X-Git-Url: https://gerrit.fd.io/r/gitweb?a=blobdiff_plain;f=doc%2Fguides%2Fnics%2Fixgbe.rst;fp=doc%2Fguides%2Fnics%2Fixgbe.rst;h=3dc6b004dff592786353c41e088ccf2238ece12d;hb=97f17497d162afdb82c8704bf097f0fee3724b2e;hp=0000000000000000000000000000000000000000;hpb=e04be89c2409570e0055b2cda60bd11395bb93b0;p=deb_dpdk.git diff --git a/doc/guides/nics/ixgbe.rst b/doc/guides/nics/ixgbe.rst new file mode 100644 index 00000000..3dc6b004 --- /dev/null +++ b/doc/guides/nics/ixgbe.rst @@ -0,0 +1,226 @@ +.. BSD LICENSE + Copyright(c) 2010-2014 Intel Corporation. All rights reserved. + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions + are met: + + * Redistributions of source code must retain the above copyright + notice, this list of conditions and the following disclaimer. + * Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in + the documentation and/or other materials provided with the + distribution. + * Neither the name of Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived + from this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + +IXGBE Driver +============ + +Vector PMD for IXGBE +-------------------- + +Vector PMD uses Intel® SIMD instructions to optimize packet I/O. +It improves load/store bandwidth efficiency of L1 data cache by using a wider SSE/AVX register 1 (1). +The wider register gives space to hold multiple packet buffers so as to save instruction number when processing bulk of packets. + +There is no change to PMD API. The RX/TX handler are the only two entries for vPMD packet I/O. +They are transparently registered at runtime RX/TX execution if all condition checks pass. + +1. To date, only an SSE version of IX GBE vPMD is available. + To ensure that vPMD is in the binary code, ensure that the option CONFIG_RTE_IXGBE_INC_VECTOR=y is in the configure file. + +Some constraints apply as pre-conditions for specific optimizations on bulk packet transfers. +The following sections explain RX and TX constraints in the vPMD. + +RX Constraints +~~~~~~~~~~~~~~ + +Prerequisites and Pre-conditions +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +The following prerequisites apply: + +* To enable vPMD to work for RX, bulk allocation for Rx must be allowed. + +Ensure that the following pre-conditions are satisfied: + +* rxq->rx_free_thresh >= RTE_PMD_IXGBE_RX_MAX_BURST + +* rxq->rx_free_thresh < rxq->nb_rx_desc + +* (rxq->nb_rx_desc % rxq->rx_free_thresh) == 0 + +* rxq->nb_rx_desc < (IXGBE_MAX_RING_DESC - RTE_PMD_IXGBE_RX_MAX_BURST) + +These conditions are checked in the code. + +Scattered packets are not supported in this mode. +If an incoming packet is greater than the maximum acceptable length of one "mbuf" data size (by default, the size is 2 KB), +vPMD for RX would be disabled. + +By default, IXGBE_MAX_RING_DESC is set to 4096 and RTE_PMD_IXGBE_RX_MAX_BURST is set to 32. + +Feature not Supported by RX Vector PMD +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Some features are not supported when trying to increase the throughput in vPMD. +They are: + +* IEEE1588 + +* FDIR + +* Header split + +* RX checksum off load + +Other features are supported using optional MACRO configuration. They include: + +* HW VLAN strip + +* HW extend dual VLAN + +* Enabled by RX_OLFLAGS (RTE_IXGBE_RX_OLFLAGS_ENABLE=y) + + +To guarantee the constraint, configuration flags in dev_conf.rxmode will be checked: + +* hw_vlan_strip + +* hw_vlan_extend + +* hw_ip_checksum + +* header_split + +* dev_conf + +fdir_conf->mode will also be checked. + +RX Burst Size +^^^^^^^^^^^^^ + +As vPMD is focused on high throughput, it assumes that the RX burst size is equal to or greater than 32 per burst. +It returns zero if using nb_pkt < 32 as the expected packet number in the receive handler. + +TX Constraint +~~~~~~~~~~~~~ + +Prerequisite +^^^^^^^^^^^^ + +The only prerequisite is related