+/* Hey Emacs use -*- mode: C -*- */
/*
* Copyright (c) 2015-2016 Cisco and/or its affiliates.
* Licensed under the Apache License, Version 2.0 (the "License");
* limitations under the License.
*/
-option version = "2.1.0";
+option version = "3.0.0";
+
+import "vnet/ip/ip_types.api";
/** \brief IPsec: Add/delete Security Policy Database
@param client_index - opaque cookie to identify the sender
u32 spd_id;
};
-/** \brief IPsec: Add/delete Security Policy Database entry
+
+enum ipsec_spd_action
+{
+ /* bypass - no IPsec processing */
+ IPSEC_API_SPD_ACTION_BYPASS = 0,
+ /* discard - discard packet with ICMP processing */
+ IPSEC_API_SPD_ACTION_DISCARD,
+ /* resolve - send request to control plane for SA resolving */
+ IPSEC_API_SPD_ACTION_RESOLVE,
+ /* protect - apply IPsec policy using following parameters */
+ IPSEC_API_SPD_ACTION_PROTECT,
+};
+
+/** \brief IPsec: Security Policy Database entry
See RFC 4301, 4.4.1.1 on how to match packet to selectors
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
- @param is_add - add SPD if non-zero, else delete
@param spd_id - SPD instance id (control plane allocated)
@param priority - priority of SPD entry (non-unique value). Used to order SPD matching - higher priorities match before lower
@param is_outbound - entry applies to outbound traffic if non-zero, otherwise applies to inbound traffic
- @param is_ipv6 - remote/local address are IPv6 if non-zero, else IPv4
@param remote_address_start - start of remote address range to match
@param remote_address_stop - end of remote address range to match
@param local_address_start - start of local address range to match
@param local_address_stop - end of local address range to match
- @param protocol - protocol type to match [0 means any]
+ @param protocol - protocol type to match [0 means any] otherwise IANA value
@param remote_port_start - start of remote port range to match ...
@param remote_port_stop - end of remote port range to match [0 to 65535 means ANY, 65535 to 0 means OPAQUE]
@param local_port_start - start of local port range to match ...
@param local_port_stop - end of remote port range to match [0 to 65535 means ANY, 65535 to 0 means OPAQUE]
- @param policy - 0 = bypass (no IPsec processing), 1 = discard (discard packet with ICMP processing), 2 = resolve (send request to control plane for SA resolving, and discard without ICMP processing), 3 = protect (apply IPsec policy using following parameters)
+ @param policy - action to perform on match
@param sa_id - SAD instance id (control plane allocated)
-
*/
-
-autoreply define ipsec_spd_add_del_entry
+typedef ipsec_spd_entry
{
- u32 client_index;
- u32 context;
- u8 is_add;
-
u32 spd_id;
i32 priority;
u8 is_outbound;
- // Selector
- u8 is_ipv6;
- u8 is_ip_any;
- u8 remote_address_start[16];
- u8 remote_address_stop[16];
- u8 local_address_start[16];
- u8 local_address_stop[16];
-
+ u32 sa_id;
+ vl_api_ipsec_spd_action_t policy;
u8 protocol;
+ // Selector
+ vl_api_address_t remote_address_start;
+ vl_api_address_t remote_address_stop;
+ vl_api_address_t local_address_start;
+ vl_api_address_t local_address_stop;
+
u16 remote_port_start;
u16 remote_port_stop;
u16 local_port_start;
u16 local_port_stop;
-
- // Policy
- u8 policy;
- u32 sa_id;
};
-/** \brief IPsec: Add/delete Security Association Database entry
+/** \brief IPsec: Add/delete Security Policy Database entry
+
@param client_index - opaque cookie to identify the sender
