*** Settings ***
| Resource | resources/libraries/robot/performance/performance_setup.robot
-| Library | resources.libraries.python.QemuUtils
| ...
| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
| ... | NIC_Intel-X520-DA2 | DOT1Q | L2BDMACLRN | BASE | VHOST | 1VM
| ...
| Test Template | Local Template
| ...
-| Documentation | *Raw results L2BD test cases with vhost*
+| Documentation | *Raw results L2BD with vhost and IEEE 802.1Q test cases*
| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. 802.1q
-| ... | tagging is applied on link between DUT1 and DUT2.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-
-| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via
-| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting
-| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M
-| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores
-| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to
-| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520
-| ... | Niantic by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\
+| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via\
+| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting\
+| ... | vhost-user interfaces, forwarding mode is set to io, rxd/txd=1024.\
+| ... | DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
-| ${perf_qemu_qsz}= | 1024
| ${subid}= | 10
| ${tag_rewrite}= | pop-1
| ${overhead}= | ${4}
# Socket names
| ${bd_id1}= | 1
| ${bd_id2}= | 2
-| ${sock1}= | /tmp/sock-1-${bd_id1}
-| ${sock2}= | /tmp/sock-1-${bd_id2}
+| ${sock1}= | /var/run/vpp/sock-1-${bd_id1}
+| ${sock2}= | /var/run/vpp/sock-1-${bd_id2}
# X520-DA2 bandwidth limit
| ${s_limit}= | ${10000000000}
# Traffic profile:
*** Keywords ***
| Local Template
| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config.
-| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
| | ... | trial throughput test.
| | ...
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User and VLAN in a 3-node circular topology
+| | When Initialize L2 bridge domains with Vhost-User and VLAN in circular topology
| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
| | ... | ${tag_rewrite}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | ... | jumbo_frames=${jumbo}
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | ... | jumbo_frames=${jumbo}
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
+| | And Configure guest VMs with dpdk-testpmd connected via vhost-user
+| | ... | vm_count=${1} | jumbo=${jumbo} | perf_qemu_qsz=${1024}
+| | ... | use_tuned_cfs=${False}
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}