IPsectptLispGpe performance test suite

*[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
with single links between nodes.
*[Enc] Packet Encapsulations:* IPv4-IPSec-LISPGPE-IPv4.
*[Cfg] DUT configuration:* Each DUT is configured with LISP and IPsec.
IPsec is in transport mode. Tests cases are for IPsec configured both on
RLOC interface.

Change-Id: I7a95baf0305caac3d9f0702bbedb3feec27f1668
Signed-off-by: pmikus <pmikus@cisco.com>

diff --git a/resources/libraries/robot/performance.robot b/resources/libraries/robot/performance.robot
index ee66284..ccfc526 100644 (file)
--- a/resources/libraries/robot/performance.robot
+++ b/resources/libraries/robot/performance.robot
@@ -2140,16 +2140,56 @@
 | | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
 | | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
 | | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
 | | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
 | | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
 | | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}

-| | dut1_v4.set_arp | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
-| | dut1_v4.set_arp | ${dut1_if2} | ${dut2_dut1_address} | ${dut2_if1_mac}
-| | dut2_v4.set_arp | ${dut2_if1} | ${dut1_dut2_address} | ${dut1_if2_mac}
-| | dut2_v4.set_arp | ${dut2_if2} | 20.20.20.2 | ${tg1_if2_mac}
-| | dut1_v4.set_ip | ${dut1_if1} | ${dut1_tg_address} | ${duts_prefix}
-| | dut1_v4.set_ip | ${dut1_if2} | ${dut1_dut2_address} | ${duts_prefix}
-| | dut2_v4.set_ip | ${dut2_if1} | ${dut2_dut1_address} | ${duts_prefix}
-| | dut2_v4.set_ip | ${dut2_if2} | ${dut2_tg_address} | ${duts_prefix}
+| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
+| | Add arp on dut | ${dut1} | ${dut1_if2} | ${dut2_dut1_address}
+| | ... | ${dut2_if1_mac}
+| | Add arp on dut | ${dut2} | ${dut2_if1} | ${dut1_dut2_address}
+| | ... | ${dut1_if2_mac}
+| | Add arp on dut | ${dut2} | ${dut2_if2} | 20.20.20.2 | ${tg1_if2_mac}
+| | IP addresses are set on interfaces | ${dut1} | ${dut1_if1}
+| | ... | ${dut1_tg_address} | ${duts_prefix}
+| | IP addresses are set on interfaces | ${dut1} | ${dut1_if2}
+| | ... | ${dut1_dut2_address} | ${duts_prefix}
+| | IP addresses are set on interfaces | ${dut2} | ${dut2_if1}
+| | ... | ${dut2_dut1_address} | ${duts_prefix}
+| | IP addresses are set on interfaces | ${dut2} | ${dut2_if2}
+| | ... | ${dut2_tg_address} | ${duts_prefix}

 | | All Vpp Interfaces Ready Wait | ${nodes}
 
 | | All Vpp Interfaces Ready Wait | ${nodes}
 

+| Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | [Documentation] | Setup Lisp GPE IPv4 forwarding over IPsec.
+| | ...
+| | ... | *Arguments:*
+| | ... | -${encr_alg} - Encryption algorithm. Type: string
+| | ... | -${auth_alg} - Authentication algorithm. Type: string
+| | ...
+| | ... | *Return:*
+| | ... | - No value returned
+| | ...
+| | ... | *Example:*
+| | ... | \| Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology\
+| | ... | \| ${encr_alg} \| ${auth_alg}
+| | ...
+| | [Arguments] | ${encr_alg} | ${auth_alg}
+| | ...
+| | IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | Set up LISP GPE topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | VPP Setup IPsec Manual Keyed Connection
+| | ... | ${dut1} | ${dut1_if2} | ${encr_alg} | ${encr_key}
+| | ... | ${auth_alg} | ${auth_key} | ${dut1_spi} | ${dut2_spi}
+| | ... | ${dut1_to_dut2_ip4} | ${dut2_to_dut1_ip4}
+| | VPP Setup IPsec Manual Keyed Connection
+| | ... | ${dut2} | ${dut2_if1} | ${encr_alg} | ${encr_key}
+| | ... | ${auth_alg} | ${auth_key} | ${dut2_spi} | ${dut1_spi}
+| | ... | ${dut2_to_dut1_ip4} | ${dut1_to_dut2_ip4}
+

