X-Git-Url: https://gerrit.fd.io/r/gitweb?a=blobdiff_plain;ds=sidebyside;f=docs%2Fietf%2Fdraft-ietf-bmwg-mlrsearch-00.md;fp=docs%2Fietf%2Fdraft-ietf-bmwg-mlrsearch-00.md;h=0000000000000000000000000000000000000000;hb=52f109b0e14b5f192e2b7f0573e6cebb601d0651;hp=05bc41f0fa65d6e9fff5f667dee81a33cc3f1484;hpb=8f9290d1594d35eb838c0c4c9d754b80a35e4a3a;p=csit.git diff --git a/docs/ietf/draft-ietf-bmwg-mlrsearch-00.md b/docs/ietf/draft-ietf-bmwg-mlrsearch-00.md deleted file mode 100644 index 05bc41f0fa..0000000000 --- a/docs/ietf/draft-ietf-bmwg-mlrsearch-00.md +++ /dev/null @@ -1,556 +0,0 @@ ---- -title: Multiple Loss Ratio Search for Packet Throughput (MLRsearch) -# abbrev: MLRsearch -docname: draft-ietf-bmwg-mlrsearch-00 -date: 2021-02-05 - -ipr: trust200902 -area: ops -wg: Benchmarking Working Group -kw: Internet-Draft -cat: info - -coding: us-ascii -pi: # can use array (if all yes) or hash here -# - toc -# - sortrefs -# - symrefs - toc: yes - sortrefs: # defaults to yes - symrefs: yes - -author: - - - ins: M. Konstantynowicz - name: Maciek Konstantynowicz - org: Cisco Systems - role: editor - email: mkonstan@cisco.com - - - ins: V. Polak - name: Vratko Polak - org: Cisco Systems - role: editor - email: vrpolak@cisco.com - -normative: - RFC2544: - RFC8174: - -informative: - FDio-CSIT-MLRsearch: - target: https://docs.fd.io/csit/rls2001/report/introduction/methodology_data_plane_throughput/methodology_mlrsearch_tests.html - title: "FD.io CSIT Test Methodology - MLRsearch" - date: 2020-02 - PyPI-MLRsearch: - target: https://pypi.org/project/MLRsearch/0.3.0/ - title: "MLRsearch 0.3.0, Python Package Index" - date: 2020-02 - ---- abstract - -This document proposes changes to [RFC2544], specifically to packet -throughput search methodology, by defining a new search algorithm -referred to as Multiple Loss Ratio search (MLRsearch for short). Instead -of relying on binary search with pre-set starting offered load, it -proposes a novel approach discovering the starting point in the initial -phase, and then searching for packet throughput based on defined packet -loss ratio (PLR) input criteria and defined final trial duration time. -One of the key design principles behind MLRsearch is minimizing the -total test duration and searching for multiple packet throughput rates -(each with a corresponding PLR) concurrently, instead of doing it -sequentially. - -The main motivation behind MLRsearch is the new set of challenges and -requirements posed by NFV (Network Function Virtualization), -specifically software based implementations of NFV data planes. Using -[RFC2544] in the experience of the authors yields often not repetitive -and not replicable end results due to a large number of factors that are -out of scope for this draft. MLRsearch aims to address this challenge -in a simple way of getting the same result sooner, so more repetitions -can be done to describe the replicability. - ---- middle - -# Terminology - -* Frame size: size of an Ethernet Layer-2 frame on the wire, including - any VLAN tags (dot1q, dot1ad) and Ethernet FCS, but excluding Ethernet - preamble and inter-frame gap. Measured in bytes. -* Packet size: same as frame size, both terms used interchangeably. -* Device Under Test (DUT): In software networking, "device" denotes a - specific piece of software tasked with packet processing. Such device - is surrounded with other software components (such as operating system - kernel). It is not possible to run devices without also running the - other components, and hardware resources are shared between both. For - purposes of testing, the whole set of hardware and software components - is called "system under test" (SUT). As SUT is the part of the whole - test setup performance of which can be measured by [RFC2544] methods, - this document uses SUT instead of [RFC2544] DUT. Device under test - (DUT) can be re-introduced when analysing test results using whitebox - techniques, but this document sticks to blackbox testing. -* System Under Test (SUT): System under test (SUT) is a part of the - whole test setup whose performance is to be benchmarked. The complete - test setup contains other parts, whose performance is either already - established, or not affecting the benchmarking result. -* Bi-directional throughput tests: involve packets/frames flowing in - both transmit and receive directions over every tested interface of - SUT/DUT. Packet flow metrics are measured per direction, and can be - reported as aggregate for both directions and/or separately - for each measured direction. In most cases