Update vagrant/ to install vpp packages and use vppctl 84/84/1
authorEd Warnicke <eaw@cisco.com>
Wed, 23 Dec 2015 03:04:54 +0000 (20:04 -0700)
committerEd Warnicke <eaw@cisco.com>
Wed, 23 Dec 2015 03:04:54 +0000 (20:04 -0700)
Change-Id: I30f0cb52152bed174fa82a09fb8584c193df4d2c
Signed-off-by: Ed Warnicke <eaw@cisco.com>
build-root/vagrant/README
build-root/vagrant/bootstrap.ubuntu1404.sh

index 0498615..05a3c65 100644 (file)
@@ -1,43 +1,50 @@
-To run vpp with the debug shell:
+VPP has now been built, installed, and started.
 
-sudo ~vagrant/git/vpp/build-root/install-vpp_debug-native/vpp/bin/vpe unix interactive
+To give it a spin, we can create a tap interface and try a simple ping
+(with trace).
 
-which will result in a prompt that looks like:
+Make sure you have run:
 
-DBGvpd#
+$ vagrant ssh
 
-To give it a spin, we can create a tap interface and try a simple ping
-(with trace).
+To get to the vagrant VM:
+
+vagrant@localhost:~$
+
+Confirm that vpp is running with
+
+vagrant@localhost:~$ sudo status vpp
+vpp start/running, process 25202
 
 To create the tap:
 
-DBGvpd# tap connect foobar
+vagrant@localhost:~$ sudo vppctl tap connect foobar
 Created tap-0 for Linux tap 'foobar'
-DBGvpd# show int
+vagrant@localhost:~$ sudo vppctl show int
 
 To assign it an ip address (and 'up' the interface):
 
-DBGvpd# set int ip address tap-0 192.168.1.1/24
-DBGvpd# set int state tap-0 up
+vagrant@localhost:~$ sudo vppctl set int ip address tap-0 192.168.1.1/24
+vagrant@localhost:~$ sudo vppctl set int state tap-0 up
 
 To turn on packet tracing for the tap interface:
-DBGvpd# trace add tapcli-rx 10
+vagrant@localhost:~$ sudo vppctl trace add tapcli-rx 10
 
-Now, to set up and try the other end from the unix prompt:
-vagrant@vagrant-ubuntu-trusty-64:~$ sudo ip addr add 192.168.1.2/24 dev foobar
-vagrant@vagrant-ubuntu-trusty-64:~$ ping -c 3 192.168.1.1
+Now, to set up and try the other end:
+vagrant@localhost:~$ sudo ip addr add 192.168.1.2/24 dev foobar
+vagrant@localhost:~$ ping -c 3 192.168.1.1
 
-To look at the trace, back in the vpp CLI:
-DBGvpd#  show trace
+To look at the trace:
+vagrant@localhost:~$ sudo vppctl show trace
 
 And to stop tracing:
 
-DBGvpd# clear trace
+vagrant@localhost:~$ sudo vppctl clear trace
 
 Other fun things to look at:
 
 The vlib packet processing graph:
-DBGvpd# show vlib graph
+vagrant@localhost:~$ sudo vppctl show vlib graph
 
 which will produce output like:
 
index c89f098..89cd4e8 100644 (file)
@@ -61,16 +61,12 @@ if [ -d build-root ]; then
   # Build vpp
   sudo -H -u vagrant make PLATFORM=vpp TAG=vpp_debug install-deb
 
-  # Stick the dpdk module in the canonical place
-  cp ./install-vpp_debug-native/dpdk/kmod/igb_uio.ko /lib/modules/`uname -r`/kernel/drivers/uio/
-  depmod
+  # Install debian packages
+  dpkg -i *.deb
 
-  # Load igb_uio into the kernel
-  modprobe igb_uio
+  # Start vpp
+  start vpp
 
-  # Make sure igb_uio loads at boot time
-  # Make sure uio loads at boot time
-  echo  igb_uio >> /lib/modprobe.d/igb_uio.conf
   cd ~vagrant/
   cat /vagrant/README