-CSIT Release Notes\r
-==================\r
-\r
-Changes in CSIT |release|\r
--------------------------\r
-\r
-#. Added VPP performance tests\r
-\r
- - **Container Topologies Orchestrated by K8s with VPP memif tests**\r
-\r
- - Added tests with VPP in L2 Cross-Connect and Bridge-Domain\r
- configurations containers, with service chain topologies orchestrated by\r
- Kubernetes. Added following forwarding topologies: i) "Parallel" with\r
- packets flowing from NIC via VPP to container and back to VPP and NIC;\r
- ii) "Chained" a.k.a. "Snake" with packets flowing via VPP to container,\r
- back to VPP, to next container, back to VPP and so on until the last\r
- container in chain, then back to VPP and NIC; iii) "Horizontal" with\r
- packets flowing via VPP to container, then via "horizontal" memif to\r
- next container, and so on until the last container, then back to VPP and\r
- NIC;.\r
-\r
- - **VPP TCP/IP stack**\r
-\r
- - Added tests for VPP TCP/IP stack using VPP built-in HTTP server.\r
- WRK traffic generator is used as a client-side;\r
-\r
- - **SRv6 tests**\r
-\r
- - Initial SRv6 (Segment Routing IPv6) tests verifying performance of\r
- IPv6 and SRH (Segment Routing Header) encapsulation, decapsulation,\r
- lookups and rewrites based on configured End and End.DX6 SRv6 egress\r
- functions;\r
-\r
- - **IPSecSW tests**\r
-\r
- - SW computed IPSec encryption with AES-GCM, CBC-SHA1 ciphers, in\r
- combination with IPv4 routed-forwarding;\r
-\r
-#. Presentation and Analytics Layer\r
-\r
- - Added throughput speedup analysis for multi-core and multi-thread\r
- VPP tests into Presentation and Analytics Layer (PAL) for automated\r
- CSIT test results analysis;\r
-\r
-#. Other improvements\r
-\r
- - **Framework optimizations**\r
-\r
- - Ability to run CSIT framework on ARM architecture;\r
-\r
- - Overall stability improvements;\r
-\r
-Performance Changes\r
--------------------\r
-\r
-Substantial changes in measured packet throughput have been observed in a\r
-number of CSIT |release| tests listed below. Relative changes for this release\r
-are calculated against the test results listed in CSIT |release-1| report. The\r
-comparison is calculated between the mean values based on collected and\r
-archived test results' samples for involved VPP releases. Standard deviation\r
-has been also listed for CSIT |release|.\r
-\r
-NDR Throughput: Best 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: performance_improvements/performance-changes-ndr-1t1c-top.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{4cm} m{#1} m{#1} m{#1} m{#1} m{#1}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_tmp/src/vpp_performance_tests/performance_improvements/performance-changes-ndr-1t1c-top.csv}\r
- }\r
-\r
-NDR Throughput: Worst 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: performance_improvements/performance-changes-ndr-1t1c-bottom.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{4cm} m{#1} m{#1} m{#1} m{#1} m{#1}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_tmp/src/vpp_performance_tests/performance_improvements/performance-changes-ndr-1t1c-bottom.csv}\r
- }\r
-\r
-.. only:: html\r
-\r
- NDR Throughput: All Changes\r
- ~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
- Complete results for all NDR tests are available in a CSV and pretty\r
- ASCII formats:\r
-\r
- - `csv format for 1t1c <performance_improvements/performance-changes-ndr-1t1c-full.csv>`_,\r
- - `csv format for 2t2c <performance_improvements/performance-changes-ndr-2t2c-full.csv>`_,\r
- - `csv format for 4t4c <performance_improvements/performance-changes-ndr-4t4c-full.csv>`_,\r
- - `pretty ASCII format for 1t1c <performance_improvements/performance-changes-ndr-1t1c-full.txt>`_,\r
- - `pretty ASCII format for 2t2c <performance_improvements/performance-changes-ndr-2t2c-full.txt>`_,\r
- - `pretty ASCII format for 4t4c <performance_improvements/performance-changes-ndr-4t4c-full.txt>`_.\r
-\r
-PDR Throughput: Best 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: performance_improvements/performance-changes-pdr-1t1c-top.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{4cm} m{#1} m{#1} m{#1} m{#1} m{#1}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_tmp/src/vpp_performance_tests/performance_improvements/performance-changes-pdr-1t1c-top.csv}\r
- }\r
-\r
-PDR Throughput: Worst 20 Changes\r
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
-.. only:: html\r
-\r
- .. csv-table::\r
- :align: center\r
- :file: performance_improvements/performance-changes-pdr-1t1c-bottom.csv\r
-\r
-.. only:: latex\r
-\r