bi-directional tests - use the same (symmetric) load in both directions. -* Uni-directional throughput tests: involve packets/frames flowing in - only one direction, i.e. either transmit or receive direction, over - every tested interface of SUT/DUT. Packet flow metrics are measured - and are reported for measured direction. -* Packet Loss Ratio (PLR): ratio of packets received relative to packets - transmitted over the test trial duration, calculated using formula: - PLR = ( pkts_transmitted - pkts_received ) / pkts_transmitted. - For bi-directional throughput tests aggregate PLR is calculated based - on the aggregate number of packets transmitted and received. -* Packet Throughput Rate: maximum packet offered load DUT/SUT forwards - within the specified Packet Loss Ratio (PLR). In many cases the rate - depends on the frame size processed by DUT/SUT. Hence packet - throughput rate MUST be quoted with specific frame size as received by - DUT/SUT during the measurement. For bi-directional tests, packet - throughput rate should be reported as aggregate for both directions. - Measured in packets-per-second (pps) or frames-per-second (fps), - equivalent metrics. -* Bandwidth Throughput Rate: a secondary metric calculated from packet - throughput rate using formula: bw_rate = pkt_rate * (frame_size + - L1_overhead) * 8, where L1_overhead for Ethernet includes preamble (8 - Bytes) and inter-frame gap (12 Bytes). For bi-directional tests, - bandwidth throughput rate should be reported as aggregate for both - directions. Expressed in bits-per-second (bps). -* Non Drop Rate (NDR): maximum packet/bandwith throughput rate sustained - by DUT/SUT at PLR equal zero (zero packet loss) specific to tested - frame size(s). MUST be quoted with specific packet size as received by - DUT/SUT during the measurement. Packet NDR measured in - packets-per-second (or fps), bandwidth NDR expressed in - bits-per-second (bps). -* Partial Drop Rate (PDR): maximum packet/bandwith throughput rate - sustained by DUT/SUT at PLR greater than zero (non-zero packet loss) - specific to tested frame size(s). MUST be quoted with specific packet - size as received by DUT/SUT during the measurement. Packet PDR - measured in packets-per-second (or fps), bandwidth PDR expressed in - bits-per-second (bps). -* Maximum Receive Rate (MRR): packet/bandwidth rate regardless of PLR - sustained by DUT/SUT under specified Maximum Transmit Rate (MTR) - packet load offered by traffic generator. MUST be quoted with both - specific packet size and MTR as received by DUT/SUT during the - measurement. Packet MRR measured in packets-per-second (or fps), - bandwidth MRR expressed in bits-per-second (bps). -* Trial: a single measurement step. See [RFC2544] section 23. -* Trial duration: amount of time over which packets are transmitted - in a single measurement step. - -# MLRsearch Background - -Multiple Loss Ratio search (MLRsearch) is a packet throughput search -algorithm suitable for deterministic systems (as opposed to -probabilistic systems). MLRsearch discovers multiple packet throughput -rates in a single search, with each rate associated with a distinct -Packet Loss Ratio (PLR) criteria. - -For cases when multiple rates need to be found, this property makes -MLRsearch more efficient in terms of time execution, compared to -traditional throughput search algorithms that discover a single packet -rate per defined search criteria (e.g. a binary search specified by -[RFC2544]). MLRsearch reduces execution time even further by relying on -shorter trial durations of intermediate steps, with only the final -measurements conducted at the specified final trial duration. This -results in the shorter overall search execution time when compared to a -traditional binary search, while guaranteeing the same results for -deterministic systems. - -In practice two rates with distinct PLRs are commonly used for packet -throughput measurements of NFV systems: Non Drop Rate (NDR) with PLR=0 -and Partial Drop Rate (PDR) with PLR>0. The rest of this document -describes MLRsearch for NDR and PDR. If needed, MLRsearch can be -adapted to discover more throughput rates with different pre-defined -PLRs. - -Similarly to other throughput search approaches like binary search, -MLRsearch is effective for SUTs/DUTs with PLR curve that is continuously -flat or increasing with growing offered load. It may not be as -effective for SUTs/DUTs with abnormal PLR curves. - -MLRsearch relies on traffic generator to qualify the received packet -stream as error-free, and invalidate the results if any