@param context - sender context, to match reply w/ request
- @param is_add - add SAD entry if non-zero, else delete
-
- @param sad_id - sad id
-
- @param spi - security parameter index
-
- @param protocol - 0 = AH, 1 = ESP
-
- @param crypto_algorithm - 0 = Null, 1 = AES-CBC-128, 2 = AES-CBC-192, 3 = AES-CBC-256, 4 = 3DES-CBC
- @param crypto_key_length - length of crypto_key in bytes
- @param crypto_key - crypto keying material
-
- @param integrity_algorithm - 0 = None, 1 = MD5-96, 2 = SHA1-96, 3 = SHA-256, 4 = SHA-384, 5=SHA-512
- @param integrity_key_length - length of integrity_key in bytes
- @param integrity_key - integrity keying material
-
- @param use_extended_sequence_number - use ESN when non-zero
-
- @param is_tunnel - IPsec tunnel mode if non-zero, else transport mode
- @param is_tunnel_ipv6 - IPsec tunnel mode is IPv6 if non-zero, else IPv4 tunnel only valid if is_tunnel is non-zero
- @param tunnel_src_address - IPsec tunnel source address IPv6 if is_tunnel_ipv6 is non-zero, else IPv4. Only valid if is_tunnel is non-zero
- @param tunnel_dst_address - IPsec tunnel destination address IPv6 if is_tunnel_ipv6 is non-zero, else IPv4. Only valid if is_tunnel is non-zero
- @param udp_encap - enable UDP encapsulation for NAT traversal
-
- To be added:
- Anti-replay
- IPsec tunnel address copy mode (to support GDOI)
- */
-
-autoreply define ipsec_sad_add_del_entry
+ @param is_add - add SPD if non-zero, else delete
+ @param entry - Description of the entry to add/dell
+*/
+define ipsec_spd_entry_add_del
{
u32 client_index;
u32 context;
u8 is_add;
-
- u32 sad_id;
-
- u32 spi;
-
- u8 protocol;
-
- u8 crypto_algorithm;
- u8 crypto_key_length;
- u8 crypto_key[128];
-
- u8 integrity_algorithm;
- u8 integrity_key_length;
- u8 integrity_key[128];
-
- u8 use_extended_sequence_number;
- u8 use_anti_replay;
-
- u8 is_tunnel;
- u8 is_tunnel_ipv6;
- u8 tunnel_src_address[16];
- u8 tunnel_dst_address[16];
- u8 udp_encap;
+ vl_api_ipsec_spd_entry_t entry;
};
-/** \brief IPsec: Update Security Association keys
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
-
- @param sa_id - sa id
-
- @param crypto_key_length - length of crypto_key in bytes
- @param crypto_key - crypto keying material
+/** \brief IPsec: Reply Add/delete Security Policy Database entry
- @param integrity_key_length - length of integrity_key in bytes
- @param integrity_key - integrity keying material
+ @param context - sender context, to match reply w/ request
+ @param retval - success/fail rutrun code
+ @param stat_index - An index for the policy in the stats segment @ /net/ipec/policy
*/
-
-autoreply define ipsec_sa_set_key
+define ipsec_spd_entry_add_del_reply
{
- u32 client_index;
u32 context;
-
- u32 sa_id;
-
- u8 crypto_key_length;
- u8 crypto_key[128];
-
- u8 integrity_key_length;
- u8 integrity_key[128];
+ i32 retval;
+ u32 stat_index;
};
-/** \brief IKEv2: Add/delete profile
+/** \brief Dump IPsec all SPD IDs
@param client_index - opaque cookie to identify the sender
@param context - sender context, to match reply w/ request
-
- @param name - IKEv2 profile name
- @param is_add - Add IKEv2 profile if non-zero, else delete
*/
-autoreply define ikev2_profile_add_del
-{
+define ipsec_spds_dump {
u32 client_index;
u32 context;
-
- u8 name[64];
- u8 is_add;
};
-/** \brief IKEv2: Set IKEv2 profile authentication method
+/** \brief Dump IPsec all SPD IDs response
@param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
-
- @param name - IKEv2 profile name