 | Lisp IPv6 forwarding initialized in a 3-node circular topology
 | | [Documentation] | Custom setup of IPv6 topology on all DUT nodes \
 | | ... | Don`t set route.
 | Lisp IPv6 forwarding initialized in a 3-node circular topology
 | | [Documentation] | Custom setup of IPv6 topology on all DUT nodes \
 | | ... | Don`t set route.


@@ -2227,15 +2267,17 @@
 | | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
 | | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
 | | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
 | | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
 | | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
 | | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}

-| | dut1_v4.set_ip | ${dut1_if1} | ${dut1_tg_ip4_address} | ${prefix4}
+| | IP addresses are set on interfaces | ${dut1} | ${dut1_if1}
+| | ... | ${dut1_tg_ip4_address} | ${prefix4}

 | | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | ${dut1_dut2_ip6_address}
 | | ... | ${prefix6}
 | | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | ${dut2_dut1_ip6_address}
 | | ... | ${prefix6}
 | | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | ${dut1_dut2_ip6_address}
 | | ... | ${prefix6}
 | | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | ${dut2_dut1_ip6_address}
 | | ... | ${prefix6}

-| | dut2_v4.set_ip | ${dut2_if2} | ${dut2_tg_ip4_address} | ${prefix4}
+| | IP addresses are set on interfaces | ${dut2} | ${dut2_if2}
+| | ... | ${dut2_tg_ip4_address} | ${prefix4}

 | | Vpp nodes ra suppress link layer | ${nodes}
 | | Vpp nodes ra suppress link layer | ${nodes}

-| | dut1_v4.set_arp | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
-| | dut2_v4.set_arp | ${dut2_if2} | 20.20.20.2 | ${tg1_if2_mac}
+| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
+| | Add arp on dut | ${dut2} | ${dut2_if2} | 20.20.20.2 | ${tg1_if2_mac}

 | | Add Ip Neighbor | ${dut1} | ${dut1_if2} | ${dut2_dut1_ip6_address}
 | | ... | ${dut2_if1_mac}
 | | Add Ip Neighbor | ${dut2} | ${dut2_if1} | ${dut1_dut2_ip6_address}
 | | Add Ip Neighbor | ${dut1} | ${dut1_if2} | ${dut2_dut1_ip6_address}
 | | ... | ${dut2_if1_mac}
 | | Add Ip Neighbor | ${dut2} | ${dut2_if1} | ${dut1_dut2_ip6_address}


@@ -2278,15 +2320,19 @@
 | | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
 | | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | ${dut1_tg_ip6_address}
 | | ... | ${prefix6}
 | | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
 | | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | ${dut1_tg_ip6_address}
 | | ... | ${prefix6}

-| | dut1_v4.set_ip | ${dut1_if2} | ${dut1_dut2_ip4_address} | ${prefix4}
-| | dut2_v4.set_ip | ${dut2_if1} | ${dut2_dut1_ip4_address} | ${prefix4}
+| | IP addresses are set on interfaces | ${dut1} | ${dut1_if2}
+| | ... | ${dut1_dut2_ip4_address} | ${prefix4}
+| | IP addresses are set on interfaces | ${dut2} | ${dut2_if1}
+| | ... | ${dut2_dut1_ip4_address} | ${prefix4}

 | | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if2} | ${dut2_tg_ip6_address}
 | | ... | ${prefix6}
 | | Vpp nodes ra suppress link layer | ${nodes}
 | | Add Ip Neighbor | ${dut1} | ${dut1_if1} | 2001:1::2 | ${tg1_if1_mac}
 | | Add Ip Neighbor | ${dut2} | ${dut2_if2} | 2001:2::2 | ${tg1_if2_mac}
 | | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if2} | ${dut2_tg_ip6_address}
 | | ... | ${prefix6}
 | | Vpp nodes ra suppress link layer | ${nodes}
 | | Add Ip Neighbor | ${dut1} | ${dut1_if1} | 2001:1::2 | ${tg1_if1_mac}
 | | Add Ip Neighbor | ${dut2} | ${dut2_if2} | 2001:2::2 | ${tg1_if2_mac}