disqualifying -errors are present e.g. out-of-sequence frames. - -MLRsearch can be applied to both uni-directional and bi-directional -throughput tests. - -For bi-directional tests, MLRsearch rates and ratios are aggregates of -both directions, based on the following assumptions: - -* Traffic transmitted by traffic generator and received by SUT/DUT - has the same packet rate in each direction, - in other words the offered load is symmetric. -* SUT/DUT packet processing capacity is the same in both directions, - resulting in the same packet loss under load. - -# MLRsearch Overview - -The main properties of MLRsearch: - -* MLRsearch is a duration aware multi-phase multi-rate search algorithm: - * Initial Phase determines promising starting interval for the search. - * Intermediate Phases progress towards defined final search criteria. - * Final Phase executes measurements according to the final search - criteria. - * Final search criteria are defined by following inputs: - * PLRs associated with NDR and PDR. - * Final trial duration. - * Measurement resolution. -* Initial Phase: - * Measure MRR over initial trial duration. - * Measured MRR is used as an input to the first intermediate phase. -* Multiple Intermediate Phases: - * Trial duration: - * Start with initial trial duration in the first intermediate phase. - * Converge geometrically towards the final trial duration. - * Track two values for NDR and two for PDR: - * The values are called lower_bound and upper_bound. - * Each value comes from a specific trial measurement: - * Most recent for that transmit rate. - * As such the value is associated with that measurement's duration - and loss. - * A bound can be valid or invalid: - * Valid lower_bound must conform with PLR search criteria. - * Valid upper_bound must not conform with PLR search criteria. - * Example of invalid NDR lower_bound is if it has been measured - with non-zero loss. - * Invalid bounds are not real boundaries for the searched value: - * They are needed to track interval widths. - * Valid bounds are real boundaries for the searched value. - * Each non-initial phase ends with all bounds valid. - * Bound can become invalid if it re-measured at a longer trial - duration in a sub-sequent phase. - * Search: - * Start with a large (lower_bound, upper_bound) interval width, that - determines measurement resolution. - * Geometrically converge towards the width goal of the phase. - * Each phase halves the previous width goal. - * First measurement of the next phase will be internal search - which always gives a valid bound and brings the width to the new goal. - * Only one bound then needs to be re-measured with new duration. - * Use of internal and external searches: - * External search: - * Measures at transmit rates outside the (lower_bound, - upper_bound) interval. - * Activated when a bound is invalid, to search for a new valid - bound by multiplying (for example doubling) the interval width. - * It is a variant of "exponential search". - * Internal search: - * A "binary search" that measures at transmit rates within the - (lower_bound, upper_bound) valid interval, halving the interval - width. -* Final Phase: - * Executed with the final test trial duration, and the final width - goal that determines resolution of the overall search. -* Intermediate Phases together with the Final Phase are called - Non-Initial Phases. - -The main benefits of MLRsearch vs. binary search include: - -* In general MLRsearch is likely to execute more trials overall, but - likely less trials at a set final trial duration. -* In well behaving cases, e.g. when results do not depend on trial - duration, it greatly reduces (>50%) the overall duration compared to a - single PDR (or NDR) binary search over duration, while finding - multiple drop rates. -* In all cases MLRsearch yields the same or similar results to binary - search. -* Note: both binary search and MLRsearch are susceptible to reporting - non-repeatable results across multiple runs for very bad behaving - cases. - -Caveats: - -* Worst case MLRsearch can take longer than a binary search e.g. in case of - drastic changes in behaviour for trials at varying durations. - -# Sample Implementation - -Following is a brief description of a sample MLRsearch implementation, -which is a simlified version of the existing implementation. - -## Input Parameters - -1. **maximum_transmit_rate** - Maximum Transmit Rate (MTR) of packets to - be used by external traffic generator implementing MLRsearch, - limited by the actual Ethernet link(s) rate, NIC model or