- @param auth_method - IKEv2 authentication method (shared-key-mic/rsa-sig)
- @param is_hex - Authentication data in hex format if non-zero, else string
- @param data_len - Authentication data length
- @param data - Authentication data (for rsa-sig cert file path)
+ @param spd_id - SPD instance id (control plane allocated)
+ @param npolicies - number of policies in SPD
*/
-autoreply define ikev2_profile_set_auth
-{
- u32 client_index;
+define ipsec_spds_details {
u32 context;
+ u32 spd_id;
+ u32 npolicies;
+};
- u8 name[64];
- u8 auth_method;
- u8 is_hex;
- u32 data_len;
- u8 data[data_len];
-};
-
-/** \brief IKEv2: Set IKEv2 profile local/remote identification
+/** \brief Dump ipsec policy database data
@param client_index - opaque cookie to identify the sender
@param context - sender context, to match reply w/ request
-
- @param name - IKEv2 profile name
- @param is_local - Identification is local if non-zero, else remote
- @param id_type - Identification type
- @param data_len - Identification data length
- @param data - Identification data
+ @param spd_id - SPD instance id
+ @param sa_id - SA id, optional, set to ~0 to see all policies in SPD
*/
-autoreply define ikev2_profile_set_id
-{
- u32 client_index;
- u32 context;
-
- u8 name[64];
- u8 is_local;
- u8 id_type;
- u32 data_len;
- u8 data[data_len];
+define ipsec_spd_dump {
+ u32 client_index;
+ u32 context;
+ u32 spd_id;
+ u32 sa_id;
};
-/** \brief IKEv2: Set IKEv2 profile traffic selector parameters
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
-
- @param name - IKEv2 profile name
- @param is_local - Traffic selector is local if non-zero, else remote
- @param proto - Traffic selector IP protocol (if zero not relevant)
- @param start_port - The smallest port number allowed by traffic selector
- @param end_port - The largest port number allowed by traffic selector
- @param start_addr - The smallest address included in traffic selector
- @param end_addr - The largest address included in traffic selector
+/** \brief IPsec policy database response
+ @param context - sender context which was passed in the request
+ €param entry - The SPD entry.
+ @param bytes - byte count of packets matching this policy
+ @param packets - count of packets matching this policy
*/
-autoreply define ikev2_profile_set_ts
-{
- u32 client_index;
- u32 context;
-
- u8 name[64];
- u8 is_local;
- u8 proto;
- u16 start_port;
- u16 end_port;
- u32 start_addr;
- u32 end_addr;
+define ipsec_spd_details {
+ u32 context;
+ vl_api_ipsec_spd_entry_t entry;
};
-/** \brief IKEv2: Set IKEv2 local RSA private key
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
-
- @param key_file - Key file absolute path
-*/
-autoreply define ikev2_set_local_key
+/*
+ * @brief Support cryptographic algorithms
+ */
+enum ipsec_crypto_alg
{
- u32 client_index;
- u32 context;
-
- u8 key_file[256];
+ IPSEC_API_CRYPTO_ALG_NONE = 0,
+ IPSEC_API_CRYPTO_ALG_AES_CBC_128,
+ IPSEC_API_CRYPTO_ALG_AES_CBC_192,
+ IPSEC_API_CRYPTO_ALG_AES_CBC_256,
+ IPSEC_API_CRYPTO_ALG_AES_CTR_128,
+ IPSEC_API_CRYPTO_ALG_AES_CTR_192,
+ IPSEC_API_CRYPTO_ALG_AES_CTR_256,
+ IPSEC_API_CRYPTO_ALG_AES_GCM_128,
+ IPSEC_API_CRYPTO_ALG_AES_GCM_192,
+ IPSEC_API_CRYPTO_ALG_AES_GCM_256,
+ IPSEC_API_CRYPTO_ALG_DES_CBC,
+ IPSEC_API_CRYPTO_ALG_3DES_CBC,
};
-/** \brief IKEv2: Set IKEv2 responder interface and IP address
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
-
- @param name - IKEv2 profile name
- @param sw_if_index - interface index
