X-Git-Url: https://gerrit.fd.io/r/gitweb?a=blobdiff_plain;f=src%2Fvnet%2Fbfd%2Fbfd_doc.md;h=7d7606e4dd18c5ba2cbf1290c73a13f9ee3dadca;hb=754f24b;hp=1333ed77b7e1ed056329cae96075dc558158ee69;hpb=7cd468a3d7dee7d6c92f69a0bb7061ae208ec727;p=vpp.git

diff --git a/src/vnet/bfd/bfd_doc.md b/src/vnet/bfd/bfd_doc.md
index 1333ed77b7e..7d7606e4dd1 100644
--- a/src/vnet/bfd/bfd_doc.md
+++ b/src/vnet/bfd/bfd_doc.md
@@ -1 +1,374 @@
-TODO
+# BFD module    {#bfd_doc}
+
+## Overview
+
+Bidirectional Forwarding Detection in VPP currently supports single-hop UDP
+transport based on RFC 5880 and RFC 5881.
+
+## Usage
+
+### General usage
+
+BFD sessions are created using APIs only. The following CLIs are implemented,
+which call the APIs to manipulate the BFD:
+
+#### Show commands:
+
+> show bfd [keys|sessions|echo-source]
+
+Show the existing keys, sessions or echo-source.
+
+#### Key manipulation
+
+##### Create a new key or modify an existing key
+
+> bfd key set conf-key-id <id> type <keyed-sha1|meticulous-keyed-sha1> secret <secret>
+
+Parameters:
+
+* conf-key-id     - local configuration key ID, used to uniquely identify this key
+* type            - type of the key
+* secret          - shared secret (hex data)
+
+Example:
+
+> bfd key set conf-key-id 2368880803 type meticulous-keyed-sha1 secret 69d685b0d990cdba46872706dc
+
+Notes:
+
+* in-use key cannot be modified
+
+##### Delete an existing key
+
+> bfd key del conf-key-id <id>
+
+Parameters:
+
+* conf-key-id     - local configuration key ID, used to uniquely identify this key
+
+Example:
+
+> bfd key del conf-key-id 2368880803
+
+Notes:
+
+*  in-use key cannot be deleted
+
+##### Create a new (plain or authenticated) BFD session
+
+> bfd udp session add interface <interface> local-addr <address> peer-addr <address> desired-min-tx <interval> required-min-rx <interval> detect-mult <multiplier> [ conf-key-id <ID> bfd-key-id <ID> ]
+
+Parameters:
+
+* interface       - interface to which this session is tied to
+* local-addr      - local address (ipv4 or ipv6)
+* peer-addr       - peer address (ipv4 or ipv6, must match local-addr family)
+* desired-min-tx  - desired minimum tx interval (microseconds)
+* required-min-rx - required minimum rx interval (microseconds)
+* detect-mult     - detect multiplier (must be non-zero)
+* conf-key-id     - local configuration key ID
+* bfd-key-id      - BFD key ID, as carried in BFD control frames
+
+Example:
+
+> bfd udp session add interface pg0 local-addr fd01:1::1 peer-addr fd01:1::2 desired-min-tx 100000 required-min-rx 100000 detect-mult 3 conf-key-id 1029559112 bfd-key-id 13
+
+Notes:
+
+* if conf-key-id and bfd-key-id are not specified, session is non-authenticated
+* desired-min-tx controls desired transmission rate of both control frames and echo packets
+
+##### Modify BFD session
+
+> bfd udp session mod interface <interface> local-addr <address> peer-addr <address> desired-min-tx <interval> required-min-rx <interval> detect-mult <multiplier>
+
+Parameters:
+
+* interface       - interface to which this session is tied to
+* local-addr      - local address (ipv4 or ipv6)
+* peer-addr       - peer address (ipv4 or ipv6, must match local-addr family)
+* desired-min-tx  - desired minimum tx interval (microseconds)
+* required-min-rx - required minimum rx interval (microseconds)
+* detect-mult     - detect multiplier (must be non-zero)
+
+Example:
+
+> bfd udp session mod interface pg0 local-addr 172.16.1.1 peer-addr 172.16.1.2 desired-min-tx 300000 required-min-rx 200000 detect-mult 12
+
+Notes:
+
+* desired-min-tx controls desired transmission rate of both control frames and echo packets
+
+##### Delete an existing BFD session
+
+> bfd udp session del interface <interface> local-addr <address> peer-addr<address>
+
+Parameters:
+
+* interface       - interface to which this session is tied to
+* local-addr      - local address (ipv4 or ipv6)
+* peer-addr       - peer address (ipv4 or ipv6, must match local-addr family)
+
+Example:
+
+> bfd udp session del interface pg0 local-addr 172.16.1.1 peer-addr 172.16.1.2
+
+##### Set session admin-up or admin-down
+
+> bfd udp session set-flags interface <interface> local-addr <address> peer-addr <address> admin <up|down>
+
+Parameters:
+
+* interface       - interface to which this session is tied to
+* local-addr      - local address (ipv4 or ipv6)
+* peer-addr       - peer address (ipv4 or ipv6, must match local-addr family)
+* admin           - up/down based on desired action
+
+Example:
+
+> bfd udp session set-flags admin down interface pg0 local-addr 172.16.1.1 peer-addr 172.16.1.2
+
+##### Activate/change authentication for existing session
+
