-/*******************************************************************************
-
-Copyright (c) 2001-2015, Intel Corporation
-All rights reserved.
-
-Redistribution and use in source and binary forms, with or without
-modification, are permitted provided that the following conditions are met:
-
- 1. Redistributions of source code must retain the above copyright notice,
- this list of conditions and the following disclaimer.
-
- 2. Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in the
- documentation and/or other materials provided with the distribution.
-
- 3. Neither the name of the Intel Corporation nor the names of its
- contributors may be used to endorse or promote products derived from
- this software without specific prior written permission.
-
-THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
-LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
-CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
-SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
-INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
-CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
-ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
-POSSIBILITY OF SUCH DAMAGE.
-
-***************************************************************************/
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright(c) 2001-2018
+ */
#include "ixgbe_common.h"
#include "ixgbe_phy.h"
mac->ops.led_off = ixgbe_led_off_generic;
mac->ops.blink_led_start = ixgbe_blink_led_start_generic;
mac->ops.blink_led_stop = ixgbe_blink_led_stop_generic;
+ mac->ops.init_led_link_act = ixgbe_init_led_link_act_generic;
/* RAR, Multicast, VLAN */
mac->ops.set_rar = ixgbe_set_rar_generic;
switch (hw->phy.media_type) {
case ixgbe_media_type_fiber_qsfp:
case ixgbe_media_type_fiber:
- hw->mac.ops.check_link(hw, &speed, &link_up, false);
- /* if link is down, assume supported */
- if (link_up)
- supported = speed == IXGBE_LINK_SPEED_1GB_FULL ?
+ /* flow control autoneg black list */
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_A_SFP:
+ case IXGBE_DEV_ID_X550EM_A_SFP_N:
+ case IXGBE_DEV_ID_X550EM_A_QSFP:
+ case IXGBE_DEV_ID_X550EM_A_QSFP_N:
+ supported = false;
+ break;
+ default:
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+ /* if link is down, assume supported */
+ if (link_up)
+ supported = speed == IXGBE_LINK_SPEED_1GB_FULL ?
true : false;
- else
- supported = true;
+ else
+ supported = true;
+ }
+
break;
case ixgbe_media_type_backplane:
- supported = true;
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI)
+ supported = false;
+ else
+ supported = true;
break;
case ixgbe_media_type_copper:
/* only some copper devices support flow control autoneg */
case IXGBE_DEV_ID_X550T:
case IXGBE_DEV_ID_X550T1:
case IXGBE_DEV_ID_X550EM_X_10G_T:
+ case IXGBE_DEV_ID_X550EM_A_10G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
supported = true;
break;
default:
break;
}
- ERROR_REPORT2(IXGBE_ERROR_UNSUPPORTED,
- "Device %x does not support flow control autoneg",
- hw->device_id);
+ if (!supported)
+ ERROR_REPORT2(IXGBE_ERROR_UNSUPPORTED,
+ "Device %x does not support flow control autoneg",
+ hw->device_id);
return supported;
}
if (ret_val != IXGBE_SUCCESS)
goto out;
- /* only backplane uses autoc so fall though */
+ /* fall through - only backplane uses autoc */
case ixgbe_media_type_fiber_qsfp:
case ixgbe_media_type_fiber:
reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
{
s32 ret_val;
u32 ctrl_ext;
+ u16 device_caps;
DEBUGFUNC("ixgbe_start_hw_generic");
/* Setup flow control */
ret_val = ixgbe_setup_fc(hw);
- if (ret_val != IXGBE_SUCCESS)
- goto out;
+ if (ret_val != IXGBE_SUCCESS && ret_val != IXGBE_NOT_IMPLEMENTED) {
+ DEBUGOUT1("Flow control setup failed, returning %d\n", ret_val);
