PORT_STAT_TX_PORT_PPP7_H; i += 8) t4_write_reg(adap, port_base_addr + i, 0); for (i = A_MPS_PORT_STAT_RX_PORT_BYTES_L; i <= A_MPS_PORT_STAT_RX_PORT_LESS_64B_H; i += 8) t4_write_reg(adap, port_base_addr + i, 0); for (i = 0; i < 4; i++) if (bgmap & (1 << i)) { t4_write_reg(adap, A_MPS_STAT_RX_BG_0_MAC_DROP_FRAME_L + i * 8, 0); t4_write_reg(adap, A_MPS_STAT_RX_BG_0_MAC_TRUNC_FRAME_L + i * 8, 0); } } /** * t4_fw_hello - establish communication with FW * @adap: the adapter * @mbox: mailbox to use for the FW command * @evt_mbox: mailbox to receive async FW events * @master: specifies the caller's willingness to be the device master * @state: returns the current device state (if non-NULL) * * Issues a command to establish communication with FW. Returns either * an error (negative integer) or the mailbox of the Master PF. */ int t4_fw_hello(struct adapter *adap, unsigned int mbox, unsigned int evt_mbox, enum dev_master master, enum dev_state *state) { int ret; struct fw_hello_cmd c; u32 v; unsigned int master_mbox; int retries = FW_CMD_HELLO_RETRIES; retry: memset(&c, 0, sizeof(c)); INIT_CMD(c, HELLO, WRITE); c.err_to_clearinit = cpu_to_be32( V_FW_HELLO_CMD_MASTERDIS(master == MASTER_CANT) | V_FW_HELLO_CMD_MASTERFORCE(master == MASTER_MUST) | V_FW_HELLO_CMD_MBMASTER(master == MASTER_MUST ? mbox : M_FW_HELLO_CMD_MBMASTER) | V_FW_HELLO_CMD_MBASYNCNOT(evt_mbox) | V_FW_HELLO_CMD_STAGE(FW_HELLO_CMD_STAGE_OS) | F_FW_HELLO_CMD_CLEARINIT); /* * Issue the HELLO command to the firmware. If it's not successful * but indicates that we got a "busy" or "timeout" condition, retry * the HELLO until we exhaust our retry limit. If we do exceed our * retry limit, check to see if the firmware left us any error * information and report that if so ... */ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); if (ret != FW_SUCCESS) { if ((ret == -EBUSY || ret == -ETIMEDOUT) && retries-- > 0) goto retry; if (t4_read_reg(adap, A_PCIE_FW) & F_PCIE_FW_ERR) t4_report_fw_error(adap); return ret; } v = be32_to_cpu(c.err_to_clearinit); master_mbox = G_FW_HELLO_CMD_MBMASTER(v); if (state) { if (v & F_FW_HELLO_CMD_ERR) *state = DEV_STATE_ERR; else if (v & F_FW_HELLO_CMD_INIT) *state = DEV_STATE_INIT; else *state = DEV_STATE_UNINIT; } /* * If we're not the Master PF then we need to wait around for the * Master PF Driver to finish setting up the adapter. * * Note that we also do this wait if we're a non-Master-capable PF and * there is no current Master PF; a Master PF may show up momentarily * and we wouldn't want to fail pointlessly. (This can happen when an * OS loads lots of different drivers rapidly at the same time). In * this case, the Master PF returned by the firmware will be * M_PCIE_FW_MASTER so the test below will work ... */ if ((v & (F_FW_HELLO_CMD_ERR | F_FW_HELLO_CMD_INIT)) == 0 && master_mbox != mbox) { int waiting = FW_CMD_HELLO_TIMEOUT; /* * Wait for the firmware to either indicate an error or * initialized state. If we see either of these we bail out * and report the issue to the caller. If we exhaust the * "hello timeout" and we haven't exhausted our retries, try * again. Otherwise bail with a timeout error. */ for (;;) { u32 pcie_fw; msleep(50); waiting -= 50; /* * If neither Error nor Initialialized are indicated * by the firmware keep waiting till we exaust our * timeout ... and then retry if we haven't exhausted * our retries ... */ pcie_fw = t4_read_reg(adap, A_PCIE_FW); if (!(pcie_fw & (F_PCIE_FW_ERR | F_PCIE_FW_INIT))) { if (waiting <= 0) { if (retries-- > 0) goto retry; return -ETIMEDOUT; } continue; } /* * We either have an Error or Initialized condition * report errors preferentially. */ if (state) { if (pcie_fw & F_PCIE_FW_ERR) *state = DEV_STATE_ERR; else if (pcie_fw & F_PCIE_FW_INIT) *state = DEV_STATE_INIT; } /* * If we arrived before a Master PF was selected and * there's not a valid Master PF, grab its identity * for our caller. */ if (master_mbox == M_PCIE_FW_MASTER && (pcie_fw & F_PCIE_FW_MASTER_VLD)) master_mbox = G_PCIE_FW_MASTER(pcie_fw); break; } } return master_mbox; } /** * t4_fw_bye - end communication with FW * @adap: the adapter * @mbox: mailbox to use for the FW command * * Issues a command to terminate communication with FW. */ int t4_fw_bye(struct adapter *adap, unsigned int mbox) { struct fw_bye_cmd c; memset(&c, 0, sizeof(c)); INIT_CMD(c, BYE, WRITE); return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /** * t4_fw_reset - issue a reset to FW * @adap: the adapter * @mbox: mailbox to use for the FW command * @reset: specifies the type of reset to perform * * Issues a reset command of the specified type to FW. */ int t4_fw_reset(struct adapter *adap, unsigned int mbox, int reset) { struct fw_reset_cmd c; memset(&c, 0, sizeof(c)); INIT_CMD(c, RESET, WRITE); c.val = cpu_to_be32(reset); return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /** * t4_fw_halt - issue a reset/halt to FW and put uP into RESET * @adap: the adapter * @mbox: mailbox to use for the FW RESET command (if desired) * @force: force uP into RESET even if FW RESET command fails * * Issues a RESET command to firmware (if desired) with a HALT indication * and then puts the microprocessor into RESET state. The RESET command * will only be issued if a legitimate mailbox is provided (mbox <= * M_PCIE_FW_MASTER). * * This is generally used in order for the host to safely manipulate the * adapter without fear of conflicting with whatever the firmware might * be doing. The only way out of this state is to RESTART the firmware * ... */ int t4_fw_halt(struct adapter *adap, unsigned int mbox, int force) { int ret = 0; /* * If a legitimate mailbox is provided, issue a RESET command * with a HALT indication. */ if (mbox <= M_PCIE_FW_MASTER) { struct fw_reset_cmd c; memset(&c, 0, sizeof(c)); INIT_CMD(c, RESET, WRITE); c.val = cpu_to_be32(F_PIORST | F_PIORSTMODE); c.halt_pkd = cpu_to_be32(F_FW_RESET_CMD_HALT); ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /* * Normally we won't complete the operation if the firmware RESET * command fails but if our caller insists we'll go ahead and put the * uP into RESET. This can be useful if the firmware is hung or even * missing ... We'll have to take the risk of putting the uP into * RESET without the cooperation of firmware in that case. * * We also force the firmware's HALT flag to be on in case we bypassed * the firmware RESET command above or we're dealing with old firmware * which doesn't have the HALT capability. This will serve as a flag * for the incoming firmware to know that it's coming out of a HALT * rather than a RESET ... if it's new enough to understand that ... */ if (ret == 0 || force) { t4_set_reg_field(adap, A_CIM_BOOT_CFG, F_UPCRST, F_UPCRST); t4_set_reg_field(adap, A_PCIE_FW, F_PCIE_FW_HALT, F_PCIE_FW_HALT); } /* * And we always return the result of the firmware RESET command * even when we force the uP into RESET ... */ return ret; } /** * t4_fw_restart - restart the firmware by taking the uP out of RESET * @adap: the adapter * @mbox: mailbox to use for the FW RESET command (if desired) * @reset: if we want to do a RESET to restart things * * Restart firmware previously halted by t4_fw_halt(). On successful * return the previous PF Master remains as the new PF Master and there * is no need to issue a new HELLO command, etc. * * We do this in two ways: * * 1. If we're dealing with newer firmware we'll simply want to take * the chip's microprocessor out of RESET. This will cause the * firmware to start up from its start vector. And then we'll loop * until the firmware indicates it's started again (PCIE_FW.HALT * reset to 0) or we timeout. * * 2. If we're dealing with older firmware then we'll need to RESET * the chip since older firmware won't recognize the PCIE_FW.HALT * flag and automatically RESET itself on startup. */ int t4_fw_restart(struct adapter *adap, unsigned int mbox, int reset) { if (reset) { /* * Since we're directing the RESET instead of the firmware * doing it automatically, we need to clear the PCIE_FW.HALT * bit. */ t4_set_reg_field(adap, A_PCIE_FW, F_PCIE_FW_HALT, 0); /* * If we've been given a valid mailbox, first try to get the * firmware to do the RESET. If that works, great and we can * return success. Otherwise, if we haven't been given a * valid mailbox or the RESET command failed, fall back to * hitting the chip with a hammer. */ if (mbox <= M_PCIE_FW_MASTER) { t4_set_reg_field(adap, A_CIM_BOOT_CFG, F_UPCRST, 0); msleep(100); if (t4_fw_reset(adap, mbox, F_PIORST | F_PIORSTMODE) == 0) return 0; } t4_write_reg(adap, A_PL_RST, F_PIORST | F_PIORSTMODE); msleep(2000); } else { int ms; t4_set_reg_field(adap, A_CIM_BOOT_CFG, F_UPCRST, 0); for (ms = 0; ms < FW_CMD_MAX_TIMEOUT; ) { if (!(t4_read_reg(adap, A_PCIE_FW) & F_PCIE_FW_HALT)) return FW_SUCCESS; msleep(100); ms += 100; } return -ETIMEDOUT; } return 0; } /** * t4_fixup_host_params_compat - fix up host-dependent parameters * @adap: the adapter * @page_size: the host's Base Page Size * @cache_line_size: the host's Cache Line Size * @chip_compat: maintain compatibility with designated chip * * Various registers in the chip contain values which are dependent on the * host's Base Page and Cache Line Sizes. This function will fix all of * those registers with the appropriate values as passed in ... * * @chip_compat is used to limit the set of changes that are made * to be compatible with the indicated chip release. This is used by * drivers to maintain compatibility with chip register settings when * the drivers haven't [yet] been updated with new chip support. */ int t4_fixup_host_params_compat(struct adapter *adap, unsigned int page_size, unsigned int cache_line_size, enum chip_type chip_compat) { unsigned int page_shift = cxgbe_fls(page_size) - 1; unsigned int sge_hps = page_shift - 10; unsigned int stat_len = cache_line_size > 64 ? 128 : 64; unsigned int fl_align = cache_line_size < 32 ? 32 : cache_line_size; unsigned int fl_align_log = cxgbe_fls(fl_align) - 1; t4_write_reg(adap, A_SGE_HOST_PAGE_SIZE, V_HOSTPAGESIZEPF0(sge_hps) | V_HOSTPAGESIZEPF1(sge_hps) | V_HOSTPAGESIZEPF2(sge_hps) | V_HOSTPAGESIZEPF3(sge_hps) | V_HOSTPAGESIZEPF4(sge_hps) | V_HOSTPAGESIZEPF5(sge_hps) | V_HOSTPAGESIZEPF6(sge_hps) | V_HOSTPAGESIZEPF7(sge_hps)); if (is_t4(adap->params.chip) || is_t4(chip_compat)) t4_set_reg_field(adap, A_SGE_CONTROL, V_INGPADBOUNDARY(M_INGPADBOUNDARY) | F_EGRSTATUSPAGESIZE, V_INGPADBOUNDARY(fl_align_log - X_INGPADBOUNDARY_SHIFT) | V_EGRSTATUSPAGESIZE(stat_len != 64)); else { /* * T5 introduced the separation of the Free List Padding and * Packing Boundaries. Thus, we can select a smaller Padding * Boundary to avoid uselessly chewing up PCIe Link and Memory * Bandwidth, and use a Packing Boundary which is large enough * to avoid false sharing between CPUs, etc. * * For the PCI Link, the smaller the Padding Boundary the * better. For the Memory Controller, a