- @param address - interface address
-*/
-autoreply define ikev2_set_responder
+/*
+ * @brief Supported Integrity Algorithms
+ */
+enum ipsec_integ_alg
{
- u32 client_index;
- u32 context;
-
- u8 name[64];
- u32 sw_if_index;
- u8 address[4];
+ IPSEC_API_INTEG_ALG_NONE = 0,
+ /* RFC2403 */
+ IPSEC_API_INTEG_ALG_MD5_96,
+ /* RFC2404 */
+ IPSEC_API_INTEG_ALG_SHA1_96,
+ /* draft-ietf-ipsec-ciph-sha-256-00 */
+ IPSEC_API_INTEG_ALG_SHA_256_96,
+ /* RFC4868 */
+ IPSEC_API_INTEG_ALG_SHA_256_128,
+ /* RFC4868 */
+ IPSEC_API_INTEG_ALG_SHA_384_192,
+ /* RFC4868 */
+ IPSEC_API_INTEG_ALG_SHA_512_256,
+};
+
+enum ipsec_sad_flags
+{
+ IPSEC_API_SAD_FLAG_NONE = 0,
+ /* Enable extended sequence numbers */
+ IPSEC_API_SAD_FLAG_USE_ESN = 0x01,
+ /* Enable Anti-replay */
+ IPSEC_API_SAD_FLAG_USE_ANTI_REPLAY = 0x02,
+ /* IPsec tunnel mode if non-zero, else transport mode */
+ IPSEC_API_SAD_FLAG_IS_TUNNEL = 0x04,
+ /* IPsec tunnel mode is IPv6 if non-zero,
+ * else IPv4 tunnel only valid if is_tunnel is non-zero */
+ IPSEC_API_SAD_FLAG_IS_TUNNEL_V6 = 0x08,
+ /* enable UDP encapsulation for NAT traversal */
+ IPSEC_API_SAD_FLAG_UDP_ENCAP = 0x10,
+};
+
+enum ipsec_proto
+{
+ IPSEC_API_PROTO_ESP,
+ IPSEC_API_PROTO_AH,
};
-/** \brief IKEv2: Set IKEv2 IKE transforms in SA_INIT proposal (RFC 7296)
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
-
- @param name - IKEv2 profile name
- @param crypto_alg - encryption algorithm
- @param crypto_key_size - encryption key size
- @param integ_alg - integrity algorithm
- @param dh_group - Diffie-Hellman group
-
-*/
-autoreply define ikev2_set_ike_transforms
+typedef key
{
- u32 client_index;
- u32 context;
-
- u8 name[64];
- u32 crypto_alg;
- u32 crypto_key_size;
- u32 integ_alg;
- u32 dh_group;
+ /* the length of the key */
+ u8 length;
+ /* The data for the key */
+ u8 data[128];
};
-/** \brief IKEv2: Set IKEv2 ESP transforms in SA_INIT proposal (RFC 7296)
+/** \brief IPsec: Security Association Database entry
@param client_index - opaque cookie to identify the sender
@param context - sender context, to match reply w/ request
-
- @param name - IKEv2 profile name
- @param crypto_alg - encryption algorithm
- @param crypto_key_size - encryption key size
- @param integ_alg - integrity algorithm
- @param dh_group - Diffie-Hellman group
-
-*/
-autoreply define ikev2_set_esp_transforms
+ @param is_add - add SAD entry if non-zero, else delete
+ @param sad_id - sad id
+ @param spi - security parameter index
+ @param protocol - 0 = AH, 1 = ESP
+ @param crypto_algorithm - a supported crypto algorithm
+ @param crypto_key - crypto keying material
+ @param integrity_algorithm - one of the supported algorithms
+ @param integrity_key - integrity keying material
+ @param tunnel_src_address - IPsec tunnel source address IPv6 if is_tunnel_ipv6 is non-zero, else IPv4. Only valid if is_tunnel is non-zero
+ @param tunnel_dst_address - IPsec tunnel destination address IPv6 if is_tunnel_ipv6 is non-zero, else IPv4. Only valid if is_tunnel is non-zero
+ @param tx_table_id - the FIB id used for encapsulated packets
+ @param salt - for use with counter mode ciphers
+ */
+typedef ipsec_sad_entry
{
- u32 client_index;
- u32 context;
-
- u8 name[64];
- u32 crypto_alg;
- u32 crypto_key_size;
- u32 integ_alg;
- u32 dh_group;
-};
+ u32 sad_id;
-/** \brief IKEv2: Set Child SA lifetime, limited by time and/or data
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
+ u32 spi;
- @param name - IKEv2 profile name