+ return ret_val;
+ }
+
+ /* Cache bit indicating need for crosstalk fix */
+ switch (hw->mac.type) {
+ case ixgbe_mac_82599EB:
+ case ixgbe_mac_X550EM_x:
+ case ixgbe_mac_X550EM_a:
+ hw->mac.ops.get_device_caps(hw, &device_caps);
+ if (device_caps & IXGBE_DEVICE_CAPS_NO_CROSSTALK_WR)
+ hw->need_crosstalk_fix = false;
+ else
+ hw->need_crosstalk_fix = true;
+ break;
+ default:
+ hw->need_crosstalk_fix = false;
+ break;
+ }
/* Clear adapter stopped flag */
hw->adapter_stopped = false;
-out:
- return ret_val;
+ return IXGBE_SUCCESS;
}
/**
/* Reset the hardware */
status = hw->mac.ops.reset_hw(hw);
- if (status == IXGBE_SUCCESS) {
+ if (status == IXGBE_SUCCESS || status == IXGBE_ERR_SFP_NOT_PRESENT) {
/* Start the HW */
status = hw->mac.ops.start_hw(hw);
}
+ /* Initialize the LED link active for LED blink support */
+ if (hw->mac.ops.init_led_link_act)
+ hw->mac.ops.init_led_link_act(hw);
+
+ if (status != IXGBE_SUCCESS)
+ DEBUGOUT1("Failed to initialize HW, STATUS = %d\n", status);
+
return status;
}
if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP) {
hw->eeprom.ops.read(hw, IXGBE_EEPROM_CTRL_4, &ee_ctrl_4);
bus->instance_id = (ee_ctrl_4 & IXGBE_EE_CTRL_4_INST_ID) >>
- IXGBE_EE_CTRL_4_INST_ID_SHIFT;
+ IXGBE_EE_CTRL_4_INST_ID_SHIFT;
}
}
return ixgbe_disable_pcie_master(hw);
}
+/**
+ * ixgbe_init_led_link_act_generic - Store the LED index link/activity.
+ * @hw: pointer to hardware structure
+ *
+ * Store the index for the link active LED. This will be used to support
+ * blinking the LED.
+ **/
+s32 ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ u32 led_reg, led_mode;
+ u8 i;
+
+ led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
+
+ /* Get LED link active from the LEDCTL register */
+ for (i = 0; i < 4; i++) {
+ led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i);
+
+ if ((led_mode & IXGBE_LED_MODE_MASK_BASE) ==
+ IXGBE_LED_LINK_ACTIVE) {
+ mac->led_link_act = i;
+ return IXGBE_SUCCESS;
+ }
+ }
+
+ /*
+ * If LEDCTL register does not have the LED link active set, then use
+ * known MAC defaults.
+ */
+ switch (hw->mac.type) {
+ case ixgbe_mac_X550EM_a:
+ case ixgbe_mac_X550EM_x:
+ mac->led_link_act = 1;
+ break;
+ default:
+ mac->led_link_act = 2;
+ }
+ return IXGBE_SUCCESS;
+}
+
/**
* ixgbe_led_on_generic - Turns on the software controllable LEDs.
* @hw: pointer to hardware structure
DEBUGFUNC("ixgbe_led_on_generic");
+ if (index > 3)
+ return IXGBE_ERR_PARAM;
+
/* To turn on the LED, set mode to ON. */
led_reg &= ~IXGBE_LED_MODE_MASK(index);
led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index);
DEBUGFUNC("ixgbe_led_off_generic");
+ if (index > 3)
+ return IXGBE_ERR_PARAM;
+
/* To turn off the LED, set mode to OFF. */
led_reg &= ~IXGBE_LED_MODE_MASK(index);
led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index);
/**
* ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM
* @hw: pointer to hardware structure
+ * @count: number of bits to shift
**/
STATIC u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
{
/**
* ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input.
* @hw: pointer to hardware structure
- * @eecd: EECD's current value
+ * @eec: EEC's current value
**/
STATIC void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
{
* ixgbe_add_uc_addr - Adds a secondary unicast address.
* @hw: pointer to hardware structure
* @addr: new address
+ * @vmdq: VMDq "set" or "pool" index
*
* Adds it to unused receive address register or goes into promiscuous mode.
**/
/**
* ixgbe_set_mta - Set bit-vector in multicast table
* @hw: pointer to hardware structure
- * @hash_value: Multicast address hash value
+ * @mc_addr: Multicast address
*
* Sets the bit-vector in the multicast table.