smaller Padding * Boundary is better until we cross under the Memory Line * Size (the minimum unit of transfer to/from Memory). If we * have a Padding Boundary which is smaller than the Memory * Line Size, that'll involve a Read-Modify-Write cycle on the * Memory Controller which is never good. For T5 the smallest * Padding Boundary which we can select is 32 bytes which is * larger than any known Memory Controller Line Size so we'll * use that. */ /* * N.B. T5 has a different interpretation of the "0" value for * the Packing Boundary. This corresponds to 16 bytes instead * of the expected 32 bytes. We never have a Packing Boundary * less than 32 bytes so we can't use that special value but * on the other hand, if we wanted 32 bytes, the best we can * really do is 64 bytes ... */ if (fl_align <= 32) { fl_align = 64; fl_align_log = 6; } t4_set_reg_field(adap, A_SGE_CONTROL, V_INGPADBOUNDARY(M_INGPADBOUNDARY) | F_EGRSTATUSPAGESIZE, V_INGPADBOUNDARY(X_INGPCIEBOUNDARY_32B) | V_EGRSTATUSPAGESIZE(stat_len != 64)); t4_set_reg_field(adap, A_SGE_CONTROL2, V_INGPACKBOUNDARY(M_INGPACKBOUNDARY), V_INGPACKBOUNDARY(fl_align_log - X_INGPACKBOUNDARY_SHIFT)); } /* * Adjust various SGE Free List Host Buffer Sizes. * * The first four entries are: * * 0: Host Page Size * 1: 64KB * 2: Buffer size corresponding to 1500 byte MTU (unpacked mode) * 3: Buffer size corresponding to 9000 byte MTU (unpacked mode) * * For the single-MTU buffers in unpacked mode we need to include * space for the SGE Control Packet Shift, 14 byte Ethernet header, * possible 4 byte VLAN tag, all rounded up to the next Ingress Packet * Padding boundary. All of these are accommodated in the Factory * Default Firmware Configuration File but we need to adjust it for * this host's cache line size. */ t4_write_reg(adap, A_SGE_FL_BUFFER_SIZE0, page_size); t4_write_reg(adap, A_SGE_FL_BUFFER_SIZE2, (t4_read_reg(adap, A_SGE_FL_BUFFER_SIZE2) + fl_align - 1) & ~(fl_align - 1)); t4_write_reg(adap, A_SGE_FL_BUFFER_SIZE3, (t4_read_reg(adap, A_SGE_FL_BUFFER_SIZE3) + fl_align - 1) & ~(fl_align - 1)); t4_write_reg(adap, A_ULP_RX_TDDP_PSZ, V_HPZ0(page_shift - 12)); return 0; } /** * t4_fixup_host_params - fix up host-dependent parameters (T4 compatible) * @adap: the adapter * @page_size: the host's Base Page Size * @cache_line_size: the host's Cache Line Size * * Various registers in T4 contain values which are dependent on the * host's Base Page and Cache Line Sizes. This function will fix all of * those registers with the appropriate values as passed in ... * * This routine makes changes which are compatible with T4 chips. */ int t4_fixup_host_params(struct adapter *adap, unsigned int page_size, unsigned int cache_line_size) { return t4_fixup_host_params_compat(adap, page_size, cache_line_size, T4_LAST_REV); } /** * t4_fw_initialize - ask FW to initialize the device * @adap: the adapter * @mbox: mailbox to use for the FW command * * Issues a command to FW to partially initialize the device. This * performs initialization that generally doesn't depend on user input. */ int t4_fw_initialize(struct adapter *adap, unsigned int mbox) { struct fw_initialize_cmd c; memset(&c, 0, sizeof(c)); INIT_CMD(c, INITIALIZE, WRITE); return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /** * t4_query_params_rw - query FW or device parameters * @adap: the adapter * @mbox: mailbox to use for the FW command * @pf: the PF * @vf: the VF * @nparams: the number of parameters * @params: the parameter names * @val: the parameter values * @rw: Write and read flag * * Reads the value of FW or device parameters. Up to 7 parameters can be * queried at once. */ static int t4_query_params_rw(struct adapter *adap, unsigned int mbox, unsigned int pf, unsigned int vf, unsigned int nparams, const u32 *params, u32 *val, int rw) { unsigned int i; int ret; struct fw_params_cmd c; __be32 *p = &c.param[0].mnem; if (nparams > 7) return -EINVAL; memset(&c, 0, sizeof(c)); c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_PARAMS_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_READ | V_FW_PARAMS_CMD_PFN(pf) | V_FW_PARAMS_CMD_VFN(vf)); c.retval_len16 = cpu_to_be32(FW_LEN16(c)); for (i = 0; i < nparams; i++) { *p++ = cpu_to_be32(*params++); if (rw) *p = cpu_to_be32(*(val + i)); p++; } ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); if (ret == 0) for (i = 0, p = &c.param[0].val; i < nparams; i++, p += 2) *val++ = be32_to_cpu(*p); return ret; } int t4_query_params(struct adapter *adap, unsigned int mbox, unsigned int pf, unsigned int vf, unsigned int nparams, const u32 *params, u32 *val) { return t4_query_params_rw(adap, mbox, pf, vf, nparams, params, val, 0); } /** * t4_set_params_timeout - sets FW or device parameters * @adap: the adapter * @mbox: mailbox to use for the FW command * @pf: the PF * @vf: the VF * @nparams: the number of parameters * @params: the parameter names * @val: the parameter values * @timeout: the timeout time * * Sets the value of FW or device parameters. Up to 7 parameters can be * specified at once. */ int t4_set_params_timeout(struct adapter *adap, unsigned int mbox, unsigned int pf, unsigned int vf, unsigned int nparams, const u32 *params, const u32 *val, int timeout) { struct fw_params_cmd c; __be32 *p = &c.param[0].mnem; if (nparams > 7) return -EINVAL; memset(&c, 0, sizeof(c)); c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_PARAMS_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_WRITE | V_FW_PARAMS_CMD_PFN(pf) | V_FW_PARAMS_CMD_VFN(vf)); c.retval_len16 = cpu_to_be32(FW_LEN16(c)); while (nparams--) { *p++ = cpu_to_be32(*params++); *p++ = cpu_to_be32(*val++); } return t4_wr_mbox_timeout(adap, mbox, &c, sizeof(c), NULL, timeout); } int t4_set_params(struct adapter *adap, unsigned int mbox, unsigned int pf, unsigned int vf, unsigned int nparams, const u32 *params, const u32 *val) { return t4_set_params_timeout(adap, mbox, pf, vf, nparams, params, val, FW_CMD_MAX_TIMEOUT); } /** * t4_alloc_vi_func - allocate a virtual interface * @adap: the adapter * @mbox: mailbox to use for the FW command * @port: physical port associated with the VI * @pf: the PF owning the VI * @vf: the VF owning the VI * @nmac: number of MAC addresses needed (1 to 5) * @mac: the MAC addresses of the VI * @rss_size: size of RSS table slice associated with this VI * @portfunc: which Port Application Function MAC Address is desired * @idstype: Intrusion Detection Type * * Allocates a virtual interface for the given physical port. If @mac is * not %NULL it contains the MAC addresses of the VI as assigned by FW. * @mac should be large enough to hold @nmac Ethernet addresses, they are * stored consecutively so the space needed is @nmac * 6 bytes. * Returns a negative error number or the non-negative VI id. */ int t4_alloc_vi_func(struct adapter *adap, unsigned int mbox, unsigned int port, unsigned int pf, unsigned int vf, unsigned int nmac, u8 *mac, unsigned int *rss_size, unsigned int portfunc, unsigned int idstype) { int ret; struct fw_vi_cmd c; memset(&c, 0, sizeof(c)); c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_VI_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_WRITE | F_FW_CMD_EXEC | V_FW_VI_CMD_PFN(pf) | V_FW_VI_CMD_VFN(vf)); c.alloc_to_len16 = cpu_to_be32(F_FW_VI_CMD_ALLOC | FW_LEN16(c)); c.type_to_viid = cpu_to_be16(V_FW_VI_CMD_TYPE(idstype) | V_FW_VI_CMD_FUNC(portfunc)); c.portid_pkd = V_FW_VI_CMD_PORTID(port); c.nmac = nmac - 1; ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); if (ret) return ret; if (mac) { memcpy(mac, c.mac, sizeof(c.mac)); switch (nmac) { case 5: memcpy(mac + 24, c.nmac3, sizeof(c.nmac3)); /* FALLTHROUGH */ case 4: memcpy(mac + 18, c.nmac2, sizeof(c.nmac2)); /* FALLTHROUGH */ case 3: memcpy(mac + 12, c.nmac1, sizeof(c.nmac1)); /* FALLTHROUGH */ case 2: memcpy(mac + 6, c.nmac0, sizeof(c.nmac0)); /* FALLTHROUGH */ } } if (rss_size) *rss_size = G_FW_VI_CMD_RSSSIZE(be16_to_cpu(c.norss_rsssize)); return G_FW_VI_CMD_VIID(cpu_to_be16(c.type_to_viid)); } /** * t4_alloc_vi - allocate an [Ethernet Function] virtual interface * @adap: the adapter * @mbox: mailbox to use for the FW command * @port: physical port associated with the VI * @pf: the PF owning the VI * @vf: the VF owning the VI * @nmac: number of MAC addresses needed (1 to 5) * @mac: the MAC addresses of the VI * @rss_size: size of RSS table slice associated with this VI * * Backwards compatible and convieniance routine to allocate a Virtual * Interface with a Ethernet Port Application Function and Intrustion * Detection System disabled. */ int t4_alloc_vi(struct adapter *adap, unsigned int mbox, unsigned int port, unsigned int pf, unsigned int vf, unsigned int nmac, u8 *mac, unsigned int *rss_size) { return t4_alloc_vi_func(adap, mbox, port, pf, vf, nmac, mac, rss_size, FW_VI_FUNC_ETH, 0); } /** * t4_free_vi - free a virtual interface * @adap: the adapter * @mbox: mailbox to use for the FW command * @pf: the PF owning the VI * @vf: the VF owning the VI * @viid: virtual interface identifiler * * Free a previously allocated virtual interface. */ int t4_free_vi(struct adapter *adap, unsigned int mbox, unsigned int pf, unsigned int vf, unsigned int viid) { struct fw_vi_cmd c; memset(&c, 0, sizeof(c)); c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_VI_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_EXEC | V_FW_VI_CMD_PFN(pf) | V_FW_VI_CMD_VFN(vf)); c.alloc_to_len16 = cpu_to_be32(F_FW_VI_CMD_FREE | FW_LEN16(c)); c.type_to_viid = cpu_to_be16(V_FW_VI_CMD_VIID(viid)); return t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); } /** * t4_set_rxmode - set Rx properties of a virtual interface * @adap: the adapter * @mbox: mailbox to use for the FW command * @viid: the VI id * @mtu: the new MTU or -1 * @promisc: 1 to enable promiscuous mode, 0 to disable it, -1 no change * @all_multi: 1 to enable all-multi mode, 0 to disable it, -1 no change * @bcast: 1 to enable broadcast Rx, 0 to disable it, -1 no change * @vlanex: 1 to enable hardware VLAN Tag extraction, 0 to disable it, * -1 no change * @sleep_ok: if true we may sleep while awaiting command completion * * Sets Rx properties of a virtual interface. */ int t4_set_rxmode(struct adapter *adap, unsigned int mbox, unsigned int viid, int mtu, int promisc, int all_multi, int bcast, int vlanex, bool sleep_ok) { struct fw_vi_rxmode_cmd c; /* convert to FW values */ if (mtu < 0) mtu = M_FW_VI_RXMODE_CMD_MTU; if (promisc < 0) promisc = M_FW_VI_RXMODE_CMD_PROMISCEN; if (all_multi < 0) all_multi = M_FW_VI_RXMODE_CMD_ALLMULTIEN; if (bcast < 0) bcast = M_FW_VI_RXMODE_CMD_BROADCASTEN; if (vlanex < 0) vlanex = M_FW_VI_RXMODE_CMD_VLANEXEN; memset(&c, 0, sizeof(c)); c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_RXMODE_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_WRITE | V_FW_VI_RXMODE_CMD_VIID(viid)); c.retval_len16 = cpu_to_be32(FW_LEN16(c)); c.mtu_to_vlanexen = cpu_to_be32(V_FW_VI_RXMODE_CMD_MTU(mtu) | V_FW_VI_RXMODE_CMD_PROMISCEN(promisc) | V_FW_VI_RXMODE_CMD_ALLMULTIEN(all_multi) | V_FW_VI_RXMODE_CMD_BROADCASTEN(bcast) | V_FW_VI_RXMODE_CMD_VLANEXEN(vlanex)); return t4_wr_mbox_meat(adap, mbox, &c, sizeof(c), NULL, sleep_ok); } /** * t4_change_mac - modifies the exact-match filter for a MAC address * @adap: the adapter * @mbox: mailbox to use for the FW command * @viid: the VI id * @idx: index of existing filter for old value of MAC address, or -1 * @addr: the new MAC address value * @persist: whether a new MAC allocation should be persistent * @add_smt: if true also add the address to the HW SMT * * Modifies an exact-match filter and sets it to the new MAC address if * @idx >= 0, or adds the MAC address to a new filter if @idx < 0. In the * latter case the address is added persistently if @persist is %true. * * Note that in general it is not possible to modify the value of a given * filter so the generic way to modify an address filter is to free the one * being used by the old address value and allocate a new filter for the * new address value. * * Returns a negative error number or the index of the filter with the new * MAC value. Note that this index may differ from @idx. */ int t4_change_mac(struct adapter *adap, unsigned int mbox, unsigned int viid, int idx, const u8 *addr, bool persist, bool add_smt) { int ret, mode; struct fw_vi_mac_cmd c; struct fw_vi_mac_exact *p = c.u.exact; int max_mac_addr = adap->params.arch.mps_tcam_size; if (idx < 0) /* new allocation */ idx = persist ? FW_VI_MAC_ADD_PERSIST_MAC : FW_VI_MAC_ADD_MAC; mode = add_smt ? FW_VI_MAC_SMT_AND_MPSTCAM : FW_VI_MAC_MPS_TCAM_ENTRY; memset(&c, 0, sizeof(c)); c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_MAC_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_WRITE | V_FW_VI_MAC_CMD_VIID(viid)); c.freemacs_to_len16 = cpu_to_be32(V_FW_CMD_LEN16(1)); p->valid_to_idx = cpu_to_be16(F_FW_VI_MAC_CMD_VALID | V_FW_VI_MAC_CMD_SMAC_RESULT(mode) | V_FW_VI_MAC_CMD_IDX(idx)); memcpy(p->macaddr, addr, sizeof(p->macaddr)); ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); if (ret == 0) { ret = G_FW_VI_MAC_CMD_IDX(be16_to_cpu(p->valid_to_idx)); if (ret >= max_mac_addr) ret = -ENOMEM; } return ret; } /** * t4_enable_vi_params - enable/disable a virtual interface * @adap: the adapter * @mbox: mailbox to use for the FW command * @viid: the VI id * @rx_en: 1=enable Rx, 0=disable Rx * @tx_en: 1=enable Tx, 0=disable Tx * @dcb_en: 1=enable delivery of Data Center Bridging messages. * * Enables/disables a virtual interface. Note that setting DCB Enable * only makes sense when enabling a Virtual Interface ... */ int t4_enable_vi_params(struct adapter *adap, unsigned int mbox, unsigned int viid, bool rx_en, bool tx_en, bool dcb_en) { struct fw_vi_enable_cmd c; memset(&c, 0, sizeof(c)); c.op_to_viid = cpu_to_be32(V_FW_CMD_OP(FW_VI_ENABLE_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_EXEC | V_FW_VI_ENABLE_CMD_VIID(viid)); c.ien_to_len16 = cpu_to_be32(V_FW_VI_ENABLE_CMD_IEN(rx_en) | V_FW_VI_ENABLE_CMD_EEN(tx_en) | V_FW_VI_ENABLE_CMD_DCB_INFO(dcb_en) | FW_LEN16(c)); return t4_wr_mbox_ns(adap, mbox, &c, sizeof(c), NULL); } /** * t4_enable_vi - enable/disable a virtual interface * @adap: the adapter * @mbox: mailbox to use for the FW command * @viid: the VI id * @rx_en: 1=enable Rx, 0=disable Rx * @tx_en: 1=enable Tx, 0=disable Tx * * Enables/disables a virtual interface. Note that setting DCB Enable * only makes sense when enabling a Virtual Interface ... */ int t4_enable_vi(struct adapter *adap, unsigned int mbox, unsigned int viid, bool rx_en, bool tx_en) { return t4_enable_vi_params(adap, mbox, viid, rx_en, tx_en, 0); } /** * t4_iq_start_stop - enable/disable an ingress queue and its FLs * @adap: the adapter * @mbox: mailbox to use for the FW command * @start: %true to enable the queues, %false to disable them * @pf: the PF owning the queues * @vf: the VF owning the queues * @iqid: ingress queue id * @fl0id: FL0 queue id or 0xffff if no attached FL0 * @fl1id: FL1 queue id or 0xffff if no attached FL1 * * Starts or stops an ingress queue and its associated FLs, if any. */ int t4_iq_start_stop(struct adapter *adap, unsigned int mbox, bool start, unsigned int pf, unsigned int vf, unsigned int iqid, unsigned int fl0id, unsigned int fl1id) { struct fw_iq_cmd c; memset(&c, 0, sizeof(c)); c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_IQ_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_EXEC | V_FW_IQ_CMD_PFN(pf) | V_FW_IQ_CMD_VFN(vf)); c.alloc_to_len16 = cpu_to_be32(V_FW_IQ_CMD_IQSTART(start) | V_FW_IQ_CMD_IQSTOP(!start) | FW_LEN16(c)); c.iqid = cpu_to_be16(iqid); c.fl0id = cpu_to_be16(fl0id); c.fl1id = cpu_to_be16(fl1id); return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /** * t4_iq_free - free an ingress queue and its FLs * @adap: the adapter * @mbox: mailbox to use for the FW command * @pf: the PF owning the queues * @vf: the VF owning the queues * @iqtype: the ingress queue type (FW_IQ_TYPE_FL_INT_CAP, etc.) * @iqid: ingress queue id * @fl0id: FL0 queue id or 0xffff if no attached FL0 * @fl1id: FL1 queue id or 0xffff if no attached FL1 * * Frees an ingress queue and its associated FLs, if any. */ int t4_iq_free(struct adapter *adap, unsigned int mbox, unsigned int pf, unsigned int vf, unsigned int iqtype, unsigned int iqid, unsigned int fl0id, unsigned int fl1id) { struct fw_iq_cmd c; memset(&c, 