- @param lifetime - SA maximum life time in seconds (0 to disable)
- @param lifetime_jitter - Jitter added to prevent simultaneous rekeying
- @param handover - Hand over time
- @param lifetime_maxdata - SA maximum life time in bytes (0 to disable)
-
-*/
-autoreply define ikev2_set_sa_lifetime
-{
- u32 client_index;
- u32 context;
+ vl_api_ipsec_proto_t protocol;
- u8 name[64];
- u64 lifetime;
- u32 lifetime_jitter;
- u32 handover;
- u64 lifetime_maxdata;
-};
+ vl_api_ipsec_crypto_alg_t crypto_algorithm;
+ vl_api_key_t crypto_key;
-/** \brief IKEv2: Initiate the SA_INIT exchange
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
+ vl_api_ipsec_integ_alg_t integrity_algorithm;
+ vl_api_key_t integrity_key;
- @param name - IKEv2 profile name
-
-*/
-autoreply define ikev2_initiate_sa_init
-{
- u32 client_index;
- u32 context;
+ vl_api_ipsec_sad_flags_t flags;
- u8 name[64];
+ vl_api_address_t tunnel_src;
+ vl_api_address_t tunnel_dst;
+ u32 tx_table_id;
+ u32 salt;
};
-/** \brief IKEv2: Initiate the delete IKE SA exchange
+/** \brief IPsec: Add/delete Security Association Database entry
@param client_index - opaque cookie to identify the sender
@param context - sender context, to match reply w/ request
-
- @param ispi - IKE SA initiator SPI
-
-*/
-autoreply define ikev2_initiate_del_ike_sa
+ @param entry - Entry to add or delete
+ */
+define ipsec_sad_entry_add_del
{
u32 client_index;
u32 context;
-
- u64 ispi;
+ u8 is_add;
+ vl_api_ipsec_sad_entry_t entry;
};
-
-/** \brief IKEv2: Initiate the delete Child SA exchange
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
-
- @param ispi - Child SA initiator SPI
-
-*/
-autoreply define ikev2_initiate_del_child_sa
+define ipsec_sad_entry_add_del_reply
{
- u32 client_index;
u32 context;
-
- u32 ispi;
+ i32 retval;
+ u32 stat_index;
};
-/** \brief IKEv2: Initiate the rekey Child SA exchange
+/** \brief IPsec: Update Security Association keys
@param client_index - opaque cookie to identify the sender
@param context - sender context, to match reply w/ request
- @param ispi - Child SA initiator SPI
-
-*/
-autoreply define ikev2_initiate_rekey_child_sa
-{
- u32 client_index;
- u32 context;
-
- u32 ispi;
-};
+ @param sa_id - sa id
-/** \brief Dump IPsec all SPD IDs
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
+ @param crypto_key - crypto keying material
+ @param integrity_key - integrity keying material
*/
-define ipsec_spds_dump {
- u32 client_index;
- u32 context;
-};
-/** \brief Dump IPsec all SPD IDs response
- @param client_index - opaque cookie to identify the sender
- @param spd_id - SPD instance id (control plane allocated)
- @param npolicies - number of policies in SPD
-*/
-define ipsec_spds_details {
+autoreply define ipsec_sa_set_key
+{
+ u32 client_index;
u32 context;
- u32 spd_id;
- u32 npolicies;
-};
-/** \brief Dump ipsec policy database data
- @param client_index - opaque cookie to identify the sender
- @param context - sender context, to match reply w/ request
- @param spd_id - SPD instance id
- @param sa_id - SA id, optional, set to ~0 to see all policies in SPD
-*/
-define ipsec_spd_dump {
- u32 client_index;
- u32 context;
- u32 spd_id;
- u32 sa_id;
-};
+ u32 sa_id;
-/** \brief IPsec policy database response
- @param context - sender context which was passed in the request
- @param spd_id - SPD instance id
- @param priority - numeric value to control policy evaluation order
- @param is_outbound - [1|0] to indicate if direction is [out|in]bound
