mac->ops.led_off = ixgbe_led_off_generic;
mac->ops.blink_led_start = ixgbe_blink_led_start_generic;
mac->ops.blink_led_stop = ixgbe_blink_led_stop_generic;
+ mac->ops.init_led_link_act = ixgbe_init_led_link_act_generic;
/* RAR, Multicast, VLAN */
mac->ops.set_rar = ixgbe_set_rar_generic;
break;
case ixgbe_media_type_backplane:
- supported = true;
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI)
+ supported = false;
+ else
+ supported = true;
break;
case ixgbe_media_type_copper:
/* only some copper devices support flow control autoneg */
/* Setup flow control */
ret_val = ixgbe_setup_fc(hw);
- if (ret_val != IXGBE_SUCCESS && ret_val != IXGBE_NOT_IMPLEMENTED)
+ if (ret_val != IXGBE_SUCCESS && ret_val != IXGBE_NOT_IMPLEMENTED) {
+ DEBUGOUT1("Flow control setup failed, returning %d\n", ret_val);
return ret_val;
+ }
/* Cache bit indicating need for crosstalk fix */
switch (hw->mac.type) {
/* Reset the hardware */
status = hw->mac.ops.reset_hw(hw);
- if (status == IXGBE_SUCCESS) {
+ if (status == IXGBE_SUCCESS || status == IXGBE_ERR_SFP_NOT_PRESENT) {
/* Start the HW */
status = hw->mac.ops.start_hw(hw);
}
+ /* Initialize the LED link active for LED blink support */
+ if (hw->mac.ops.init_led_link_act)
+ hw->mac.ops.init_led_link_act(hw);
+
+ if (status != IXGBE_SUCCESS)
+ DEBUGOUT1("Failed to initialize HW, STATUS = %d\n", status);
+
return status;
}
return ixgbe_disable_pcie_master(hw);
}
+/**
+ * ixgbe_init_led_link_act_generic - Store the LED index link/activity.
+ * @hw: pointer to hardware structure
+ *
+ * Store the index for the link active LED. This will be used to support
+ * blinking the LED.
+ **/
+s32 ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ u32 led_reg, led_mode;
+ u8 i;
+
+ led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
+
+ /* Get LED link active from the LEDCTL register */
+ for (i = 0; i < 4; i++) {
+ led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i);
+
+ if ((led_mode & IXGBE_LED_MODE_MASK_BASE) ==
+ IXGBE_LED_LINK_ACTIVE) {
+ mac->led_link_act = i;
+ return IXGBE_SUCCESS;
+ }
+ }
+
+ /*
+ * If LEDCTL register does not have the LED link active set, then use
+ * known MAC defaults.
+ */
+ switch (hw->mac.type) {
+ case ixgbe_mac_X550EM_a:
+ case ixgbe_mac_X550EM_x:
+ mac->led_link_act = 1;
+ break;
+ default:
+ mac->led_link_act = 2;
+ }
+ return IXGBE_SUCCESS;
+}
+
/**
* ixgbe_led_on_generic - Turns on the software controllable LEDs.
* @hw: pointer to hardware structure
}
/* was that the last pool using this rar? */
- if (mpsar_lo == 0 && mpsar_hi == 0 && rar != 0)
+ if (mpsar_lo == 0 && mpsar_hi == 0 &&
+ rar != 0 && rar != hw->mac.san_mac_rar_index)
hw->mac.ops.clear_rar(hw, rar);
done:
return IXGBE_SUCCESS;
break;
case IXGBE_LINKS_SPEED_100_82599:
*speed = IXGBE_LINK_SPEED_100_FULL;
- if (hw->mac.type >= ixgbe_mac_X550) {
+ if (hw->mac.type == ixgbe_mac_X550) {
if (links_reg & IXGBE_LINKS_SPEED_NON_STD)
*speed = IXGBE_LINK_SPEED_5GB_FULL;
}
/* first pull in the header so we know the buffer length */
for (bi = 0; bi < dword_len; bi++) {
buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
- IXGBE_LE32_TO_CPUS(&buffer[bi]);
+ IXGBE_LE32_TO_CPUS((uintptr_t)&buffer[bi]);
}
/* If there is any thing in data position pull it in */
/* Pull in the rest of the buffer (bi is where we left off) */
for (; bi <= dword_len; bi++) {
buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
- IXGBE_LE32_TO_CPUS(&buffer[bi]);
+ IXGBE_LE32_TO_CPUS((uintptr_t)&buffer[bi]);
}
rel_out:
* semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
**/
s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
- u8 build, u8 sub)
+ u8 build, u8 sub, u16 len,
+ const char *driver_ver)
{
struct ixgbe_hic_drv_info fw_cmd;
int i;
s32 ret_val = IXGBE_SUCCESS;
DEBUGFUNC("ixgbe_set_fw_drv_ver_generic");
+ UNREFERENCED_2PARAMETER(len, driver_ver);
fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN;
ixgbe_flap_tx_laser(hw);
/* Wait for the controller to acquire link. Per IEEE 802.3ap,
- * Section 73.10.2, we may have to wait up to 500ms if KR is
+ * Section 73.10.2, we may have to wait up to 1000ms if KR is
* attempted. 82599 uses the same timing for 10g SFI.
*/
- for (i = 0; i < 5; i++) {
+ for (i = 0; i < 10; i++) {
/* Wait for the link partner to also set speed */
msec_delay(100);