Remove leading tc[nn] from test names
[csit.git] / tests / vpp / device / ip4_tunnels / lisp / eth2p-ethip4lispgpe-ip6base-dev.robot
1 # Copyright (c) 2020 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/shared/default.robot
16 |
17 | Variables | resources/test_data/lisp/lisp.py
18 |
19 | Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY
20 | ... | NIC_Virtual | IP4FWD | LISP | LISPGPE_IP6o4 | DRV_VFIO_PCI
21 | ... | RXQ_SIZE_0 | TXQ_SIZE_0
22 | ... | ethip4lispgpe-ip6base
23 |
24 | Suite Setup | Setup suite topology interfaces | scapy
25 | Test Setup | Setup test
26 | Test Teardown | Tear down test | packet_trace
27 |
28 | Test Template | Local Template
29 |
30 | Documentation | *ip4-lispgpe-ip6 encapsulation test cases*
31 |
32 | ... | *[Top] Network Topologies:* TG(if1)-DUT1-TG(if2) 2-node\
33 | ... | circular topology with single links between nodes.
34 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISPGPE-IPv6-ICMPv6\
35 | ... | on DUT1-TG(if2),Eth-IPv6-ICMPv6 on TG-DUTn for IPv6\
36 | ... | routing over LISPoIPv4 tunnel.
37 | ... | *[Cfg] DUT configuration:* DUT1 and TG(if2) are configured\
38 | ... | with IPv6 routing and static routes. LISPoIPv4 tunnel is\
39 | ... | configured between DUT1 and TG(if2).
40 | ... | *[Ver] TG verification:* Test ICMPv6 Echo Request packets\
41 | ... | are sent in if1 by TG on links to DUT1; on receive\
42 | ... | TG verifies packets for correctness and their IPv6 src-addr,\
43 | ... | dst-addr and MAC addresses.
44 | ... | *[Ref] Applicable standard specifications:* RFC6830.
45
46 *** Variables ***
47 | @{plugins_to_enable}= | dpdk_plugin.so
48 | ${crypto_type}= | ${None}
49 | ${nic_name}= | virtual
50 | ${nic_driver}= | vfio-pci
51 | ${nic_rxq_size}= | 0
52 | ${nic_txq_size}= | 0
53 | ${nic_pfs}= | 2
54 | ${nic_vfs}= | 0
55 | ${overhead}= | ${54}
56 | ${ot_mode}= | 6to4
57 | ${is_gpe}= | ${1}
58
59 *** Keywords ***
60 | Local Template
61 | | [Documentation]
62 | | ... | [Cfg] On DUT1 configure LISPGPE\
63 | |
64 | | ... | *Arguments:*
65 | | ... | - frame_size - Framesize in Bytes in integer. Type: integer
66 | | ... | - phy_cores - Number of physical cores. Type: integer
67 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
68 | |
69 | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
70 | |
71 | | Set Test Variable | \${frame_size}
72 | |
73 | | Given Set Max Rate And Jumbo
74 | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
75 | | And Pre-initialize layer driver | ${nic_driver}
76 | | And Apply startup configuration on all VPP DUTs | with_trace=${True}
77 | | When Initialize layer driver | ${nic_driver}
78 | | And Initialize layer interface
79 | | And Configure topology for IPv6 LISPoIP4 testing
80 | | And Vpp All RA Suppress Link Layer | ${nodes}
81 | | And Configure LISP in 2-node circular topology
82 | | ... | ${dut1} | ${DUT1_${int}2}[0] | ${NONE}
83 | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid}
84 | | ... | ${dut1_ip6o4_static_adjacency} | ${is_gpe}
85 | | Then Send packet and verify LISPoTunnel encap
86 | | ... | ${tg} | ${tg_if1_ip6} | ${dst_ip6}
87 | | ... | ${TG_pf1}[0] | ${TG_pf1_mac}[0] | ${DUT1_vf1_mac}[0]
88 | | ... | ${TG_pf2}[0] | ${DUT1_vf2_mac}[0] | ${TG_pf2_mac}[0]
89 | | ... | ${src_rloc4} | ${dst_rloc4} | ${ot_mode}
90
91 *** Test Cases ***
92 | 62B-ethip4lispgpe-ip6base-dev
93 | | [Tags] | 62B
94 | | frame_size=${62} | phy_cores=${0}