- .. raw:: latex\r
-\r
- \makeatletter\r
- \csvset{\r
- perfimprovements column width/.style={after head=\csv@pretable\begin{longtable}{m{4cm} m{#1} m{#1} m{#1} m{#1} m{#1}}\csv@tablehead},\r
- }\r
- \makeatother\r
-\r
- {\tiny\r
- \csvautobooklongtable[separator=comma,\r
- respect all,\r
- no check column count,\r
- perfimprovements column width=1cm,\r
- late after line={\\\hline},\r
- late after last line={\end{longtable}}\r
- ]{../_tmp/src/vpp_performance_tests/performance_improvements/performance-changes-pdr-1t1c-bottom.csv}\r
- }\r
-\r
-.. only:: html\r
-\r
- PDR Throughput: All Changes\r
- ~~~~~~~~~~~~~~~~~~~~~~~~~~~\r
-\r
- Complete results for all PDR tests are available in a CSV and pretty\r
- ASCII formats:\r
-\r
- - `csv format for 1t1c <performance_improvements/performance-changes-pdr-1t1c-full.csv>`_,\r
- - `csv format for 2t2c <performance_improvements/performance-changes-pdr-2t2c-full.csv>`_,\r
- - `csv format for 4t4c <performance_improvements/performance-changes-pdr-4t4c-full.csv>`_,\r
- - `pretty ASCII format for 1t1c <performance_improvements/performance-changes-pdr-1t1c-full.txt>`_,\r
- - `pretty ASCII format for 2t2c <performance_improvements/performance-changes-pdr-2t2c-full.txt>`_,\r
- - `pretty ASCII format for 4t4c <performance_improvements/performance-changes-pdr-4t4c-full.txt>`_.\r
-\r
-Measured improvements are in line with VPP code optimizations listed in\r
-`VPP-17.10 release notes\r
-<https://docs.fd.io/vpp/17.10/release_notes_1710.html>`_.\r
-\r
-Known Issues\r
-------------\r
-\r
-Here is the list of known issues in CSIT |release| for VPP performance tests:\r
-\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| # | Issue | Jira ID | Description |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 1 | Vic1385 and Vic1227 low performance. | VPP-664 | Low NDR performance. |\r
-| | | | |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 2 | Sporadic NDR discovery test failures on x520. | CSIT-750 | Suspected issue with HW combination of X710-X520 in LF |\r
-| | | | infrastructure. Issue can't be replicated outside LF. |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 3 | VPP in 2t2c setups - large variation | CSIT-568 | Suspected NIC firmware or DPDK driver issue affecting NDR |\r
-| | of discovered NDR throughput values across | | throughput. Applies to XL710 and X710 NICs, x520 NICs are fine. |\r
-| | multiple test runs with xl710 and x710 NICs. | | |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
-| 4 | Lower than expected NDR throughput with | CSIT-569 | Suspected NIC firmware or DPDK driver issue affecting NDR and |\r
-| | xl710 and x710 NICs, compared to x520 NICs. | | PDR throughput. Applies to XL710 and X710 NICs. |\r
-+---+-------------------------------------------------+------------+-----------------------------------------------------------------+\r
+Release Notes
+=============
+
+Changes in |csit-release|
+-------------------------
+
+#. VPP PERFORMANCE TESTS
+
+ - **Intel Xeon 2n-skx, 3n-skx and 2n-clx testbeds**: VPP performance
+ test data is not included in this report version. This is due to
+ the lower performance and behaviour inconsistency of these
+ systems following the upgrade of processor microcode packages
+ (skx ucode 0x2000064, clx ucode 0x500002c), done as part of
+ updating Ubuntu 18.04 LTS kernel version. Tested VPP and DPDK
+ applications (L3fwd) are affected. Skx and Clx test data will be
+ added in subsequent maintenance report version(s) once the issue
+ is resolved. See :ref:`vpp_known_issues`.
+
+ - **Service density 2n-skx tests**: Added new NF density tests with
+ IPsec encryption between DUTs.
+
+ - **AVF tests**: Full test coveraged based on code changes in CSIT
+ core layer (driver/interface awareness) and generated by suite
+ generator (Intel Fortville NICs only).
+
+ - **Hoststack TCP/IP tests**: Major refactor of VPP Hoststack TCP/IP
+ performance tests using WRK generator talking to the VPP HTTP
+ static server plugin measuring connections per second and
+ requests per second. Added iperf3 tests with LDPreload.
+
+ - **Latency HDRHistogram**: Added High Dynamic Range Histogram
+ latency measurements based on the new capability in TRex traffic
+ generator. HDRH latency data presented in latency packet
+ percentile graphs and in detailed results tables.
+
+ - **Mellanox MCX556A-EDAT tests**: Added tests with Mellanox
+ ConnectX5-2p100GE NICs in 2n-clx testbeds using VPP native rdma
+ driver.
+
+ - **IPsec reconfiguration tests**: Added tests measuring the impact
+ of IPsec tunnels creations and removals.