0, sizeof(c)); c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_IQ_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_EXEC | V_FW_IQ_CMD_PFN(pf) | V_FW_IQ_CMD_VFN(vf)); c.alloc_to_len16 = cpu_to_be32(F_FW_IQ_CMD_FREE | FW_LEN16(c)); c.type_to_iqandstindex = cpu_to_be32(V_FW_IQ_CMD_TYPE(iqtype)); c.iqid = cpu_to_be16(iqid); c.fl0id = cpu_to_be16(fl0id); c.fl1id = cpu_to_be16(fl1id); return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /** * t4_eth_eq_free - free an Ethernet egress queue * @adap: the adapter * @mbox: mailbox to use for the FW command * @pf: the PF owning the queue * @vf: the VF owning the queue * @eqid: egress queue id * * Frees an Ethernet egress queue. */ int t4_eth_eq_free(struct adapter *adap, unsigned int mbox, unsigned int pf, unsigned int vf, unsigned int eqid) { struct fw_eq_eth_cmd c; memset(&c, 0, sizeof(c)); c.op_to_vfn = cpu_to_be32(V_FW_CMD_OP(FW_EQ_ETH_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_EXEC | V_FW_EQ_ETH_CMD_PFN(pf) | V_FW_EQ_ETH_CMD_VFN(vf)); c.alloc_to_len16 = cpu_to_be32(F_FW_EQ_ETH_CMD_FREE | FW_LEN16(c)); c.eqid_pkd = cpu_to_be32(V_FW_EQ_ETH_CMD_EQID(eqid)); return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } /** * t4_handle_fw_rpl - process a FW reply message * @adap: the adapter * @rpl: start of the FW message * * Processes a FW message, such as link state change messages. */ int t4_handle_fw_rpl(struct adapter *adap, const __be64 *rpl) { u8 opcode = *(const u8 *)rpl; /* * This might be a port command ... this simplifies the following * conditionals ... We can get away with pre-dereferencing * action_to_len16 because it's in the first 16 bytes and all messages * will be at least that long. */ const struct fw_port_cmd *p = (const void *)rpl; unsigned int action = G_FW_PORT_CMD_ACTION(be32_to_cpu(p->action_to_len16)); if (opcode == FW_PORT_CMD && action == FW_PORT_ACTION_GET_PORT_INFO) { /* link/module state change message */ int speed = 0, fc = 0, i; int chan = G_FW_PORT_CMD_PORTID(be32_to_cpu(p->op_to_portid)); struct port_info *pi = NULL; struct link_config *lc; u32 stat = be32_to_cpu(p->u.info.lstatus_to_modtype); int link_ok = (stat & F_FW_PORT_CMD_LSTATUS) != 0; u32 mod = G_FW_PORT_CMD_MODTYPE(stat); if (stat & F_FW_PORT_CMD_RXPAUSE) fc |= PAUSE_RX; if (stat & F_FW_PORT_CMD_TXPAUSE) fc |= PAUSE_TX; if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_100M)) speed = ETH_SPEED_NUM_100M; else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_1G)) speed = ETH_SPEED_NUM_1G; else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_10G)) speed = ETH_SPEED_NUM_10G; else if (stat & V_FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_40G)) speed = ETH_SPEED_NUM_40G; for_each_port(adap, i) { pi = adap2pinfo(adap, i); if (pi->tx_chan == chan) break; } lc = &pi->link_cfg; if (mod != pi->mod_type) { pi->mod_type = mod; t4_os_portmod_changed(adap, i); } if (link_ok != lc->link_ok || speed != lc->speed || fc != lc->fc) { /* something changed */ if (!link_ok && lc->link_ok) { static const char * const reason[] = { "Link Down", "Remote Fault", "Auto-negotiation Failure", "Reserved", "Insufficient Airflow", "Unable To Determine Reason", "No RX Signal Detected", "Reserved", }; unsigned int rc = G_FW_PORT_CMD_LINKDNRC(stat); dev_warn(adap, "Port %d link down, reason: %s\n", chan, reason[rc]); } lc->link_ok = link_ok; lc->speed = speed; lc->fc = fc; lc->supported = be16_to_cpu(p->u.info.pcap); } } else { dev_warn(adap, "Unknown firmware reply %d\n", opcode); return -EINVAL; } return 0; } void t4_reset_link_config(struct adapter *adap, int idx) { struct port_info *pi = adap2pinfo(adap, idx); struct link_config *lc = &pi->link_cfg; lc->link_ok = 0; lc->requested_speed = 0; lc->requested_fc = 0; lc->speed = 0; lc->fc = 0; } /** * init_link_config - initialize a link's SW state * @lc: structure holding the link state * @caps: link capabilities * * Initializes the SW state maintained for each link, including the link's * capabilities and default speed/flow-control/autonegotiation settings. */ static void init_link_config(struct link_config *lc, unsigned int caps) { lc->supported = caps; lc->requested_speed = 0; lc->speed = 0; lc->requested_fc = 0; lc->fc = 0; if (lc->supported & FW_PORT_CAP_ANEG) { lc->advertising = lc->supported & ADVERT_MASK; lc->autoneg = AUTONEG_ENABLE; } else { lc->advertising = 0; lc->autoneg = AUTONEG_DISABLE; } } /** * t4_wait_dev_ready - wait till to reads of registers work * * Right after the device is RESET is can take a small amount of time * for it to respond to register reads. Until then, all reads will * return either 0xff...ff or 0xee...ee. Return an error if reads * don't work within a reasonable time frame. */ static int t4_wait_dev_ready(struct adapter *adapter) { u32 whoami; whoami = t4_read_reg(adapter, A_PL_WHOAMI); if (whoami != 0xffffffff && whoami != X_CIM_PF_NOACCESS) return 0; msleep(500); whoami = t4_read_reg(adapter, A_PL_WHOAMI); return (whoami != 0xffffffff && whoami != X_CIM_PF_NOACCESS ? 