traffic - generator capabilities. -2. **minimum_transmit_rate** - minimum packet transmit rate to be used for - measurements. MLRsearch fails if lower transmit rate needs to be - used to meet search criteria. -3. **final_trial_duration** - required trial duration for final rate - measurements. -4. **initial_trial_duration** - trial duration for initial MLRsearch phase. -5. **final_relative_width** - required measurement resolution expressed as - (lower_bound, upper_bound) interval width relative to upper_bound. -6. **packet_loss_ratio** - maximum acceptable PLR search criterion for - PDR measurements. -7. **number_of_intermediate_phases** - number of phases between the initial - phase and the final phase. Impacts the overall MLRsearch duration. - Less phases are required for well behaving cases, more phases - may be needed to reduce the overall search duration for worse behaving cases. - -## Initial Phase - -1. First trial measures at configured maximum transmit rate (MTR) and - discovers maximum receive rate (MRR). - * IN: trial_duration = initial_trial_duration. - * IN: offered_transmit_rate = maximum_transmit_rate. - * DO: single trial. - * OUT: measured loss ratio. - * OUT: MRR = measured receive rate. - If loss ratio is zero, MRR is set below MTR so that interval width is equal - to the width goal of the first intermediate phase. -2. Second trial measures at MRR and discovers MRR2. - * IN: trial_duration = initial_trial_duration. - * IN: offered_transmit_rate = MRR. - * DO: single trial. - * OUT: measured loss ratio. - * OUT: MRR2 = measured receive rate. - If loss ratio is zero, MRR2 is set above MRR so that interval width is equal - to the width goal of the first intermediate phase. - MRR2 could end up being equal to MTR (for example if both measurements so far - had zero loss), which was already measured, step 3 is skipped in that case. -3. Third trial measures at MRR2. - * IN: trial_duration = initial_trial_duration. - * IN: offered_transmit_rate = MRR2. - * DO: single trial. - * OUT: measured loss ratio. - -## Non-Initial Phases - -1. Main loop: - 1. IN: trial_duration for the current phase. Set to - initial_trial_duration for the first intermediate phase; to - final_trial_duration for the final phase; or to the element of - interpolating geometric sequence for other intermediate phases. - For example with two intermediate phases, trial_duration of the - second intermediate phase is the geometric average of - initial_trial_duration and final_trial_duration. - 2. IN: relative_width_goal for the current phase. Set to - final_relative_width for the final phase; doubled for each - preceding phase. For example with two intermediate phases, the - first intermediate phase uses quadruple of final_relative_width - and the second intermediate phase uses double of - final_relative_width. - 3. IN: ndr_interval, pdr_interval from the previous main loop - iteration or the previous phase. If the previous phase is the - initial phase, both intervals are formed by a (correctly ordered) - pair of MRR2 and MRR. Note that the initial phase is likely - to create intervals with invalid bounds. - 4. DO: According to the procedure described in point 2., either exit - the phase (by jumping to 1.7.), or calculate new transmit rate to - measure with. - 5. DO: Perform the trial measurement at the new transmit rate and - trial_duration, compute its loss ratio. - 6. DO: Update the bounds of both intervals, based on the new - measurement. The actual update rules are numerous, as NDR external - search can affect PDR interval and vice versa, but the result - agrees with rules of both internal and external search. For - example, any new measurement below an invalid lower_bound becomes - the new lower_bound, while the old measurement (previously acting - as the invalid lower_bound) becomes a new and valid upper_bound. - Go to next iteration (1.3.), taking the updated intervals as new - input. - 7. OUT: current ndr_interval and pdr_interval. In the final phase - this is also considered to be the result of the whole search. For - other phases, the next phase loop is started with the current - results as an input. -2. New transmit rate (or exit) calculation (for point 1.4.): - 1. If there is an invalid bound then prepare for external search: - * IF the most recent measurement at NDR lower_bound transmit - rate had the loss higher than zero, then the new transmit rate - is NDR lower_bound decreased by two NDR interval widths. - * Else, IF the most recent measurement at PDR lower_bound - transmit rate had the loss higher than