**/
* advertised settings
**/
s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
- u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
+ u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
{
if ((!(adv_reg)) || (!(lp_reg))) {
ERROR_REPORT3(IXGBE_ERROR_UNSUPPORTED,
**/
s32 ixgbe_disable_sec_rx_path_generic(struct ixgbe_hw *hw)
{
-#define IXGBE_MAX_SECRX_POLL 40
+#define IXGBE_MAX_SECRX_POLL 4000
int i;
int secrxreg;
break;
else
/* Use interrupt-safe sleep just in case */
- usec_delay(1000);
+ usec_delay(10);
}
/* For informational purposes only */
/**
* prot_autoc_read_generic - Hides MAC differences needed for AUTOC read
* @hw: pointer to hardware structure
+ * @locked: bool to indicate whether the SW/FW lock was taken
* @reg_val: Value we read from AUTOC
*
* The default case requires no protection so just to the register read.
**/
s32 ixgbe_enable_sec_rx_path_generic(struct ixgbe_hw *hw)
{
- int secrxreg;
+ u32 secrxreg;
DEBUGFUNC("ixgbe_enable_sec_rx_path_generic");
DEBUGFUNC("ixgbe_blink_led_start_generic");
+ if (index > 3)
+ return IXGBE_ERR_PARAM;
+
/*
* Link must be up to auto-blink the LEDs;
* Force it if link is down.
DEBUGFUNC("ixgbe_blink_led_stop_generic");
+ if (index > 3)
+ return IXGBE_ERR_PARAM;
+
+
ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
if (ret_val != IXGBE_SUCCESS)
goto out;
}
/* was that the last pool using this rar? */
- if (mpsar_lo == 0 && mpsar_hi == 0 && rar != 0)
+ if (mpsar_lo == 0 && mpsar_hi == 0 &&
+ rar != 0 && rar != hw->mac.san_mac_rar_index)
hw->mac.ops.clear_rar(hw, rar);
done:
return IXGBE_SUCCESS;
* ixgbe_find_vlvf_slot - find the vlanid or the first empty slot
* @hw: pointer to hardware structure
* @vlan: VLAN id to write to VLAN filter
+ * @vlvf_bypass: true to find vlanid only, false returns first empty slot if
+ * vlanid not found
+ *
*
* return the VLVF index where this VLAN id should be placed
*
vfta_delta = 1 << (vlan % 32);
vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regidx));
- /* vfta_delta represents the difference between the current value
+ /*
+ * vfta_delta represents the difference between the current value
* of vfta and the value we want in the register. Since the diff
* is an XOR mask we can just update the vfta using an XOR
*/
* @vind: VMDq output index that maps queue to VLAN id in VLVFB
* @vlan_on: boolean flag to turn on/off VLAN in VLVF
* @vfta_delta: pointer to the difference between the current value of VFTA
- * and the desired value
+ * and the desired value
* @vfta: the desired value of the VFTA
* @vlvf_bypass: boolean flag indicating updating default pool is okay
*
*/
if (!(IXGBE_READ_REG(hw, IXGBE_VT_CTL) & IXGBE_VT_CTL_VT_ENABLE))
return IXGBE_SUCCESS;
+
vlvf_index = ixgbe_find_vlvf_slot(hw, vlan, vlvf_bypass);
if (vlvf_index < 0)
return vlvf_index;
* we run the risk of stray packets leaking into
* the PF via the default pool
*/
- if (vfta_delta)
+ if (*vfta_delta)
IXGBE_WRITE_REG(hw, IXGBE_VFTA(vlan / 32), vfta);
/* disable VLVF and clear remaining bit from pool */
return IXGBE_SUCCESS;
}
+
/* If there are still bits set in the VLVFB registers
* for the VLAN ID indicated we need to see if the
* caller is requesting that we clear the VFTA entry bit.