+
+ - **Load Balancer tests**: Added VPP performance tests for Maglev,
+ L3DSR (Direct Server Return), Layer 4 Load Balancing NAT Mode.
+
+..
+ // Alternative Note for 1st Bullet when bad microcode Skx, Clx results are published
+ - **Intel Xeon 2n-skx, 3n-skx and 2n-clx testbeds**: VPP performance
+ test data is included in this report version, but it shows lower
+ performance and behaviour inconsistency of these systems
+ following the upgrade of processor microcode packages (skx ucode
+ 0x2000064, clx ucode 0x500002c) as part of updating Ubuntu 18.04
+ LTS kernel version. Tested VPP and DPDK applications (L3fwd) are
+ affected. Skx and Clx test data will be corrected in subsequent
+ maintenance report version(s) once the issue is resolved. See
+ :ref:`vpp_known_issues`.
+
+#. TEST FRAMEWORK
+
+ - **CSIT Python3 support**: Full migration of CSIT from Python2.7 to
+ Python3.6. This change includes library migration, PIP dependency
+ upgrade, CSIT container images, infrastructure packages
+ ugrade/installation.
+
+ - **CSIT PAPI support**: Finished conversion of CSIT VAT L1 keywords
+ to PAPI L1 KWs in CSIT using VPP Python bindings (VPP PAPI).
+ Redesign of key components of PAPI Socket Executor and PAPI
+ history. Due to issues with PAPI performance, VAT is still used
+ in CSIT for all VPP scale tests. See known issues below.
+
+ - **Test Suite Generator**: Added capability to generate suites for
+ different drivers per NIC model including DPDK, AVF, RDMA.
+ Extended coverage for all tests.
+
+ - **General Code Housekeeping**: Ongoing RF keywords optimizations,
+ removal of redundant RF keywords and aligning of suite/test
+ setup/teardowns.
+
+
+#. PRESENTATION AND ANALYTICS LAYER
+
+ - **Graphs layout improvements**: Improved performance graphs layout
+ for better readibility and maintenance: test grouping, axis
+ labels, descriptions, other informative decoration.
+
+ - **Latency graphs**: Min/Avg/Max group bar latency graphs are
+ replaced with packet latency percentile distributon at different
+ background packet loads based on TRex latency hdrhistogram
+ measurements.
+
+.. raw:: latex
+
+ \clearpage
+
+.. _vpp_known_issues:
+
+Known Issues
+------------
+
+List of known issues in |csit-release| for VPP performance tests:
+
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| # | JiraID | Issue Description |
++====+=========================================+===========================================================================================================+
+| 1 | `CSIT-570 | Sporadic (1 in 200) NDR discovery test failures on x520. DPDK reporting rx-errors, indicating L1 issue. |
+| | <https://jira.fd.io/browse/CSIT-570>`_ | Suspected issue with HW combination of X710-X520 in LF testbeds. Not observed outside of LF testbeds. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 2 | `VPP-662 | 9000B packets not supported by NICs VIC1227 and VIC1387. |
+| | <https://jira.fd.io/browse/VPP-662>`_ | |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 3 | `CSIT-1498 | Memif tests are sporadically failing on initialization of memif connection. |
+| | <https://jira.fd.io/browse/CSIT-1498>`_ | |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 4 | `VPP-1677 | 9000B ip4 nat44: VPP crash + coredump. |
+| | <https://jira.fd.io/browse/VPP-1677>`_ | VPP crashes very often in case that NAT44 is configured and it has to process IP4 jumbo frames (9000B). |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 5 | `CSIT-1591 | All CSIT scale tests can not use PAPI due to much slower performance compared to VAT/CLI (it takes much |
+| | <https://jira.fd.io/browse/CSIT-1499>`_ | longer to program VPP). This needs to be addressed on the PAPI side. |
+| +-----------------------------------------+ |
+| | `VPP-1763 | |
+| | <https://jira.fd.io/browse/VPP-1763>`_ | |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 6 | `VPP-1675 | IPv4 IPSEC 9000B packet tests are failing as no packet is forwarded. |
+| | <https://jira.fd.io/browse/VPP-1675>`_ | Reason: chained buffers are not supported. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 7 | `CSIT-1593 | IPv4 AVF 9000B packet tests are failing on 3n-skx while passing on 2n-skx. |
+| | <https://jira.fd.io/browse/CSIT-1593>`_ | |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+| 8 | `CSIT-1675 | Intel Xeon 2n-skx, 3n-skx and 2n-clx testbeds behaviour and performance became inconsistent following |
+| | <https://jira.fd.io/browse/CSIT-1675>`_ | the upgrade to the latest Ubuntu 18.04 LTS kernel version (4.15.0-72-generic) and associated microcode |
+| | | packages (skx ucode 0x2000064, clx ucode 0x500002c). VPP as well as DPDK L3fwd tests are affected. |
++----+-----------------------------------------+-----------------------------------------------------------------------------------------------------------+
+