PLR, then the new - transmit rate is PDR lower_bound decreased by two PDR interval - widths. - * Else, IF the most recent measurement at NDR upper_bound - transmit rate had no loss, then the new transmit rate is NDR - upper_bound increased by two NDR interval widths. - * Else, IF the most recent measurement at PDR upper_bound - transmit rate had the loss lower or equal to PLR, then the new - transmit rate is PDR upper_bound increased by two PDR interval - widths. - 2. Else, if interval width is higher than the current phase goal: - * IF NDR interval does not meet the current phase width - goal, prepare for internal search. The new transmit rate is a - in the middle of NDR lower_bound and NDR upper_bound. - * IF PDR interval does not meet the current phase width - goal, prepare for internal search. The new transmit rate is a - in the middle of PDR lower_bound and PDR upper_bound. - 3. Else, if some bound has still only been measured at a lower - duration, prepare to re-measure at the current duration (and the - same transmit rate). The order of priorities is: - * NDR lower_bound, - * PDR lower_bound, - * NDR upper_bound, - * PDR upper_bound. - 4. Else, do not prepare any new rate, to exit the phase. - This ensures that at the end of each non-initial phase - all intervals are valid, narrow enough, and measured - at current phase trial duration. - -# FD.io CSIT Implementation - -The only known working implementation of MLRsearch is in -the open-source code running in Linux Foundation -FD.io CSIT project [FDio-CSIT-MLRsearch] as part of -a Continuous Integration / Continuous Development (CI/CD) framework. - -MLRsearch is also available as a Python package in [PyPI-MLRsearch]. - -## Additional details - -This document so far has been describing a simplified version of -MLRsearch algorithm. The full algorithm as implemented in CSIT contains -additional logic, which makes some of the details (but not general -ideas) above incorrect. Here is a short description of the additional -logic as a list of principles, explaining their main differences from -(or additions to) the simplified description, but without detailing -their mutual interaction. - -1. Logarithmic transmit rate. - * In order to better fit the relative width goal, the interval - doubling and halving is done differently. - * For example, the middle of 2 and 8 is 4, not 5. -2. Optimistic maximum rate. - * The increased rate is never higher than the maximum rate. - * Upper bound at that rate is always considered valid. -3. Pessimistic minimum rate. - * The decreased rate is never lower than the minimum rate. - * If a lower bound at that rate is invalid, a phase stops refining - the interval further (until it gets re-measured). -4. Conservative interval updates. - * Measurements above the current upper bound never update a valid upper - bound, even if drop ratio is low. - * Measurements below the current lower bound always update any lower - bound if drop ratio is high. -5. Ensure sufficient interval width. - * Narrow intervals make external search take more time to find a - valid bound. - * If the new transmit increased or decreased rate would result in - width less than the current goal, increase/decrease more. - * This can happen if the measurement for the other interval - makes the current interval too narrow. - * Similarly, take care the measurements in the initial phase create - wide enough interval. -6. Timeout for bad cases. - * The worst case for MLRsearch is when each phase converges to - intervals way different than the results of the previous phase. - * Rather than suffer total search time several times larger than pure - binary search, the implemented tests fail themselves when the - search takes too long (given by argument *timeout*). -7. Pessimistic external search. - * Valid bound becoming invalid on re-measurement with higher duration - is frequently a sign of SUT behaving in non-deterministic way - (from blackbox point of view). If the final width interval goal - is too narrow compared to width of rate region where SUT - is non-deterministic, it is quite likely that there will be multiple - invalid bounds before the external search finds a valid one. - * In this case, external search can be sped up by increasing interval width - more rapidly. As only powers of two ensure the subsequent internal search - will not result in needlessly narrow interval, a parameter *doublings* - is introduced to control the pessimism of external search. - For example three doublings result in interval width being multiplied - by eight in each external