#include "ecore_status.h"
#include "ecore_sp_api.h"
+#include "ecore_int_api.h"
#ifndef __EXTRACT__LINUX__
enum ecore_rss_caps {
#endif
struct ecore_queue_start_common_params {
- /* Rx/Tx queue id */
- u8 queue_id;
+ /* Should always be relative to entity sending this. */
u8 vport_id;
+ u16 queue_id;
- /* stats_id is relative or absolute depends on function */
+ /* Relative, but relevant only for PFs */
u8 stats_id;
- u16 sb;
- u16 sb_idx;
- u16 vf_qid;
+
+ struct ecore_sb_info *p_sb;
+ u8 sb_idx;
+};
+
+struct ecore_rxq_start_ret_params {
+ void OSAL_IOMEM *p_prod;
+ void *p_handle;
+};
+
+struct ecore_txq_start_ret_params {
+ void OSAL_IOMEM *p_doorbell;
+ void *p_handle;
};
struct ecore_rss_params {
u8 update_rss_key;
u8 rss_caps;
u8 rss_table_size_log; /* The table size is 2 ^ rss_table_size_log */
- u16 rss_ind_table[ECORE_RSS_IND_TABLE_SIZE];
+
+ /* Indirection table consist of rx queue handles */
+ void *rss_ind_table[ECORE_RSS_IND_TABLE_SIZE];
u32 rss_key[ECORE_RSS_KEY_SIZE];
};
ECORE_FILTER_INNER_MAC_VNI_PAIR,
ECORE_FILTER_MAC_VNI_PAIR,
ECORE_FILTER_VNI,
+ ECORE_FILTER_UNUSED, /* @DPDK */
};
struct ecore_filter_ucast {
#define ECORE_ACCEPT_BCAST 0x20
};
+struct ecore_arfs_config_params {
+ bool tcp;
+ bool udp;
+ bool ipv4;
+ bool ipv6;
+ bool arfs_enable; /* Enable or disable arfs mode */
+};
+
/* Add / remove / move / remove-all unicast MAC-VLAN filters.
* FW will assert in the following cases, so driver should take care...:
* 1. Adding a filter to a full table.
struct ecore_spq_comp_cb *p_comp_data);
/**
- * @brief ecore_sp_eth_rx_queue_start - RX Queue Start Ramrod
+ * @brief ecore_eth_rx_queue_start - RX Queue Start Ramrod
*
* This ramrod initializes an RX Queue for a VPort. An Assert is generated if
* the VPort ID is not currently initialized.
*
* @param p_hwfn
* @param opaque_fid
- * @p_params [stats_id is relative, packed in p_params]
+ * @p_params Inputs; Relative for PF [SB being an exception]
* @param bd_max_bytes Maximum bytes that can be placed on a BD
* @param bd_chain_phys_addr Physical address of BDs for receive.
* @param cqe_pbl_addr Physical address of the CQE PBL Table.
* @param cqe_pbl_size Size of the CQE PBL Table
- * @param pp_prod Pointer to place producer's
- * address for the Rx Q (May be
- * NULL).
+ * @param p_ret_params Pointed struct to be filled with outputs.
*
* @return enum _ecore_status_t
*/
enum _ecore_status_t
-ecore_sp_eth_rx_queue_start(struct ecore_hwfn *p_hwfn,
- u16 opaque_fid,
- struct ecore_queue_start_common_params *p_params,
- u16 bd_max_bytes,
- dma_addr_t bd_chain_phys_addr,
- dma_addr_t cqe_pbl_addr,
- u16 cqe_pbl_size,
- void OSAL_IOMEM * *pp_prod);
+ecore_eth_rx_queue_start(struct ecore_hwfn *p_hwfn,
+ u16 opaque_fid,
+ struct ecore_queue_start_common_params *p_params,
+ u16 bd_max_bytes,
+ dma_addr_t bd_chain_phys_addr,
+ dma_addr_t cqe_pbl_addr,
+ u16 cqe_pbl_size,
+ struct ecore_rxq_start_ret_params *p_ret_params);
/**
- * @brief ecore_sp_eth_rx_queue_stop -
- *
- * This ramrod closes an RX queue. It sends RX queue stop ramrod
- * + CFC delete ramrod
+ * @brief ecore_eth_rx_queue_stop - This ramrod closes an Rx queue
*
* @param p_hwfn
- * @param rx_queue_id RX Queue ID
+ * @param p_rxq Handler of queue to close
* @param eq_completion_only If True completion will be on
* EQe, if False completion will be
* on EQe if p_hwfn opaque
* @return enum _ecore_status_t
*/
enum _ecore_status_t
-ecore_sp_eth_rx_queue_stop(struct ecore_hwfn *p_hwfn,
- u16 rx_queue_id,
- bool eq_completion_only,
- bool cqe_completion);
+ecore_eth_rx_queue_stop(struct ecore_hwfn *p_hwfn,
+ void *p_rxq,
+ bool eq_completion_only,
+ bool cqe_completion);
/**
- * @brief ecore_sp_eth_tx_queue_start - TX Queue Start Ramrod
+ * @brief - TX Queue Start Ramrod
*
* This ramrod initializes a TX Queue for a VPort. An Assert is generated if
* the VPort is not currently initialized.
