-CSIT Release Notes\r
-==================\r
-\r
-Changes in CSIT |release|\r
--------------------------\r
-\r
-#. Added VPP performance tests\r
-\r
- - **Container Topologies Orchestrated by K8s with VPP memif tests**\r
-\r
- - Added tests with VPP in L2 Cross-Connect and Bridge-Domain\r
- configurations containers, with service chain topologies orchestrated by\r
- Kubernetes. Added following forwarding topologies: i) "Parallel" with\r
- packets flowing from NIC via VPP to container and back to VPP and NIC;\r
- ii) "Chained" a.k.a. "Snake" with packets flowing via VPP to container,\r
- back to VPP, to next container, back to VPP and so on until the last\r
- container in chain, then back to VPP and NIC; iii) "Horizontal" with\r
- packets flowing via VPP to container, then via "horizontal" memif to\r
- next container, and so on until the last container, then back to VPP and\r
- NIC;.\r
-\r
- - **VPP TCP/IP stack**\r
-\r
- - Added tests for VPP TCP/IP stack using VPP built-in HTTP server.\r
- WRK traffic generator is used as a client-side;\r
-\r
- - **SRv6 tests**\r
-\r
- - Initial SRv6 (Segment Routing IPv6) tests verifying performance of\r
- IPv6 and SRH (Segment Routing Header) encapsulation, decapsulation,\r
- lookups and rewrites based on configured End and End.DX6 SRv6 egress\r
- functions;\r
-\r
- - **IPSecSW tests**\r
-\r
- - SW computed IPSec encryption with AES-GCM, CBC-SHA1 ciphers, in\r
- combination with IPv4 routed-forwarding;\r
-\r
-#. Presentation and Analytics Layer\r
-\r
- - Added throughput speedup analysis for multi-core and multi-thread\r
- VPP tests into Presentation and Analytics Layer (PAL) for automated\r
- CSIT test results analysis;\r
-\r
-#. Other improvements\r
-\r
- - **Framework optimizations**\r
-\r
- - Ability to run CSIT framework on ARM architecture;\r
-\r
- - Overall stability improvements;\r
-\r
-Performance Changes\r
--------------------\r
-\r
-Substantial changes in measured packet throughput have been observed in a\r
-number of CSIT |release| tests listed below. Relative changes for this release\r
-are calculated against the test results listed in CSIT |release-1| report. The\r
-comparison is calculated between the mean values based on collected and\r
-archived test results' samples for involved VPP releases. Standard deviation\r
-has been also listed for CSIT |release|.\r
-\r
-NDR Throughput: Best 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: ../../../_build/_static/vpp/performance-changes-ndr-1t1c-top.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{5cm} m{#1} m{#1} m{#1} m{#1} m{#1}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_build/_static/vpp/performance-changes-ndr-1t1c-top.csv}\r
- }\r
-\r
-NDR Throughput: Worst 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: ../../../_build/_static/vpp/performance-changes-ndr-1t1c-bottom.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{6cm} m{#1} m{#1} m{#1} m{#1} m{#1}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_build/_static/vpp/performance-changes-ndr-1t1c-bottom.csv}\r
- }\r
-\r
-.. only:: html\r
-\r
- NDR Throughput: All Changes\r
- ~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
- Complete results for all NDR tests are available in a CSV and pretty\r
- ASCII formats:\r
-\r
- - `csv format for 1t1c <../_static/vpp/performance-changes-ndr-1t1c-full.csv>`_,\r
- - `csv format for 2t2c <../_static/vpp/performance-changes-ndr-2t2c-full.csv>`_,\r
- - `csv format for 4t4c <../_static/vpp/performance-changes-ndr-4t4c-full.csv>`_,\r
- - `pretty ASCII format for 1t1c <../_static/vpp/performance-changes-ndr-1t1c-full.txt>`_,\r
- - `pretty ASCII format for 2t2c <../_static/vpp/performance-changes-ndr-2t2c-full.txt>`_,\r
- - `pretty ASCII format for 4t4c <../_static/vpp/performance-changes-ndr-4t4c-full.txt>`_.\r
-\r
