X-Git-Url: https://gerrit.fd.io/r/gitweb?a=blobdiff_plain;f=tests%2Fperf%2F40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot;fp=tests%2Fperf%2F40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot;h=0000000000000000000000000000000000000000;hb=974897e8bcff8f3baeadf09b87840f530d8f41c1;hp=879bfa427be8c24a06fe385b7ad0c1c0b96b407f;hpb=81fc408c0dfcce0e093733810d80598abf25866a;p=csit.git

diff --git a/tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot b/tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot
deleted file mode 100644
index 879bfa427b..0000000000
--- a/tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot
+++ /dev/null
@@ -1,349 +0,0 @@
-# Copyright (c) 2017 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance.robot
-| Library | resources.libraries.python.NodePath
-| ...
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
-| ... | NIC_Cisco-VIC-1385 | ETH | L2BDMACLRN | BASE
-| ...
-| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
-| ... | L2 | Cisco-VIC-1385
-| Suite Teardown | 3-node Performance Suite Teardown
-| ...
-| Test Setup | Performance test setup
-| Test Teardown | Performance test teardown | ${min_rate}pps | ${framesize}
-| ... | 3-node-bridge
-| ...
-| Documentation | *RFC2544: Pkt throughput L2BD test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-
-| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p40GE NIC
-| ... | NIC_Cisco-VIC-1385.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using either binary search or linear search
-| ... | algorithms with configured starting rate and final step that determines
-| ... | throughput measurement resolution. Test packets are generated by TG on
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
-| ... | payload. MAC addresses are matching MAC addresses of the TG node
-| ... | interfaces.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-# XL710-DA2 (TG) bandwidth limit ~49Gbps/2=24.5Gbps
-| ${s_24.5G} | ${24500000000}
-# XL710-DA2 Mpps (TG) limit 37.5Mpps/2=18.75Mpps
-| ${s_18.75Mpps} | ${18750000}
-
-*** Test Cases ***
-| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\
-| | ... | 18.75Mpps rate, step 100kpps.
-| | ...
-| | [Tags] | 1T1C | STHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\
-| | ... | 18.75Mpps rate, step 100kpps.
-| | ...
-| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\
-| | ... | 24.5G rate, step 10kpps.
-| | ...
-| | [Tags] | 1T1C | STHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\
-| | ... | 24.5G rate, step 10kpps.
-| | ...
-| | [Tags] | 1T1C | STHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${9000}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\
-| | ... | 18.75Mpps rate, step 100kpps.
-| | ...
-| | [Tags] | 2T2C | MTHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\
-| | ... | 18.75Mpps rate, step 100kpps.
-| | ...
-| | [Tags] | 2T2C | MTHREAD | PDR | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\
-| | ... | 24.5G rate, step 10kpps.
-| | ...
-| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\
-| | ... | 18.75Mpps rate, step 100kpps.
-| | ...
-| | [Tags] | 4T4C | MTHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\
-| | ... | 24.5G rate, step 10kpps.
-| | ...
-| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
-| | And Add PCI devices to DUTs from 3-node single link topology
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc19-IMIX-1t1c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\
-| | ... | 24.5G rate, step 100kpps.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | 1T1C | STHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add all PCI devices to all DUTs
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc20-IMIX-2t2c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\
-| | ... | 24.5G rate, step 100kpps.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
-| | And Add all PCI devices to all DUTs
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}
-
-| tc21-IMIX-4t4c-eth-l2bdbasemaclrn-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 thread, 4 phy core,\
-| | ... | 2 receive queue per NIC port.
-| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\
-| | ... | 24.5G rate, step 100kpps.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${100000}
-| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
-| | And Add all PCI devices to all DUTs
-| | And Add No Multi Seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And L2 bridge domain initialized in a 3-node circular topology
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate}
-| | ... | ${threshold}