to tx_rs_thresh. +The tx_rs_thresh value must be greater than or equal to RTE_PMD_IXGBE_TX_MAX_BURST, +but less or equal to RTE_IXGBE_TX_MAX_FREE_BUF_SZ. +Consequently, by default the tx_rs_thresh value is in the range 32 to 64. + +Feature not Supported by RX Vector PMD +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +TX vPMD only works when txq_flags is set to IXGBE_SIMPLE_FLAGS. + +This means that it does not support TX multi-segment, VLAN offload and TX csum offload. +The following MACROs are used for these three features: + +* ETH_TXQ_FLAGS_NOMULTSEGS + +* ETH_TXQ_FLAGS_NOVLANOFFL + +* ETH_TXQ_FLAGS_NOXSUMSCTP + +* ETH_TXQ_FLAGS_NOXSUMUDP + +* ETH_TXQ_FLAGS_NOXSUMTCP + + +Sample Application Notes +~~~~~~~~~~~~~~~~~~~~~~~~ + +testpmd +^^^^^^^ + +By default, using CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=y: + +.. code-block:: console + + ./x86_64-native-linuxapp-gcc/app/testpmd -c 300 -n 4 -- -i --burst=32 --rxfreet=32 --mbcache=250 --txpt=32 --rxht=8 --rxwt=0 --txfreet=32 --txrst=32 --txqflags=0xf01 + +When CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=n, better performance can be achieved: + +.. code-block:: console + + ./x86_64-native-linuxapp-gcc/app/testpmd -c 300 -n 4 -- -i --burst=32 --rxfreet=32 --mbcache=250 --txpt=32 --rxht=8 --rxwt=0 --txfreet=32 --txrst=32 --txqflags=0xf01 --disable-hw-vlan + +l3fwd +^^^^^ + +When running l3fwd with vPMD, there is one thing to note. +In the configuration, ensure that port_conf.rxmode.hw_ip_checksum=0. +Otherwise, by default, RX vPMD is disabled. + +load_balancer +^^^^^^^^^^^^^ + +As in the case of l3fwd, set configure port_conf.rxmode.hw_ip_checksum=0 to enable vPMD. +In addition, for improved performance, use -bsz "(32,32),(64,64),(32,32)" in load_balancer to avoid using the default burst size of 144. + + +Malicious Driver Detection not Supported +---------------------------------------- + +The Intel x550 series NICs support a feature called MDD (Malicious +Driver Detection) which checks the behavior of the VF driver. +If this feature is enabled, the VF must use the advanced context descriptor +correctly and set the CC (Check Context) bit. +DPDK PF doesn't support MDD, but kernel PF does. We may hit problem in this +scenario kernel PF + DPDK VF. If user enables MDD in kernel PF, DPDK VF will +not work. Because kernel PF thinks the VF is malicious. But actually it's not. +The only reason is the VF doesn't act as MDD required. +There's significant performance impact to support MDD. DPDK should check if +the advanced context descriptor should be set and set it. And DPDK has to ask +the info about the header length from the upper layer, because parsing the +packet itself is not acceptable. So, it's too expensive to support MDD. +When using kernel PF + DPDK VF on x550, please make sure using the kernel +driver that disables MDD or can disable MDD. (Some kernel driver can use +this CLI 'insmod ixgbe.ko MDD=0,0' to disable MDD. Some kernel driver disables +it by default.) + + +Statistics +---------- + +The statistics of ixgbe hardware must be polled regularly in order for it to +remain consistent. Running a DPDK application without polling the statistics will +cause registers on hardware to count to the maximum value, and "stick" at +that value. + +In order to avoid statistic registers every reaching the maximum value, +read the statistics from the hardware using ``rte_eth_stats_get()`` or +``rte_eth_xstats_get()``. + +The maximum time between statistics polls that ensures consistent results can +be calculated as follows: + +.. code-block:: c + + max_read_interval = UINT_MAX / max_packets_per_second + max_read_interval = 4294967295 / 14880952 + max_read_interval = 288.6218096127183 (seconds) + max_read_interval = ~4 mins 48 sec. + +In order to ensure valid results, it is recommended to poll every 4 minutes.