Interrupt Throttling interval.
+Runtime Config Options
+~~~~~~~~~~~~~~~~~~~~~~
+
+- ``Support multiple driver`` (default ``disable``)
+
+ There was a multiple driver support issue during use of 700 series Ethernet
+ Adapter with both Linux kernel and DPDK PMD. To fix this issue, ``devargs``
+ parameter ``support-multi-driver`` is introduced, for example::
+
+ -w 84:00.0,support-multi-driver=1
+
+ With the above configuration, DPDK PMD will not change global registers, and
+ will switch PF interrupt from IntN to Int0 to avoid interrupt conflict between
+ DPDK and Linux Kernel.
+
Driver Compilation
~~~~~~~~~~~~~~~~~~
.. code-block:: console
- ./tools/dpdk_nic_bind.py --bind igb_uio 0000:83:00.0
+ ./tools/dpdk-devbind.py --bind igb_uio 0000:83:00.0
Or setup VFIO permissions for regular users and then bind to ``vfio-pci``:
.. code-block:: console
- ./tools/dpdk_nic_bind.py --bind vfio-pci 0000:83:00.0
+ ./tools/dpdk-devbind.py --bind vfio-pci 0000:83:00.0
#. Start ``testpmd`` with basic parameters:
The floating VEB functionality requires a NIC firmware version of 5.0
or greater.
+
+
+Limitations or Known issues
+---------------------------
+
+MPLS packet classification on X710/XL710
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+For firmware versions prior to 5.0, MPLS packets are not recognized by the NIC.
+The L2 Payload flow type in flow director can be used to classify MPLS packet
+by using a command in testpmd like:
+
+ testpmd> flow_director_filter 0 mode IP add flow l2_payload ether \
+ 0x8847 flexbytes () fwd pf queue <N> fd_id <M>
+
+With the NIC firmware version 5.0 or greater, some limited MPLS support
+is added: Native MPLS (MPLS in Ethernet) skip is implemented, while no
+new packet type, no classification or offload are possible. With this change,
+L2 Payload flow type in flow director cannot be used to classify MPLS packet
+as with previous firmware versions. Meanwhile, the Ethertype filter can be
+used to classify MPLS packet by using a command in testpmd like:
+
+ testpmd> ethertype_filter 0 add mac_ignr 00:00:00:00:00:00 ethertype \
+ 0x8847 fwd queue <M>
+
+16 Byte Descriptor cannot be used on DPDK VF
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+If the Linux i40e kernel driver is used as host driver, while DPDK i40e PMD
+is used as the VF driver, DPDK cannot choose 16 byte receive descriptor. That
+is to say, user should keep ``CONFIG_RTE_LIBRTE_I40E_16BYTE_RX_DESC=n`` in
+config file.
+
+Link down with i40e kernel driver after DPDK application exist
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+After DPDK application quit, and the device is bound back to Linux i40e
+kernel driver, the link cannot be up after ``ifconfig <dev> up``.
+To work around this issue, ``ethtool -s <dev> autoneg on`` should be
+set first and then the link can be brought up through ``ifconfig <dev> up``.
+
+NOTE: requires Linux kernel i40e driver version >= 1.4.X
+
+Receive packets with Ethertype 0x88A8
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Due to the FW limitation, PF can receive packets with Ethertype 0x88A8
+only when floating VEB is disabled.
+
+Global configuration warning
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+I40E PMD will set some global registers to enable some function or set some
+configure. Then when using different ports of the same NIC with Linux kernel
+and DPDK, the port with Linux kernel will be impacted by the port with DPDK.
+For example, register I40E_GL_SWT_L2TAGCTRL is used to control L2 tag, i40e
+PMD uses I40E_GL_SWT_L2TAGCTRL to set vlan TPID. If setting TPID in port A
+with DPDK, then the configuration will also impact port B in the NIC with
+kernel driver, which don't want to use the TPID.
+So PMD reports warning to clarify what is changed by writing global register.
Code Review / deb_dpdk.git / blobdiff