return IXGBE_SUCCESS;
}
+/**
+ * ixgbe_need_crosstalk_fix - Determine if we need to do cross talk fix
+ * @hw: pointer to hardware structure
+ *
+ * Contains the logic to identify if we need to verify link for the
+ * crosstalk fix
+ **/
+static bool ixgbe_need_crosstalk_fix(struct ixgbe_hw *hw)
+{
+
+ /* Does FW say we need the fix */
+ if (!hw->need_crosstalk_fix)
+ return false;
+
+ /* Only consider SFP+ PHYs i.e. media type fiber */
+ switch (hw->mac.ops.get_media_type(hw)) {
+ case ixgbe_media_type_fiber:
+ case ixgbe_media_type_fiber_qsfp:
+ break;
+ default:
+ return false;
+ }
+
+ return true;
+}
+
/**
* ixgbe_check_mac_link_generic - Determine link and speed status
* @hw: pointer to hardware structure
DEBUGFUNC("ixgbe_check_mac_link_generic");
+ /* If Crosstalk fix enabled do the sanity check of making sure
+ * the SFP+ cage is full.
+ */
+ if (ixgbe_need_crosstalk_fix(hw)) {
+ u32 sfp_cage_full;
+
+ switch (hw->mac.type) {
+ case ixgbe_mac_82599EB:
+ sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
+ IXGBE_ESDP_SDP2;
+ break;
+ case ixgbe_mac_X550EM_x:
+ case ixgbe_mac_X550EM_a:
+ sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
+ IXGBE_ESDP_SDP0;
+ break;
+ default:
+ /* sanity check - No SFP+ devices here */
+ sfp_cage_full = false;
+ break;
+ }
+
+ if (!sfp_cage_full) {
+ *link_up = false;
+ *speed = IXGBE_LINK_SPEED_UNKNOWN;
+ return IXGBE_SUCCESS;
+ }
+ }
+
/* clear the old state */
links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS);
break;
case IXGBE_LINKS_SPEED_100_82599:
*speed = IXGBE_LINK_SPEED_100_FULL;
- if (hw->mac.type >= ixgbe_mac_X550) {
+ if (hw->mac.type == ixgbe_mac_X550) {
if (links_reg & IXGBE_LINKS_SPEED_NON_STD)
*speed = IXGBE_LINK_SPEED_5GB_FULL;
}
break;
+ case IXGBE_LINKS_SPEED_10_X550EM_A:
+ *speed = IXGBE_LINK_SPEED_UNKNOWN;
+#ifdef PREBOOT_SUPPORT
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII_L)
+ *speed = IXGBE_LINK_SPEED_10_FULL;
+#else
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L)
+ *speed = IXGBE_LINK_SPEED_10_FULL;
+#endif /* PREBOOT_SUPPORT */
+ break;
default:
*speed = IXGBE_LINK_SPEED_UNKNOWN;
}
}
/**
- * ixgbe_host_interface_command - Issue command to manageability block
+ * ixgbe_hic_unlocked - Issue command to manageability block unlocked
* @hw: pointer to the HW structure
- * @buffer: contains the command to write and where the return status will
- * be placed
+ * @buffer: command to write and where the return status will be placed
* @length: length of buffer, must be multiple of 4 bytes
* @timeout: time in ms to wait for command completion
- * @return_data: read and return data from the buffer (true) or not (false)
- * Needed because FW structures are big endian and decoding of
- * these fields can be 8 bit or 16 bit based on command. Decoding
- * is not easily understood without making a table of commands.
- * So we will leave this up to the caller to read back the data
- * in these cases.
*
* Communicates with the manageability block. On success return IXGBE_SUCCESS
* else returns semaphore error when encountering an error acquiring
* semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ *
+ * This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
+ * by the caller.