+> bfd udp session auth activate interface <interface> local-addr <address> peer-addr <address> conf-key-id <ID> bfd-key-id <ID> [ delayed <yes|no> ]
+
+Parameters:
+
+* interface       - interface to which this session is tied to
+* local-addr      - local address (ipv4 or ipv6)
+* peer-addr       - peer address (ipv4 or ipv6, must match local-addr family)
+* conf-key-id     - local configuration key ID
+* bfd-key-id      - BFD key ID, as carried in BFD control frames
+* delayed         - is yes then this action is delayed until the peer performs the same action
+
+Example:
+
+> bfd udp session auth activate interface pg0 local-addr 172.16.1.1 peer-addr 172.16.1.2 conf-key-id 540928695 bfd-key-id 239 delayed yes
+
+Notes:
+
+* see [Delayed option] for more information
+
+##### Deactivate authentication for existing session
+
+> bfd udp session auth deactivate interface <interface> local-addr <address> peer-addr <address> [ delayed <yes|no> ]
+
+Parameters:
+
+* interface       - interface to which this session is tied to
+* local-addr      - local address (ipv4 or ipv6)
+* peer-addr       - peer address (ipv4 or ipv6, must match local-addr family)
+* delayed         - is yes then this action is delayed until the peer performs the same action
+
+Example:
+
+> bfd udp session auth deactivate interface pg0 local-addr 172.16.1.1 peer-addr 172.16.1.2
+
+Notes:
+
+* see [Delayed option] for more information
+
+##### Set echo-source interface
+
+> bfd udp echo-source set interface <interface>
+
+Parameters:
+
+* interface       - interface used for getting source address for echo packets
+
+Example:
+
+> bfd udp echo-source set interface loop0
+
+##### Delete echo-source interface
+
+> bfd udp echo-source del
+
+Example:
+
+> bfd udp echo-source del
+
+### Authentication
+
+BFD sessions should be authenticated for security purposes. SHA1 and meticulous
+SHA1 authentication is supported by VPP. First, authentication keys are
+configured in VPP and afterwards they can be used by sessions.
+
+There are two key IDs in the scope of BFD session:
+
+* configuration key ID is the internal unique key ID inside VPP and is never
+  communicated to any peer, it serves only the purpose of identifying the key
+* BFD key ID is the key ID carried in BFD control frames and is used for
+  verifying authentication
+
+#### Turning auth on/off
+
+Authentication can be turned on or off at any time. Care must be taken however,
+to either synchronize the authentication manipulation with peer's actions
+to avoid the session going down.
+
+##### Delayed option
+
+Delayed option is useful for synchronizing authentication changes with a peer.
+If it's specified, then authentication change is not performed immediately.
+In this case, VPP continues to transmit packets using the old authentication
+method (unauthenticated or using old sha1 key). If a packet is received, which
+does not pass the current authentication, then VPP tries to authenticate it
+using the new method (which might be none, if deactivating authentication)
+and if it passes, then the new authentication method is put in use.
+
+The recommended procedure for enabling/changing/disabling session 
+authentication is:
+
+1. perform authentication change on vpp's side with delayed option set to yes
+2. perform authentication change on peer's side (without delayed option)
+
+Notes:
+
+* if both peers use delayed option at the same time, the change will never
+  be carried out, since none of the peers will see any packet with the new
+  authentication which could trigger the change
+* remote peer does not need to support or even be aware of this mechanism
+  for it to work properly
+
+
+### Echo function
+
+Echo function is used by VPP whenever a peer declares the willingness
+to support it, echo-source is set and it contains a usable subnet (see below).
+When echo function is switched on, the required min rx interval advertised
+to peer is set to 1 second (or the configured value, if its higher).
+
+#### Echo source address
+
+Because echo packets are only looped back (and not processed in any way)
+by a peer, it's necessary to set the source address in a way which avoids
+packet drop due to spoofing protection by VPP. Per RFC, the source address
+should not be in the subnet set on the interface over which the echo packets
+are sent. Also, it must not be any VPP-local address, otherwise the packet
+gets dropped on receipt by VPP. The solution is to create a loopback interface
+with a (private) IPv4/IPv6 subnet assigned as echo-source. The BFD then picks
+an unused address from the subnet by flipping the last bit and uses that as
+source address in the echo packets, thus meeting RFC recommendation while
+avoiding spoofing protection.