-| | dut1_v4.set_arp | ${dut1_if2} | ${dut2_dut1_ip4_address} | ${dut2_if1_mac}
-| | dut2_v4.set_arp | ${dut2_if1} | ${dut1_dut2_ip4_address} | ${dut1_if2_mac}
+| | Add arp on dut | ${dut1} | ${dut1_if2} | ${dut2_dut1_ip4_address}
+| | ... | ${dut2_if1_mac}
+| | Add arp on dut | ${dut2} | ${dut2_if1} | ${dut1_dut2_ip4_address}
+| | ... | ${dut1_if2_mac}

 
 | DPDK 2-node Performance Suite Setup with DUT's NIC model
 | | [Documentation]
 
 | DPDK 2-node Performance Suite Setup with DUT's NIC model
 | | [Documentation]

diff --git a/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrchk.robot b/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrchk.robot
index f31dbde..d54557c 100644 (file)
--- a/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrchk.robot
+++ b/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrchk.robot
@@ -14,10 +14,6 @@
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot

-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
-| ... | WITH NAME | dut1_v4
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
-| ... | WITH NAME | dut2_v4

 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK
 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK

diff --git a/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrpdrdisc.robot b/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrpdrdisc.robot
index 8c676db..42d607d 100644 (file)
--- a/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrpdrdisc.robot
+++ b/tests/perf/10ge2p1x520-ethip4lispip4-ip4base-ndrpdrdisc.robot
@@ -14,10 +14,6 @@
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot

-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
-| ... | WITH NAME | dut1_v4
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
-| ... | WITH NAME | dut2_v4

 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC

diff --git a/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrchk.robot b/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrchk.robot
index 1c9cb0e..e3771a0 100644 (file)
--- a/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrchk.robot
+++ b/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrchk.robot
@@ -14,10 +14,6 @@
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot

-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
-| ... | WITH NAME | dut1_v4
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
-| ... | WITH NAME | dut2_v4

 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK
 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK

diff --git a/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot b/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot
index d49ae42..37415eb 100644 (file)
--- a/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot
+++ b/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot
@@ -14,10 +14,6 @@
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot

-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
-| ... | WITH NAME | dut1_v4
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
-| ... | WITH NAME | dut2_v4

 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC

diff --git a/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrchk.robot b/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrchk.robot
index 8debdef..c71badc 100644 (file)
--- a/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrchk.robot
+++ b/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrchk.robot
@@ -14,10 +14,6 @@
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot

-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
-| ... | WITH NAME | dut1_v4
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
-| ... | WITH NAME | dut2_v4

 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK
 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK

diff --git a/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrpdrdisc.robot b/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrpdrdisc.robot
index dbd7f7b..c8283ab 100644 (file)
--- a/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrpdrdisc.robot
+++ b/tests/perf/10ge2p1x520-ethip6lispip4-ip6base-ndrpdrdisc.robot
@@ -14,10 +14,6 @@
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot
 *** Settings ***
 | Resource | resources/libraries/robot/performance.robot
 | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot

-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
-| ... | WITH NAME | dut1_v4
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
-| ... | WITH NAME | dut2_v4