**/
-s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, u32 *buffer,
- u32 length, u32 timeout, bool return_data)
+s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length,
+ u32 timeout)
{
- u32 hicr, i, bi, fwsts;
- u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
- u16 buf_len;
+ u32 hicr, i, fwsts;
u16 dword_len;
- s32 status;
- DEBUGFUNC("ixgbe_host_interface_command");
+ DEBUGFUNC("ixgbe_hic_unlocked");
- if (length == 0 || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
+ if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
DEBUGOUT1("Buffer length failure buffersize=%d.\n", length);
return IXGBE_ERR_HOST_INTERFACE_COMMAND;
}
- /* Take management host interface semaphore */
- status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
-
- if (status)
- return status;
/* Set bit 9 of FWSTS clearing FW reset indication */
fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS);
/* Check that the host interface is enabled. */
hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
- if ((hicr & IXGBE_HICR_EN) == 0) {
+ if (!(hicr & IXGBE_HICR_EN)) {
DEBUGOUT("IXGBE_HOST_EN bit disabled.\n");
- status = IXGBE_ERR_HOST_INTERFACE_COMMAND;
- goto rel_out;
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
}
/* Calculate length in DWORDs. We must be DWORD aligned */
- if ((length % (sizeof(u32))) != 0) {
+ if (length % sizeof(u32)) {
DEBUGOUT("Buffer length failure, not aligned to dword");
- status = IXGBE_ERR_INVALID_ARGUMENT;
- goto rel_out;
+ return IXGBE_ERR_INVALID_ARGUMENT;
}
dword_len = length >> 2;
}
/* Check command completion */
- if ((timeout != 0 && i == timeout) ||
+ if ((timeout && i == timeout) ||
!(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) {
ERROR_REPORT1(IXGBE_ERROR_CAUTION,
"Command has failed with no status valid.\n");
- status = IXGBE_ERR_HOST_INTERFACE_COMMAND;
- goto rel_out;
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
}
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_host_interface_command - Issue command to manageability block
+ * @hw: pointer to the HW structure
+ * @buffer: contains the command to write and where the return status will
+ * be placed
+ * @length: length of buffer, must be multiple of 4 bytes
+ * @timeout: time in ms to wait for command completion
+ * @return_data: read and return data from the buffer (true) or not (false)
+ * Needed because FW structures are big endian and decoding of
+ * these fields can be 8 bit or 16 bit based on command. Decoding
+ * is not easily understood without making a table of commands.
+ * So we will leave this up to the caller to read back the data
+ * in these cases.
+ *
+ * Communicates with the manageability block. On success return IXGBE_SUCCESS
+ * else returns semaphore error when encountering an error acquiring
+ * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ **/
+s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, u32 *buffer,
+ u32 length, u32 timeout, bool return_data)
+{
+ u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
+ struct ixgbe_hic_hdr *resp = (struct ixgbe_hic_hdr *)buffer;
+ u16 buf_len;
+ s32 status;
+ u32 bi;
+ u32 dword_len;
+
+ DEBUGFUNC("ixgbe_host_interface_command");
+
+ if (length == 0 || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
+ DEBUGOUT1("Buffer length failure buffersize=%d.\n", length);
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+ }
+
+ /* Take management host interface semaphore */
+ status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
+ if (status)
+ return status;
+
+ status = ixgbe_hic_unlocked(hw, buffer, length, timeout);
+ if (status)
+ goto rel_out;
+
if (!return_data)
goto rel_out;
/* first pull in the header so we know the buffer length */
for (bi = 0; bi < dword_len; bi++) {
buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
- IXGBE_LE32_TO_CPUS(&buffer[bi]);
+ IXGBE_LE32_TO_CPUS((uintptr_t)&buffer[bi]);
}
- /* If there is any thing in data position pull it in */
- buf_len = ((struct ixgbe_hic_hdr *)buffer)->buf_len;