-PDR Throughput: Best 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: ../../../_build/_static/vpp/performance-changes-pdr-1t1c-top.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{5cm} m{#2} m{#2} m{#2} m{#2} m{#2}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_build/_static/vpp/performance-changes-pdr-1t1c-top.csv}\r
- }\r
-\r
-PDR Throughput: Worst 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: ../../../_build/_static/vpp/performance-changes-pdr-1t1c-bottom.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{6cm} m{#2} m{#2} m{#2} m{#2} m{#2}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_build/_static/vpp/performance-changes-pdr-1t1c-bottom.csv}\r
- }\r
-\r
-.. only:: html\r
-\r
- PDR Throughput: All Changes\r
- ~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
- Complete results for all PDR tests are available in a CSV and pretty\r
- ASCII formats:\r
-\r
- - `csv format for 1t1c <../_static/vpp/performance-changes-pdr-1t1c-full.csv>`_,\r
- - `csv format for 2t2c <../_static/vpp/performance-changes-pdr-2t2c-full.csv>`_,\r
- - `csv format for 4t4c <../_static/vpp/performance-changes-pdr-4t4c-full.csv>`_,\r
- - `pretty ASCII format for 1t1c <../_static/vpp/performance-changes-pdr-1t1c-full.txt>`_,\r
- - `pretty ASCII format for 2t2c <../_static/vpp/performance-changes-pdr-2t2c-full.txt>`_,\r
- - `pretty ASCII format for 4t4c <../_static/vpp/performance-changes-pdr-4t4c-full.txt>`_.\r
-\r
-Measured improvements are in line with VPP code optimizations listed in\r
-`VPP-17.10 release notes\r
-<https://docs.fd.io/vpp/17.10/release_notes_1710.html>`_.\r
-\r
-Known Issues\r
-------------\r
-\r
-Here is the list of known issues in CSIT |release| for VPP performance tests:\r
-\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| # | Issue | Jira ID | Description |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 1 | Vic1385 and Vic1227 low performance. | VPP-664 | Low NDR performance. |\r
-| | | | |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 2 | Sporadic NDR discovery test failures on x520. | CSIT-750 | Suspected issue with HW combination of X710-X520 in LF |\r
-| | | | infrastructure. Issue can't be replicated outside LF. |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 3 | VPP in 2t2c setups - large variation | CSIT-568 | Suspected NIC firmware or DPDK driver issue affecting NDR |\r
-| | of discovered NDR throughput values across | | throughput. Applies to XL710 and X710 NICs, x520 NICs are fine. |\r
-| | multiple test runs with xl710 and x710 NICs. | | |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 4 | Lower than expected NDR throughput with | CSIT-569 | Suspected NIC firmware or DPDK driver issue affecting NDR and |\r
-| | xl710 and x710 NICs, compared to x520 NICs. | | PDR throughput. Applies to XL710 and X710 NICs. |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
+Release Notes
+=============
+
+Changes in |csit-release|
+-------------------------
+
+#. VPP PERFORMANCE TESTS
+
+ - CSIT test environment is versioned, see
+ :ref:`test_environment_versioning`.
+
+ - To identify performance changes due to VPP code changes from
+ v20.05.0 to v20.09.0, both have been tested in CSIT environment
+ ver. 5 and compared against each other. All substantial
+ progressions has been marked up with RCA analysis. See
+ :ref:`vpp_compare_current_vs_previous_release` and
+ :ref:`vpp_known_issues`.
+
+ - **NAT44 tests**: Adapted existing and added new tests.
+
+ - Refactored NAT44 deterministic mode (nat44det) tests to use separate
+ det44 vpp plugin and to use the same scheme of inside and outside
+ addresses and ports, as used in new NAT44 endpoint-dependent mode tests.
+
+ - Added new NAT44 endpoint-depended mode uni-directional (nat44ed-udir)
+ tests that measure packet throughput in one direction with usage of TRex
+ in stateless mode.
+
+ - Added new NAT44 endpoint-dependent mode CPS tests that measure
+ connections per second with usage of TRex in stateful mode.
+ NOTE: CPS measurement data will be added in two weeks.
+
+ - **IPSec async mode tests**: Added VPP performance tests for async crypto
+ engine.