* @param tc traffic class to use with this L2 txq
* @param pbl_addr address of the pbl array
* @param pbl_size number of entries in pbl
- * @param pp_doorbell Pointer to place doorbell pointer (May be NULL).
- * This address should be used with the
- * DIRECT_REG_WR macro.
+ * @param p_ret_params Pointer to fill the return parameters in.
*
* @return enum _ecore_status_t
*/
enum _ecore_status_t
-ecore_sp_eth_tx_queue_start(struct ecore_hwfn *p_hwfn,
- u16 opaque_fid,
- struct ecore_queue_start_common_params *p_params,
- u8 tc,
- dma_addr_t pbl_addr,
- u16 pbl_size,
- void OSAL_IOMEM * *pp_doorbell);
+ecore_eth_tx_queue_start(struct ecore_hwfn *p_hwfn,
+ u16 opaque_fid,
+ struct ecore_queue_start_common_params *p_params,
+ u8 tc,
+ dma_addr_t pbl_addr,
+ u16 pbl_size,
+ struct ecore_txq_start_ret_params *p_ret_params);
/**
- * @brief ecore_sp_eth_tx_queue_stop -
- *
- * This ramrod closes a TX queue. It sends TX queue stop ramrod
- * + CFC delete ramrod
+ * @brief ecore_eth_tx_queue_stop - closes a Tx queue
*
* @param p_hwfn
- * @param tx_queue_id TX Queue ID
+ * @param p_txq - handle to Tx queue needed to be closed
*
* @return enum _ecore_status_t
*/
-enum _ecore_status_t ecore_sp_eth_tx_queue_stop(struct ecore_hwfn *p_hwfn,
- u16 tx_queue_id);
+enum _ecore_status_t ecore_eth_tx_queue_stop(struct ecore_hwfn *p_hwfn,
+ void *p_txq);
enum ecore_tpa_mode {
ECORE_TPA_MODE_NONE,
bool zero_placement_offset;
bool check_mac;
bool check_ethtype;
+
+ /* Strict behavior on transmission errors */
+ bool b_err_illegal_vlan_mode;
+ bool b_err_illegal_inband_mode;
+ bool b_err_vlan_insert_with_inband;
+ bool b_err_small_pkt;
+ bool b_err_big_pkt;
+ bool b_err_anti_spoof;
+ bool b_err_ctrl_frame;
};
/**
u8 anti_spoofing_en;
u8 update_accept_any_vlan_flg;
u8 accept_any_vlan;
- unsigned long bins[8];
+ u32 bins[8];
struct ecore_rss_params *rss_params;
struct ecore_filter_accept_flags accept_flags;
struct ecore_sge_tpa_params *sge_tpa_params;
* @note Final phase API.
*
* @param p_hwfn
- * @param rx_queue_id RX Queue ID
- * @param num_rxqs Allow to update multiple rx
- * queues, from rx_queue_id to
- * (rx_queue_id + num_rxqs)
+ * @param pp_rxq_handlers An array of queue handlers to be updated.
+ * @param num_rxqs number of queues to update.
* @param complete_cqe_flg Post completion to the CQE Ring if set
* @param complete_event_flg Post completion to the Event Ring if set
+ * @param comp_mode
+ * @param p_comp_data
*
* @return enum _ecore_status_t
*/
enum _ecore_status_t
ecore_sp_eth_rx_queues_update(struct ecore_hwfn *p_hwfn,
- u16 rx_queue_id,
+ void **pp_rxq_handlers,
u8 num_rxqs,
u8 complete_cqe_flg,
u8 complete_event_flg,
void ecore_reset_vport_stats(struct ecore_dev *p_dev);
+/**
+ *@brief ecore_arfs_mode_configure -
+ *
+ *Enable or disable rfs mode. It must accept atleast one of tcp or udp true
+ *and atleast one of ipv4 or ipv6 true to enable rfs mode.
+ *
+ *@param p_hwfn
+ *@param p_ptt
+ *@param p_cfg_params arfs mode configuration parameters.
+ *
+ */
+void ecore_arfs_mode_configure(struct ecore_hwfn *p_hwfn,
+ struct ecore_ptt *p_ptt,
+ struct ecore_arfs_config_params *p_cfg_params);
+
+/**
+ * @brief - ecore_configure_rfs_ntuple_filter
+ *
+ * This ramrod should be used to add or remove arfs hw filter
+ *
+ * @params p_hwfn
+ * @params p_cb Used for ECORE_SPQ_MODE_CB,where client would initialize
+ * it with cookie and callback function address, if not
+ * using this mode then client must pass NULL.
+ * @params p_addr p_addr is an actual packet header that needs to be
+ * filter. It has to mapped with IO to read prior to
+ * calling this, [contains 4 tuples- src ip, dest ip,
+ * src port, dest port].
+ * @params length length of p_addr header up to past the transport header.
+ * @params qid receive packet will be directed to this queue.
+ * @params vport_id
+ * @params b_is_add flag to add or remove filter.
+ *
+ */
+enum _ecore_status_t
+ecore_configure_rfs_ntuple_filter(struct ecore_hwfn *p_hwfn,
+ struct ecore_spq_comp_cb *p_cb,
+ dma_addr_t p_addr, u16 length,
+ u16 qid, u8 vport_id,
+ bool b_is_add);
#endif
Code Review / deb_dpdk.git / blobdiff