- if (buf_len == 0)
+ /*
+ * If there is any thing in data position pull it in
+ * Read Flash command requires reading buffer length from
+ * two byes instead of one byte
+ */
+ if (resp->cmd == 0x30) {
+ for (; bi < dword_len + 2; bi++) {
+ buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
+ bi);
+ IXGBE_LE32_TO_CPUS(&buffer[bi]);
+ }
+ buf_len = (((u16)(resp->cmd_or_resp.ret_status) << 3)
+ & 0xF00) | resp->buf_len;
+ hdr_size += (2 << 2);
+ } else {
+ buf_len = resp->buf_len;
+ }
+ if (!buf_len)
goto rel_out;
if (length < buf_len + hdr_size) {
/* Pull in the rest of the buffer (bi is where we left off) */
for (; bi <= dword_len; bi++) {
buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
- IXGBE_LE32_TO_CPUS(&buffer[bi]);
+ IXGBE_LE32_TO_CPUS((uintptr_t)&buffer[bi]);
}
rel_out:
* @min: driver version minor number
* @build: driver version build number
* @sub: driver version sub build number
+ * @len: unused
+ * @driver_ver: unused
*
* Sends driver version number to firmware through the manageability
* block. On success return IXGBE_SUCCESS
* semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
**/
s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
- u8 build, u8 sub)
+ u8 build, u8 sub, u16 len,
+ const char *driver_ver)
{
struct ixgbe_hic_drv_info fw_cmd;
int i;
s32 ret_val = IXGBE_SUCCESS;
DEBUGFUNC("ixgbe_set_fw_drv_ver_generic");
+ UNREFERENCED_2PARAMETER(len, driver_ver);
fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN;
fw_cmd.ver_build = build;
fw_cmd.ver_sub = sub;
fw_cmd.hdr.checksum = 0;
- fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
- (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
fw_cmd.pad = 0;
fw_cmd.pad2 = 0;
+ fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
+ (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
ret_val = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd,
rxpktsize <<= IXGBE_RXPBSIZE_SHIFT;
for (; i < (num_pb / 2); i++)
IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
- /* Fall through to configure remaining packet buffers */
+ /* fall through - configure remaining packet buffers */
case PBA_STRATEGY_EQUAL:
rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT;
for (; i < num_pb; i++)
/**
* ixgbe_get_thermal_sensor_data - Gathers thermal sensor data
* @hw: pointer to hardware structure
- * @data: pointer to the thermal sensor data structure
*
* Returns the thermal sensor data structure
**/
return IXGBE_NOT_IMPLEMENTED;
}
+/**
+ * ixgbe_get_orom_version - Return option ROM from EEPROM
+ *
+ * @hw: pointer to hardware structure
+ * @nvm_ver: pointer to output structure
+ *
+ * if valid option ROM version, nvm_ver->or_valid set to true
+ * else nvm_ver->or_valid is false.
+ **/
+void ixgbe_get_orom_version(struct ixgbe_hw *hw,
+ struct ixgbe_nvm_version *nvm_ver)
+{
+ u16 offset, eeprom_cfg_blkh, eeprom_cfg_blkl;
+
+ nvm_ver->or_valid = false;
+ /* Option Rom may or may not be present. Start with pointer */
+ hw->eeprom.ops.read(hw, NVM_OROM_OFFSET, &offset);
+
+ /* make sure offset is valid */
+ if ((offset == 0x0) || (offset == NVM_INVALID_PTR))
+ return;
+
+ hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_HI, &eeprom_cfg_blkh);
+ hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_LOW, &eeprom_cfg_blkl);
+
+ /* option rom exists and is valid */
+ if ((eeprom_cfg_blkl | eeprom_cfg_blkh) == 0x0 ||
+ eeprom_cfg_blkl == NVM_VER_INVALID ||
+ eeprom_cfg_blkh == NVM_VER_INVALID)
+ return;
+
+ nvm_ver->or_valid = true;
+ nvm_ver->or_major = eeprom_cfg_blkl >> NVM_OROM_SHIFT;
+ nvm_ver->or_build = (eeprom_cfg_blkl << NVM_OROM_SHIFT) |
+ (eeprom_cfg_blkh >> NVM_OROM_SHIFT);
+ nvm_ver->or_patch = eeprom_cfg_blkh & NVM_OROM_PATCH_MASK;
+}
+
+/**
+ * ixgbe_get_oem_prod_version - Return OEM Product version
+ *
+ * @hw: pointer to hardware structure
+ * @nvm_ver: pointer to output structure
+ *
+ * if valid OEM product version, nvm_ver->oem_valid set to true
+ * else nvm_ver->oem_valid is false.