- @param is_ipv6 - [1|0] to indicate if address family is ipv[6|4]
- @param local_start_addr - first address in local traffic selector range
- @param local_stop_addr - last address in local traffic selector range
- @param local_start_port - first port in local traffic selector range
- @param local_stop_port - last port in local traffic selector range
- @param remote_start_addr - first address in remote traffic selector range
- @param remote_stop_addr - last address in remote traffic selector range
- @param remote_start_port - first port in remote traffic selector range
- @param remote_stop_port - last port in remote traffic selector range
- @param protocol - traffic selector protocol
- @param policy - policy action
- @param sa_id - SA id
- @param bytes - byte count of packets matching this policy
- @param packets - count of packets matching this policy
-*/
-define ipsec_spd_details {
- u32 context;
- u32 spd_id;
- i32 priority;
- u8 is_outbound;
- u8 is_ipv6;
- u8 local_start_addr[16];
- u8 local_stop_addr[16];
- u16 local_start_port;
- u16 local_stop_port;
- u8 remote_start_addr[16];
- u8 remote_stop_addr[16];
- u16 remote_start_port;
- u16 remote_stop_port;
- u8 protocol;
- u8 policy;
- u32 sa_id;
- u64 bytes;
- u64 packets;
+ vl_api_key_t crypto_key;
+ vl_api_key_t integrity_key;
};
/** \brief IPsec: Get SPD interfaces
@param client_index - opaque cookie to identify the sender
@param context - sender context, to match reply w/ request
@param is_add - add IPsec tunnel interface if nonzero, else delete
+ @param is_ip6 - tunnel v6 or v4
@param esn - enable extended sequence numbers if nonzero, else disable
@param anti_replay - enable anti replay check if nonzero, else disable
@param local_ip - local IP address
@param show_instance - instance to display for intf if renumber is set
@param udp_encap - enable UDP encapsulation for NAT traversal
@param tx_table_id - the FIB id used after packet encap
+ @param salt - for use with counter mode ciphers
*/
define ipsec_tunnel_if_add_del {
u32 client_index;
u8 is_add;
u8 esn;
u8 anti_replay;
- u8 local_ip[4];
- u8 remote_ip[4];
+ vl_api_address_t local_ip;
+ vl_api_address_t remote_ip;
u32 local_spi;
u32 remote_spi;
u8 crypto_alg;
u32 show_instance;
u8 udp_encap;
u32 tx_table_id;
+ u32 salt;
};
/** \brief Add/delete IPsec tunnel interface response
@param replay_window - bit map of seq nums received relative to last_seq if using anti-replay
@param total_data_size - total bytes sent or received
@param udp_encap - 1 if UDP encap enabled, 0 otherwise
- @param tx_table_id - the FIB id used for encapsulated packets
*/
define ipsec_sa_details {
u32 context;
- u32 sa_id;
- u32 sw_if_index;
-
- u32 spi;
- u8 protocol;
-
- u8 crypto_alg;
- u8 crypto_key_len;
- u8 crypto_key[128];
-
- u8 integ_alg;
- u8 integ_key_len;
- u8 integ_key[128];
-
- u8 use_esn;
- u8 use_anti_replay;
-
- u8 is_tunnel;
- u8 is_tunnel_ip6;
- u8 tunnel_src_addr[16];
- u8 tunnel_dst_addr[16];
+ vl_api_ipsec_sad_entry_t entry;
+ u32 sw_if_index;
u32 salt;
u64 seq_outbound;
u64 last_seq_inbound;
u64 replay_window;
u64 total_data_size;
- u8 udp_encap;
-
- u32 tx_table_id;
};
/** \brief Set key on IPsec interface
define ipsec_backend_details {
u32 context;
u8 name[128];
- u8 protocol;
+ vl_api_ipsec_proto_t protocol;
u8 index;
u8 active;
};
autoreply define ipsec_select_backend {
u32 client_index;
u32 context;
- u8 protocol;
+ vl_api_ipsec_proto_t protocol;
u8 index;
};