X-Git-Url: https://gerrit.fd.io/r/gitweb?a=blobdiff_plain;f=tests%2Fsuites%2Fperformance%2FLong_IPv6_Cop_Intel-X520-DA2.robot;h=e19fe619e62589f6b0f5f9bbfc683a962f067570;hb=5aa9925436c3ca40e9af9d353245674f631d440d;hp=e49566d7df713e7707c6fd6129656b39b9f4e228;hpb=55b4465a5c7ab8d8b340d67f1e11ba06a3ce39ea;p=csit.git diff --git a/tests/suites/performance/Long_IPv6_Cop_Intel-X520-DA2.robot b/tests/suites/performance/Long_IPv6_Cop_Intel-X520-DA2.robot index e49566d7df..e19fe619e6 100644 --- a/tests/suites/performance/Long_IPv6_Cop_Intel-X520-DA2.robot +++ b/tests/suites/performance/Long_IPv6_Cop_Intel-X520-DA2.robot @@ -20,30 +20,46 @@ | ... | L3 | Intel-X520-DA2 | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test -| Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | *Throughput search suite (based on RFC2544).* +| Test Teardown | Run Keywords | Remove startup configuration of VPP from all DUTs +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *RFC2544: Pkt throughput IPv6 whitelist test cases* | ... -| ... | Test suite uses 3-node topology TG - DUT1 - DUT2 - TG, with one link -| ... | between nodes. Traffic profile contain 2 L3 streams (1 stream per -| ... | direction). Packets contain Ethernet header, IPv6 header, and random -| ... | payload. Ethernet header MAC addresses are matching MAC addresses -| ... | of the TG node. COP (whitelist) is applied on link between TG - DUT1 -| ... | and DUT2 - TG. Additional ipv6 fib table with index 1 is created and -| ... | single entry added to permit all the traffic (subnet /64). +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist +| ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Test Cases *** -| Find NDR by using RFC2544 binary search and 78B frames through IPv6 forwarding with COP in 3-node topology +| TC01: 78B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate for 78B frames by using -| | ... | binary search with threshold 0.1Mpps. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_78B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -59,19 +75,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 78B frames through IPv6 forwarding with COP in 3-node topology +| TC02: 78B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate for 78B frames by using -| | ... | binary search with threshold 0.1Mpps. Loss acceptance is set to 0.5 -| | ... | percent of transmitted packets. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 78 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_78B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -89,18 +106,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR by using RFC2544 binary search and 1518B frames through IPv6 forwarding with COP in 3-node topology +| TC03: 1518B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate for 1518B frames by using -| | ... | binary search with threshold 10,000pps. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -116,19 +135,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 1518B frames through IPv6 forwarding with COP in 3-node topology +| TC04: 1518B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate for 1518B frames by using -| | ... | binary search with threshold 10,000pps. Loss acceptance is set to 0.5 -| | ... | percent of transmitted packets. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -146,18 +166,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR by using RFC2544 binary search and 9000B frames through IPv6 forwarding with COP in 3-node topology +| TC05: 9000B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate for 9000B frames by using -| | ... | binary search with threshold 5,000pps. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv6 forwarding initialized in a 3-node circular topology @@ -172,19 +194,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 9000B frames through IPv6 forwarding with COP in 3-node topology +| TC06: 9000B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate for 9000B frames by using -| | ... | binary search with threshold of 5,000pps. Loss acceptance is set to -| | ... | 0.5 percent of transmitted packets. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv6 forwarding initialized in a 3-node circular topology @@ -201,18 +224,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 78B frames through IPv6 forwarding with COP in 3-node topology +| TC07: 78B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate for 78B frames by using -| | ... | binary search with threshold 0.1Mpps. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_78B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -228,19 +253,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 78B frames through IPv6 forwarding with COP in 3-node topology +| TC08: 78B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate for 78B frames by -| | ... | using binary search with threshold 10,000pps. Loss acceptance is set -| | ... | to 0.5 percent of transmitted packets. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 78 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_78B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -258,18 +284,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 1518B frames through IPv6 forwarding with COP in 3-node topology +| TC09: 1518B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate for 1518B frames by -| | ... | using binary search with threshold 10,000pps. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -285,19 +313,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 1518B frames through IPv6 forwarding with COP in 3-node topology +| TC10: 1518B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate for 1518B frames by -| | ... | using binary search with threshold 10,000pps. Loss acceptance is set -| | ... | to 0.5 percent of transmitted packets. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -315,18 +344,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 9000B frames through IPv6 forwarding with COP in 3-node topology +| TC11: 9000B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate for 9000B frames by -| | ... | using binary search with threshold 5,000pps. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv6 forwarding initialized in a 3-node circular topology @@ -341,19 +372,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 9000B frames through IPv6 forwarding with COP in 3-node topology +| TC12: 9000B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate for 9000B frames by -| | ... | using binary search with threshold 5,000pps. Loss acceptance is set -| | ... | to 0.5 percent of transmitted packets. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv6 forwarding initialized in a 3-node circular topology @@ -370,18 +402,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 78B frames through IPv6 forwarding with COP in 3-node topology +| TC13: 78B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate for 78B -| | ... | frames by using binary search with threshold 0.1Mpps. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 78 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_78B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -397,19 +431,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 78B frames through IPv6 forwarding with COP in 3-node topology +| TC14: 78B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate for 78B -| | ... | frames by using binary search with threshold 0.1Mpps. Loss acceptance -| | ... | is set to 0.5 percent of transmitted packets. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 78 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_78B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -427,18 +462,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 1518B frames through IPv6 forwarding with COP in 3-node topology +| TC15: 1518B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate for 1518B -| | ... | frames by using binary search with threshold 10,000pps. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -454,19 +491,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 1518B frames through IPv6 forwarding with COP in 3-node topology +| TC16: 1518B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate for 1518B -| | ... | frames by using binary search with threshold 10,000pps. Loss -| | ... | acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -484,19 +522,20 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 9000B frames through IPv6 forwarding with COP in 3-node topology +| TC17: 9000B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate for 9000B -| | ... | frames by using binary search starting at 138,580pps, stepping down -| | ... | with step of 5,000pps. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv6 forwarding initialized in a 3-node circular topology @@ -511,19 +550,20 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 9000B frames through IPv6 forwarding with COP in 3-node topology +| TC18: 9000B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate for 9000B -| | ... | frames by using binary search with threshold 5,000pps. Loss -| | ... | acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv6 forwarding initialized in a 3-node circular topology