+ **/
+void ixgbe_get_oem_prod_version(struct ixgbe_hw *hw,
+ struct ixgbe_nvm_version *nvm_ver)
+{
+ u16 rel_num, prod_ver, mod_len, cap, offset;
+
+ nvm_ver->oem_valid = false;
+ hw->eeprom.ops.read(hw, NVM_OEM_PROD_VER_PTR, &offset);
+
+ /* Return is offset to OEM Product Version block is invalid */
+ if (offset == 0x0 && offset == NVM_INVALID_PTR)
+ return;
+
+ /* Read product version block */
+ hw->eeprom.ops.read(hw, offset, &mod_len);
+ hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_CAP_OFF, &cap);
+
+ /* Return if OEM product version block is invalid */
+ if (mod_len != NVM_OEM_PROD_VER_MOD_LEN ||
+ (cap & NVM_OEM_PROD_VER_CAP_MASK) != 0x0)
+ return;
+
+ hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_L, &prod_ver);
+ hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_H, &rel_num);
+
+ /* Return if version is invalid */
+ if ((rel_num | prod_ver) == 0x0 ||
+ rel_num == NVM_VER_INVALID || prod_ver == NVM_VER_INVALID)
+ return;
+
+ nvm_ver->oem_major = prod_ver >> NVM_VER_SHIFT;
+ nvm_ver->oem_minor = prod_ver & NVM_VER_MASK;
+ nvm_ver->oem_release = rel_num;
+ nvm_ver->oem_valid = true;
+}
+
+/**
+ * ixgbe_get_etk_id - Return Etrack ID from EEPROM
+ *
+ * @hw: pointer to hardware structure
+ * @nvm_ver: pointer to output structure
+ *
+ * word read errors will return 0xFFFF
+ **/
+void ixgbe_get_etk_id(struct ixgbe_hw *hw, struct ixgbe_nvm_version *nvm_ver)
+{
+ u16 etk_id_l, etk_id_h;
+
+ if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_LOW, &etk_id_l))
+ etk_id_l = NVM_VER_INVALID;
+ if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_HI, &etk_id_h))
+ etk_id_h = NVM_VER_INVALID;
+
+ /* The word order for the version format is determined by high order
+ * word bit 15.
+ */
+ if ((etk_id_h & NVM_ETK_VALID) == 0) {
+ nvm_ver->etk_id = etk_id_h;
+ nvm_ver->etk_id |= (etk_id_l << NVM_ETK_SHIFT);
+ } else {
+ nvm_ver->etk_id = etk_id_l;
+ nvm_ver->etk_id |= (etk_id_h << NVM_ETK_SHIFT);
+ }
+}
+
/**
* ixgbe_dcb_get_rtrup2tc_generic - read rtrup2tc reg
return false;
fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM_BY_MAC(hw));
- fwsm &= IXGBE_FWSM_MODE_MASK;
- return fwsm == IXGBE_FWSM_FW_MODE_PT;
+
+ return !!(fwsm & IXGBE_FWSM_FW_MODE_PT);
}
/**
speedcnt++;
highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
- /* If we already have link at this speed, just jump out */
- status = ixgbe_check_link(hw, &link_speed, &link_up, false);
- if (status != IXGBE_SUCCESS)
- return status;
-
- if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
- goto out;
-
/* Set the module link speed */
switch (hw->phy.media_type) {
case ixgbe_media_type_fiber:
ixgbe_flap_tx_laser(hw);
/* Wait for the controller to acquire link. Per IEEE 802.3ap,
- * Section 73.10.2, we may have to wait up to 500ms if KR is
+ * Section 73.10.2, we may have to wait up to 1000ms if KR is
* attempted. 82599 uses the same timing for 10g SFI.
*/
- for (i = 0; i < 5; i++) {
+ for (i = 0; i < 10; i++) {
/* Wait for the link partner to also set speed */
msec_delay(100);
if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
- /* If we already have link at this speed, just jump out */
- status = ixgbe_check_link(hw, &link_speed, &link_up, false);
- if (status != IXGBE_SUCCESS)
- return status;
-
- if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
- goto out;
-
/* Set the module link speed */
switch (hw->phy.media_type) {
case ixgbe_media_type_fiber:
Code Review / deb_dpdk.git / blobdiff