0 : -EIO); } struct flash_desc { u32 vendor_and_model_id; u32 size_mb; }; int t4_get_flash_params(struct adapter *adapter) { /* * Table for non-Numonix supported flash parts. Numonix parts are left * to the preexisting well-tested code. All flash parts have 64KB * sectors. */ static struct flash_desc supported_flash[] = { { 0x150201, 4 << 20 }, /* Spansion 4MB S25FL032P */ }; int ret; unsigned int i; u32 info = 0; ret = sf1_write(adapter, 1, 1, 0, SF_RD_ID); if (!ret) ret = sf1_read(adapter, 3, 0, 1, &info); t4_write_reg(adapter, A_SF_OP, 0); /* unlock SF */ if (ret < 0) return ret; for (i = 0; i < ARRAY_SIZE(supported_flash); ++i) if (supported_flash[i].vendor_and_model_id == info) { adapter->params.sf_size = supported_flash[i].size_mb; adapter->params.sf_nsec = adapter->params.sf_size / SF_SEC_SIZE; return 0; } if ((info & 0xff) != 0x20) /* not a Numonix flash */ return -EINVAL; info >>= 16; /* log2 of size */ if (info >= 0x14 && info < 0x18) adapter->params.sf_nsec = 1 << (info - 16); else if (info == 0x18) adapter->params.sf_nsec = 64; else return -EINVAL; adapter->params.sf_size = 1 << info; /* * We should reject adapters with FLASHes which are too small. So, emit * a warning. */ if (adapter->params.sf_size < FLASH_MIN_SIZE) { dev_warn(adapter, "WARNING!!! FLASH size %#x < %#x!!!\n", adapter->params.sf_size, FLASH_MIN_SIZE); } return 0; } /** * t4_prep_adapter - prepare SW and HW for operation * @adapter: the adapter * * Initialize adapter SW state for the various HW modules, set initial * values for some adapter tunables, take PHYs out of reset, and * initialize the MDIO interface. */ int t4_prep_adapter(struct adapter *adapter) { int ret, ver; u32 pl_rev; ret = t4_wait_dev_ready(adapter); if (ret < 0) return ret; pl_rev = G_REV(t4_read_reg(adapter, A_PL_REV)); adapter->params.pci.device_id = adapter->pdev->id.device_id; adapter->params.pci.vendor_id = adapter->pdev->id.vendor_id; /* * WE DON'T NEED adapter->params.chip CODE ONCE PL_REV CONTAINS * ADAPTER (VERSION << 4 | REVISION) */ ver = CHELSIO_PCI_ID_VER(adapter->params.pci.device_id); adapter->params.chip = 0; switch (ver) { case CHELSIO_T5: adapter->params.chip |= CHELSIO_CHIP_CODE(CHELSIO_T5, pl_rev); adapter->params.arch.sge_fl_db = F_DBPRIO | F_DBTYPE; adapter->params.arch.mps_tcam_size = NUM_MPS_T5_CLS_SRAM_L_INSTANCES; adapter->params.arch.mps_rplc_size = 128; adapter->params.arch.nchan = NCHAN; adapter->params.arch.vfcount = 128; break; default: dev_err(adapter, "%s: Device %d is not supported\n", __func__, adapter->params.pci.device_id); return -EINVAL; } ret = t4_get_flash_params(adapter); if (ret < 0) return ret; adapter->params.cim_la_size = CIMLA_SIZE; init_cong_ctrl(adapter->params.a_wnd, adapter->params.b_wnd); /* * Default port and clock for debugging in case we can't reach FW. */ adapter->params.nports = 1; adapter->params.portvec = 1; adapter->params.vpd.cclk = 50000; return 0; } /** * t4_bar2_sge_qregs - return BAR2 SGE Queue register information * @adapter: the adapter * @qid: the Queue ID * @qtype: the Ingress or Egress type for @qid * @pbar2_qoffset: BAR2 Queue Offset * @pbar2_qid: BAR2 Queue ID or 0 for Queue ID inferred SGE Queues * * Returns the BAR2 SGE Queue Registers information associated with the * indicated Absolute Queue ID. These are passed back in return value * pointers. @qtype should be T4_BAR2_QTYPE_EGRESS for Egress Queue * and T4_BAR2_QTYPE_INGRESS for Ingress Queues. * * This may return an error which indicates that BAR2 SGE Queue * registers aren't available. If an error is not returned, then the * following values are returned: * * *@pbar2_qoffset: the BAR2 Offset of the @qid Registers * *@pbar2_qid: the BAR2 SGE Queue ID or 0 of @qid * * If the returned BAR2 Queue ID is 0, then BAR2 SGE registers which * require the "Inferred Queue ID" ability may be used. E.g. the * Write Combining Doorbell Buffer. If the BAR2 Queue ID is not 0, * then these "Inferred Queue ID" register may not be used. */ int t4_bar2_sge_qregs(struct adapter *adapter, unsigned int qid, enum t4_bar2_qtype qtype, u64 *pbar2_qoffset, unsigned int *pbar2_qid) { unsigned int page_shift, page_size, qpp_shift, qpp_mask; u64 bar2_page_offset, bar2_qoffset; unsigned int bar2_qid, bar2_qid_offset, bar2_qinferred; /* * T4 doesn't support BAR2 SGE Queue registers. */ if (is_t4(adapter->params.chip)) return -EINVAL; /* * Get our SGE Page Size parameters. */ page_shift = adapter->params.sge.hps + 10; page_size = 1 << page_shift; /* * Get the right Queues per Page parameters for our Queue. */ qpp_shift = (qtype == T4_BAR2_QTYPE_EGRESS ? adapter->params.sge.eq_qpp : adapter->params.sge.iq_qpp); qpp_mask = (1 << qpp_shift) - 1; /* * Calculate the basics of the BAR2 SGE Queue register area: * o The BAR2 page the Queue registers will be in. * o The BAR2 Queue ID. * o The BAR2 Queue ID Offset into the BAR2 page. */ bar2_page_offset = ((qid >> qpp_shift) << page_shift); bar2_qid = qid & qpp_mask; bar2_qid_offset = bar2_qid * SGE_UDB_SIZE; /* * If the BAR2 Queue ID Offset is less than the Page Size, then the * hardware will infer the Absolute Queue ID simply from the writes to * the BAR2 Queue ID Offset within the BAR2 Page (and we need to use a * BAR2 Queue ID of 0 for those writes). Otherwise, we'll simply * write to the first BAR2 SGE Queue Area within the BAR2 Page with * the BAR2 Queue ID and the hardware will infer the Absolute Queue ID * from the BAR2 Page and BAR2 Queue ID. * * One important censequence of this is that some BAR2 SGE registers * have a "Queue ID" field and we can write the BAR2 SGE Queue ID * there. But other registers synthesize the SGE Queue ID purely * from the writes to the registers -- the Write Combined Doorbell * Buffer is a good example. These BAR2 SGE Registers are only * available for those BAR2 SGE Register areas where the SGE Absolute * Queue ID can be inferred from simple writes. */ bar2_qoffset = bar2_page_offset; bar2_qinferred = (bar2_qid_offset < page_size); if (bar2_qinferred) { bar2_qoffset += bar2_qid_offset; bar2_qid = 0; } *pbar2_qoffset = bar2_qoffset; *pbar2_qid = bar2_qid; return 0; } /** * t4_init_sge_params - initialize adap->params.sge * @adapter: the adapter * * Initialize various fields of the adapter's SGE Parameters structure. */ int t4_init_sge_params(struct adapter *adapter) { struct sge_params *sge_params = &adapter->params.sge; u32 hps, qpp; unsigned int s_hps, s_qpp; /* * Extract the SGE Page Size for our PF. */ hps = t4_read_reg(adapter, A_SGE_HOST_PAGE_SIZE); s_hps = (S_HOSTPAGESIZEPF0 + (S_HOSTPAGESIZEPF1 - S_HOSTPAGESIZEPF0) * adapter->pf); sge_params->hps = ((hps >> s_hps) & M_HOSTPAGESIZEPF0); /* * Extract the SGE Egress and Ingess Queues Per Page for our PF. */ s_qpp = (S_QUEUESPERPAGEPF0 + (S_QUEUESPERPAGEPF1 - S_QUEUESPERPAGEPF0) * adapter->pf); qpp = t4_read_reg(adapter, A_SGE_EGRESS_QUEUES_PER_PAGE_PF); sge_params->eq_qpp = ((qpp >> s_qpp) & M_QUEUESPERPAGEPF0); qpp = t4_read_reg(adapter, A_SGE_INGRESS_QUEUES_PER_PAGE_PF); sge_params->iq_qpp = ((qpp >> s_qpp) & M_QUEUESPERPAGEPF0); return 0; } /** * t4_init_tp_params - initialize adap->params.tp * @adap: the adapter * * Initialize various fields of the adapter's TP Parameters structure. */ int t4_init_tp_params(struct adapter *adap) { int chan; u32 v; v = t4_read_reg(adap, A_TP_TIMER_RESOLUTION); adap->params.tp.tre = G_TIMERRESOLUTION(v); adap->params.tp.dack_re = G_DELAYEDACKRESOLUTION(v); /* MODQ_REQ_MAP defaults to setting queues 0-3 to chan 0-3 */ for (chan = 0; chan < NCHAN; chan++) adap->params.tp.tx_modq[chan] = chan; /* * Cache the adapter's Compressed Filter Mode and global Incress * Configuration. */ t4_read_indirect(adap, A_TP_PIO_ADDR, A_TP_PIO_DATA, &adap->params.tp.vlan_pri_map, 1, A_TP_VLAN_PRI_MAP); t4_read_indirect(adap, A_TP_PIO_ADDR, A_TP_PIO_DATA, &adap->params.tp.ingress_config, 1, A_TP_INGRESS_CONFIG); /* * Now that we have TP_VLAN_PRI_MAP cached, we can calculate the field * shift positions of several elements of the Compressed Filter Tuple * for this adapter which we need frequently ... */ adap->params.tp.vlan_shift = t4_filter_field_shift(adap, F_VLAN); adap->params.tp.vnic_shift = t4_filter_field_shift(adap, F_VNIC_ID); adap->params.tp.port_shift = t4_filter_field_shift(adap, F_PORT); adap->params.tp.protocol_shift = t4_filter_field_shift(adap, F_PROTOCOL); /* * If TP_INGRESS_CONFIG.VNID == 0, then TP_VLAN_PRI_MAP.VNIC_ID * represents the presense of an Outer VLAN instead of a VNIC ID. */ if ((adap->params.tp.ingress_config & F_VNIC) == 0) adap->params.tp.vnic_shift = -1; return 0; } /** * t4_filter_field_shift - calculate filter field shift * @adap: the adapter * @filter_sel: the desired field (from TP_VLAN_PRI_MAP bits) * * Return the shift position of a filter field within the Compressed * Filter Tuple. The filter field is specified via its selection bit * within TP_VLAN_PRI_MAL (filter mode). E.g. F_VLAN. */ int t4_filter_field_shift(const struct adapter *adap, unsigned int filter_sel) { unsigned int filter_mode = adap->params.tp.vlan_pri_map; unsigned int sel; int field_shift; if ((filter_mode & filter_sel) == 0) return -1; for (sel = 1, field_shift = 0; sel < filter_sel; sel <<= 1) { switch (filter_mode & sel) { case F_FCOE: field_shift += W_FT_FCOE; break; case F_PORT: field_shift += W_FT_PORT; break; case F_VNIC_ID: field_shift += W_FT_VNIC_ID; break; case F_VLAN: field_shift += W_FT_VLAN; break; case F_TOS: field_shift += W_FT_TOS; break; case F_PROTOCOL: field_shift += W_FT_PROTOCOL; break; case F_ETHERTYPE: field_shift += W_FT_ETHERTYPE; break; case F_MACMATCH: field_shift += W_FT_MACMATCH; break; case F_MPSHITTYPE: field_shift += W_FT_MPSHITTYPE; break; case F_FRAGMENTATION: field_shift += W_FT_FRAGMENTATION; break; } } return field_shift; } int t4_init_rss_mode(struct adapter *adap, int mbox) { int i, ret; struct fw_rss_vi_config_cmd rvc; memset(&rvc, 0, sizeof(rvc)); for_each_port(adap, i) { struct port_info *p = adap2pinfo(adap, i); rvc.op_to_viid = htonl(V_FW_CMD_OP(FW_RSS_VI_CONFIG_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_READ | V_FW_RSS_VI_CONFIG_CMD_VIID(p->viid)); rvc.retval_len16 = htonl(FW_LEN16(rvc)); ret = t4_wr_mbox(adap, mbox, &rvc, sizeof(rvc), &rvc); if (ret) return ret; p->rss_mode = ntohl(rvc.u.basicvirtual.defaultq_to_udpen); } return 0; } int t4_port_init(struct adapter *adap, int mbox, int pf, int vf) { u8 addr[6]; int ret, i, j = 0; struct fw_port_cmd c; memset(&c, 0, sizeof(c)); for_each_port(adap, i) { unsigned int rss_size = 0; struct port_info *p = adap2pinfo(adap, i); while ((adap->params.portvec & (1 << j)) == 0) j++; c.op_to_portid = cpu_to_be32(V_FW_CMD_OP(FW_PORT_CMD) | F_FW_CMD_REQUEST | F_FW_CMD_READ | V_FW_PORT_CMD_PORTID(j)); c.action_to_len16 = cpu_to_be32(V_FW_PORT_CMD_ACTION( FW_PORT_ACTION_GET_PORT_INFO) | FW_LEN16(c)); ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); if (ret) return ret; ret = t4_alloc_vi(adap, mbox, j, pf, vf, 1, addr, &rss_size); if (ret < 0) return ret; p->viid = ret; p->tx_chan = j; p->rss_size = rss_size; t4_os_set_hw_addr(adap, i, addr); ret = be32_to_cpu(c.u.info.lstatus_to_modtype); p->mdio_addr = (ret & F_FW_PORT_CMD_MDIOCAP) ? G_FW_PORT_CMD_MDIOADDR(ret) : -1; p->port_type = G_FW_PORT_CMD_PTYPE(ret); p->mod_type = FW_PORT_MOD_TYPE_NA; init_link_config(&p->link_cfg, be16_to_cpu(c.u.info.pcap)); j++; } return 0; }