-.. BSD LICENSE
- Copyright 2016 NXP.
-
- Redistribution and use in source and binary forms, with or without
- modification, are permitted provided that the following conditions
- are met:
-
- * Redistributions of source code must retain the above copyright
- notice, this list of conditions and the following disclaimer.
- * Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in
- the documentation and/or other materials provided with the
- distribution.
- * Neither the name of NXP nor the names of its
- contributors may be used to endorse or promote products derived
- from this software without specific prior written permission.
-
- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright 2016 NXP
+
NXP DPAA2 CAAM (DPAA2_SEC)
Supported DPAA2 SoCs
--------------------
-* LS2080A/LS2040A
+* LS2160A
* LS2084A/LS2044A
* LS2088A/LS2048A
* LS1088A/LS1048A
+Whitelisting & Blacklisting
+---------------------------
+
+For blacklisting a DPAA2 SEC device, following commands can be used.
+
+ .. code-block:: console
+
+ <dpdk app> <EAL args> -b "fslmc:dpseci.x" -- ...
+
+Where x is the device object id as configured in resource container.
+
Limitations
-----------
-* Chained mbufs are not supported.
* Hash followed by Cipher mode is not supported
* Only supports the session-oriented API implementation (session-less APIs are not supported).
DPAA2_SEC driver has similar pre-requisites as described in :ref:`dpaa2_overview`.
The following dependencies are not part of DPDK and must be installed separately:
-* **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for the family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK helper repository.
-
- `DPDK Extra Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-* NXP SDK **17.08+**.
-* MC Firmware version **10.3.1** and higher.
-* Supported architectures: **arm64 LE**.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures: **arm64 LE**.
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
Pre-Installation Configuration
------------------------------
By default it is only enabled in defconfig_arm64-dpaa2-* config.
Toggle compilation of the ``librte_pmd_dpaa2_sec`` driver.
-* ``CONFIG_RTE_LIBRTE_DPAA2_SEC_DEBUG_INIT`` (default ``n``)
- Toggle display of initialization related driver messages
-
-* ``CONFIG_RTE_LIBRTE_DPAA2_SEC_DEBUG_DRIVER`` (default ``n``)
- Toggle display of driver runtime messages
-
-* ``CONFIG_RTE_LIBRTE_DPAA2_SEC_DEBUG_RX`` (default ``n``)
- Toggle display of receive fast path run-time message
-
-* ``CONFIG_RTE_DPAA2_SEC_PMD_MAX_NB_SESSIONS``
- By default it is set as 2048 in defconfig_arm64-dpaa2-* config.
- It indicates Number of sessions to create in the session memory pool
- on a single DPAA2 SEC device.
-
Installations
-------------
To compile the DPAA2_SEC PMD for Linux arm64 gcc target, run the
cd <DPDK-source-directory>
make config T=arm64-dpaa2-linuxapp-gcc install
+
+Enabling logs
+-------------
+
+For enabling logs, use the following EAL parameter:
+
+.. code-block:: console
+
+ ./your_crypto_application <EAL args> --log-level=pmd.crypto.dpaa2:<level>
+
+Using ``crypto.dpaa2`` as log matching criteria, all Crypto PMD logs can be
+enabled which are lower than logging ``level``.
Code Review / deb_dpdk.git / blobdiff