search iteration. - -### FD.io CSIT Input Parameters - -1. **maximum_transmit_rate** - Typical values: 2 * 14.88 Mpps for 64B - 10GE link rate, 2 * 18.75 Mpps for 64B 40GE NIC (specific model). -2. **minimum_transmit_rate** - Value: 2 * 10 kpps (traffic generator - limitation). -3. **final_trial_duration** - Value: 30 seconds. -4. **initial_trial_duration** - Value: 1 second. -5. **final_relative_width** - Value: 0.005 (0.5%). -6. **packet_loss_ratio** - Value: 0.005 (0.5%). -7. **number_of_intermediate_phases** - Value: 2. - The value has been chosen based on limited experimentation to date. - More experimentation needed to arrive to clearer guidelines. -8. **timeout** - Limit for the overall search duration (for one search). - If MLRsearch oversteps this limit, it immediatelly declares the test failed, - to avoid wasting even more time on a misbehaving SUT. - Value: 600 (seconds). -9. **doublings** - Number of dublings when computing new interval width - in external search. - Value: 2 (interval width is quadroupled). - Value of 1 is best for well-behaved SUTs, but value of 2 has been found - to decrease overall search time for worse-behaved SUT configurations, - contributing more to the overall set of different SUT configurations tested. - -## Example MLRsearch Run - -The following table shows data from a real test run in CSIT -(using the default input values as above). -The first column is the phase, the second is the trial measurement performed -(aggregate bidirectional offered load in megapackets per second, -and trial duration in seconds). -Each of last four columns show one bound as updated after the measurement -(duration truncated to save space). -Loss ratio is not shown, but invalid bounds are marked with a plus sign. - -| Phase | Trial | NDR lower | NDR upper | PDR lower | PDR upper | -| ----: | ---------: | --------: | --------: | --------: | --------: | -| init. | 37.50 1.00 | N/A | 37.50 1. | N/A | 37.50 1. | -| init. | 10.55 1.00 | +10.55 1. | 37.50 1. | +10.55 1. | 37.50 1. | -| init. | 9.437 1.00 | +9.437 1. | 10.55 1. | +9.437 1. | 10.55 1. | -| int 1 | 6.053 1.00 | 6.053 1. | 9.437 1. | 6.053 1. | 9.437 1. | -| int 1 | 7.558 1.00 | 7.558 1. | 9.437 1. | 7.558 1. | 9.437 1. | -| int 1 | 8.446 1.00 | 8.446 1. | 9.437 1. | 8.446 1. | 9.437 1. | -| int 1 | 8.928 1.00 | 8.928 1. | 9.437 1. | 8.928 1. | 9.437 1. | -| int 1 | 9.179 1.00 | 8.928 1. | 9.179 1. | 9.179 1. | 9.437 1. | -| int 1 | 9.052 1.00 | 9.052 1. | 9.179 1. | 9.179 1. | 9.437 1. | -| int 1 | 9.307 1.00 | 9.052 1. | 9.179 1. | 9.179 1. | 9.307 1. | -| int 2 | 9.115 5.48 | 9.115 5. | 9.179 1. | 9.179 1. | 9.307 1. | -| int 2 | 9.243 5.48 | 9.115 5. | 9.179 1. | 9.243 5. | 9.307 1. | -| int 2 | 9.179 5.48 | 9.115 5. | 9.179 5. | 9.243 5. | 9.307 1. | -| int 2 | 9.307 5.48 | 9.115 5. | 9.179 5. | 9.243 5. | +9.307 5. | -| int 2 | 9.687 5.48 | 9.115 5. | 9.179 5. | 9.307 5. | 9.687 5. | -| int 2 | 9.495 5.48 | 9.115 5. | 9.179 5. | 9.307 5. | 9.495 5. | -| int 2 | 9.401 5.48 | 9.115 5. | 9.179 5. | 9.307 5. | 9.401 5. | -| final | 9.147 30.0 | 9.115 5. | 9.147 30 | 9.307 5. | 9.401 5. | -| final | 9.354 30.0 | 9.115 5. | 9.147 30 | 9.307 5. | 9.354 30 | -| final | 9.115 30.0 | +9.115 30 | 9.147 30 | 9.307 5. | 9.354 30 | -| final | 8.935 30.0 | 8.935 30 | 9.115 30 | 9.307 5. | 9.354 30 | -| final | 9.025 30.0 | 9.025 30 | 9.115 30 | 9.307 5. | 9.354 30 | -| final | 9.070 30.0 | 9.070 30 | 9.115 30 | 9.307 5. | 9.354 30 | -| final | 9.307 30.0 | 9.070 30 | 9.115 30 | 9.307 30 | 9.354 30 | - -# IANA Considerations - -No requests of IANA. - -# Security Considerations - -Benchmarking activities as described in this memo are limited to -technology characterization of a DUT/SUT using controlled stimuli in a -laboratory environment, with dedicated address space and the constraints -specified in the sections above. - -The benchmarking network topology will be an independent test setup and -MUST NOT be connected to devices that may forward the test traffic into -a production network or misroute traffic to the test management network. - -Further, benchmarking is performed on a "black-box" basis, relying -solely on measurements observable external to the DUT/SUT. - -Special capabilities SHOULD NOT exist in the DUT/SUT specifically for -benchmarking purposes. Any implications for network security arising -from the DUT/SUT SHOULD be identical in the lab and in production -networks. - -# Acknowledgements - -Many thanks to Alec Hothan of OPNFV NFVbench project for thorough -review and numerous useful comments and suggestions. - ---- back