+
+ - **AMD 2n-zn2 testbed**: New physical testbed type installed in FD.io CSIT,
+ VPP performance data will be added in upcoming weeks.
+
+#. TEST FRAMEWORK
+
+ - **TRex ASTF**: Added capability to run TRex in advanced stateful mode.
+
+ - **CSIT PAPI support**: Due to issues with PAPI performance, VAT is
+ still used in CSIT for all VPP scale tests. See known issues below.
+
+ - **General Code Housekeeping**: Ongoing RF keywords optimizations,
+ removal of redundant RF keywords and aligning of suite/test
+ setup/teardowns.
+
+ - **Intel E810CQ 100G NIC**: Added configuration for Intel E810CQ 100G NIC.
+ No tests run for this NIC as it is not present in FD.io CSIT lab yet.
+
+#. PRESENTATION AND ANALYTICS LAYER
+
+ - **Graphs improvements**: Added possibility to use Gbps on Y-axis in
+ Packet Throughput and Speedup Multi-Core graphs, added unidirectional
+ mode to the Latency graphs.
+
+.. raw:: latex
+
+ \clearpage
+
+.. _vpp_known_issues:
+
+Known Issues
+------------
+
+List of known issues in |csit-release| for VPP performance tests:
+
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| # | JiraID | Issue Description |
++====+=========================================+===========================================================================================================+
+| 1 | `CSIT-570 | Sporadic (1 in 200) NDR discovery test failures on x520. DPDK reporting rx-errors, indicating L1 issue. |
+| | <https://jira.fd.io/browse/CSIT-570>`_ | Suspected issue with HW combination of X710-X520 in LF testbeds. Not observed outside of LF testbeds. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 2 | `VPP-662 | 9000B packets not supported by NICs VIC1227 and VIC1387. |
+| | <https://jira.fd.io/browse/VPP-662>`_ | |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 3 | `CSIT-1763 | Adapt ramp-up phase of nat44 tests for different frame sizes. |
+| | <https://jira.fd.io/browse/CSIT-1763>`_ | Currently ramp-up phase rate and duration values are correctly set for tests with 64B frame size. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 4 | `CSIT-1671 | All CSIT scale tests can not use PAPI due to much slower performance compared to VAT/CLI (it takes much |
+| | <https://jira.fd.io/browse/CSIT-1671>`_ | longer to program VPP). This needs to be addressed on the PAPI side. |
+| +-----------------------------------------+ The usual PAPI library spends too much time parsing arguments, so even with async processing (hundreds of |
+| | `VPP-1763 | commands in flight over socket), the VPP configuration for large scale tests (millions of messages) takes |
+| | <https://jira.fd.io/browse/VPP-1763>`_ | too long. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 5 | `VPP-1675 | IPv4 IPSEC 9000B packet tests are failing as no packet is forwarded. |
+| | <https://jira.fd.io/browse/VPP-1675>`_ | Reason: chained buffers are not supported. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 6 | `VPP-1934 | [i40e] Interfaces are not brought up from carrier-down. |
+| | <https://jira.fd.io/browse/VPP-1934>`_ | In case of i40e -based interface (e.g Intel x700 series NIC) is bound to kernel driver (i40e) and is in |
+| | | state "no-carrier" (<NO-CARRIER,BROADCAST,MULTICAST,UP>) because previously it was disabled via |
+| | | "I40E_AQ_PHY_LINK_ENABLED" call, then VPP during initialization of AVF interface is not re-enabling |
+| | | interface link via i40e driver to up. |
+| | | CSIT implemented `workaround for AVF interface <https://gerrit.fd.io/r/c/csit/+/29086>`_ until fixed. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 7 | `CSIT-1760 | All Mellanox / rdma driver tests are failing on LF testbed28 while successfully run on other LF testbeds. |
+| | <https://jira.fd.io/browse/CSIT-1760>`_ | |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+
+Root Cause Analysis for Performance Changes
+-------------------------------------------
+
+List of RCAs in |csit-release| for VPP performance changes:
+
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| # | JiraID | Issue Description |
++====+=========================================+===========================================================================================================+
+| 1 | | |
+| | | |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+