 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
 | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
 | ...
 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC

diff --git a/tests/perf/40ge2p1xl710-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc.robot b/tests/perf/40ge2p1xl710-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc.robot
new file mode 100644 (file)
index 0000000..55b7599
--- /dev/null
+++ b/tests/perf/40ge2p1xl710-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc.robot
@@ -0,0 +1,363 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Resource | resources/libraries/robot/ipsec.robot
+| Resource | resources/libraries/robot/lisp/lispgpe.robot
+| ...
+| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC | IP4FWD
+| ... | LISPGPE | IPSEC | IPSECHW | IPSECTRAN | ENCAP | IP4UNRLAY | IP4OVRLAY
+| ... | NIC_Intel-XL710
+| ...
+| Suite Setup | Run Keywords
+| ... | 3-node Performance Suite Setup with DUT's NIC model | L3 | Intel-XL710
+| ... | AND | Verify Crypto Device On All DUTs | force_init=${True}
+| ... | AND | Verify Kernel Module On All DUTs | igb_uio | force_load=${True}
+| Suite Teardown | 3-node Performance Suite Teardown
+| ...
+| Test Setup | Performance test setup
+| Test Teardown | Performance test teardown | ${min_rate}pps | ${framesize}
+| ... | 3-node-IPv4
+| ...
+| Documentation | *IPv4 IPsec transport mode performance test suite.*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn,\
+| ... | Eth-IPv4-IPSec-LISPGPE-IPv4 on DUT1-DUT2
+| ... | *[Cfg] DUT configuration:* Each DUT is configured with LISP and IPsec\
+| ... | in each direction. IPsec is in transport mode. DUTs get IPv4 traffic\
+| ... | from TG, encrypt it and send to another DUT, where packets are\
+| ... | decrypted and sent back to TG.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in number\
+| ... | of packets transmitted. NDR is discovered for different\
+| ... | number of IPsec tunnels using binary search algorithms with configured\
+| ... | starting rate and final step that determines throughput measurement\
+| ... | resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, number of flows per flow-group equals to\
+| ... | number of IPSec tunnels) with all packets\
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and\
+| ... | static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces. Incrementing of IP.dst (IPv4 destination address)\
+| ... | field is applied to both streams.
+| ... | *[Ref] Applicable standard specifications:* RFC6830, RFC4303 and\
+| ... | RFC2544.
+
+*** Variables ***
+# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+| ${dut2_spi}= | ${1000}
+| ${dut1_spi}= | ${1001}
+| ${ESP_PROTO}= | ${50}
+| ${ipsec_overhead}= | ${54}
+
+*** Test Cases ***
+| tc01-64B-1t1c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Add Cryptodev to all DUTs | ${1}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc02-64B-1t1c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Add Cryptodev to all DUTs | ${1}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc03-1518B-1t1c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize + ${ipsec_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add Cryptodev to all DUTs | ${1}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc04-1518B-1t1c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize + ${ipsec_overhead}}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add Cryptodev to all DUTs | ${1}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc05-IMIX-1t1c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${imix_size}= | Get Frame Size | ${framesize}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${imix_size} + ${ipsec_overhead}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add Cryptodev to all DUTs | ${1}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc06-IMIX-1t1c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 1 thread, 1 phy\
+| | ... | core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for IMIX_v4_1 frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | IMIX_v4_1
+| | ${imix_size}= | Get Frame Size | ${framesize}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${imix_size} + ${ipsec_overhead}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add Cryptodev to all DUTs | ${1}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc07-64B-2t2c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Add Cryptodev to all DUTs | ${2}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc08-64B-2t2c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 2 threads, 2 phy\
+| | ... | cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Add Cryptodev to all DUTs | ${2}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc13-64B-4t4c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 4 threads, 4 phy\
+| | ... | cores, 2 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Add Cryptodev to all DUTs | ${4}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc14-64B-4t4c-ethip4ipsectptlispgpe-ip4base-cbc-sha1-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] Each DUT is configured with LISP and IPsec in each direction.\
+| | ... | IPsec is in transport mode. DUTs are configured with 4 threads, 4 phy\
+| | ... | cores, 2 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 40GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Set Variable | ${s_18.75Mpps}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Add Cryptodev to all DUTs | ${4}
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp GPE IPv4 over IPsec initialized in a 3-node circular topology
+| | ... | ${encr_alg} | ${auth_alg}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4 | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}