+
+Example: if 10.10.10.3/31 is the subnet, then 10.10.10.2 will be used as
+         source address in (IPv4) echo packets
+
+### Demand mode
+
+Demand mode is respected by VPP, but not used locally. The only scenario when
+demand mode could make sense currently is when echo is active. Because echo
+packets are inherently insecure against an adversary looping them back a poll
+sequence would be required for slow periodic connectivity verification anyway.
+It's more efficient to just ask the remote peer to send slow periodic control
+frames without VPP initiating periodic poll sequences.
+
+### Admin-down
+
+Session may be put admin-down at any time. This immediately causes the state
+to be changed to AdminDown and remain so unless the session is put admin-up.
+
+## BFD implementation notes
+
+Because BFD can work over different transport layers, the BFD code is separated
+into core BFD functionality - main module implemented in bfd_main.c
+and transport-specific code implemented in bfd_udp.c.
+
+### Main module
+
+Main module is responsible for handling all the BFD functionality defined
+in RFC 5880.
+
+#### Internal API
+
+Internal APIs defined in bfd_main.h are called from transport-specific code
+to create/modify/delete
+
+#### Packet receipt
+
+When a packet is received by the transport layer, it is forwarded to main
+module (to main thread) via an RPC call. At this point, the authentication has
+been verified, so the packet is consumed, session parameters are updated
+accordingly and state change (if applicable). Based on these, the timeouts
+are adjusted if required and an event is sent to the process node to wake up
+and recalculate sleep time.
+
+#### Packet transmit
+
+Main module allocates a vlib_buffer_t, creates the required BFD frame (control
+or echo in it), then calls the transport layer to add the transport layer.
+Then a frame containing the buffer to the aprropriate node is created
+and enqueued.
+
+#### Process node
+
+Main module implements one process node which is a simple loop. The process
+node gets next timeout from the timer wheel, sleeps until the timeout expires
+and then calls a timeout routine which drives the state machine for each
+session which timed out. The sleep is interrupted externally via vlib event,
+when a session is added or modified in a way which might require timer wheel
+manipulation. In this case the caller inserts the necessary timeout to timer
+wheel and then signals the process node to wake up early, handle possible
+timeouts and recalculate the sleep time again.
+
+#### State machine
+
+Default state of BFD session when created is Down, per RFC 5880. State changes
+to Init, Up or Down based on events like received state from peer and timeouts.
+The session state can be set AdminDown using a binary API, which prevents it
+from going to any other state, until this limitation is removed. This state
+is advertised to peers in slow periodic control frames.
+
+For each session, the following timeouts are maintained:
+
+1. tx timeout - used for sending out control frames
+2. rx timeout - used for detecting session timeout
+3. echo tx timeout - used for sending out echo frames
+3. echo rx timeout - used for detecting session timeout based on echo
+
+These timeouts are maintained in cpu clocks and recalculated when appropriate
+(e.g. rx timeout is bumped when a packet is received, keeping the session
+alive). Only the earliest timeout is inserted into the timer wheel at a time
+and timer wheel events are never deleted, rather spurious events are ignored.
+This allows efficient operation, like not inserting events into timing wheel
+for each packet received or ignoring left-over events in case a bfd session
+gets removed and a new one is recreated with the same session index.
+
+#### Authentication keys management
+
+Authentication keys are managed internally in a pool, with each key tracking
+it's use count. The removal/modification is only allowed if the key is not in
+use.
+
+### UDP module
+
+UDP module is responsible for:
+
+1. public APIs/CLIs to configure BFD over UDP.
+2. support code called by main module to encapsulate/decapsulate BFD packets
+
+This module implements two graph nodes - for consuming ipv4 and ipv6 packets
+target at BFD ports 3874 and 3875.
+
+#### Packet receipt
+
+BFD packet receipt receipt starts in the bfd udp graph nodes. Since the code
+needs to verify IP/UDP header data, it relies on ip4-local (and ip6-local)
+nodes to store pointers to the appropriate headers. First, your discriminator
+is extracted from BFD packet and used to lookup the existing session. In case
+it's zero, the pair of IP addresses and sw_if_index is used to lookup session.
+Then, main module is called to verify the authentication, if present.
+Afterwards a check is made if the IP/UDP headers are correct. If yes, then
+an RPC call is made to the main thread to consume the packet and take action
+upon it.
+
+#### Packet transmission
+
+When process node decides that there is a need to transmit the packet, it
+creates a buffer, fills the BFD frame data in and calls the UDP module to
+add the transport layer. This is a simple operation for the control frames
+consisting of just adding UDP/IP headers based on session data. For echo
+frames, an additional step, looking at the echo-source interface and picking
+and address is performed and if this fails, then the packet cannot be
+transmitted and an error is returned to main thread.