[csit.git] / tests / vpp / perf / container_memif / 2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot

# Copyright (c) 2018 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.

*** Settings ***
| Resource | resources/libraries/robot/performance/performance_setup.robot
| ...
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
| ... | NIC_Intel-XXV710 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER
| ...
| Suite Setup | Run Keywords
| ... | Set up 2-node performance topology with DUT's NIC model | L2
| ... | Intel-XXV710
| ... | AND | Set up performance test suite with MEMIF
| ... | AND | Set up performance topology with containers
| ...
| Suite Teardown | Tear down 2-node performance topology with container
| ...
| Test Setup | Run Keywords
| ... | Set up performance test
| ... | AND | Restart VPP in all 'VNF' containers
| ...
| Test Teardown | Tear down performance mrr test
| ...
| Test Template | Local Template
| ...
| Documentation | *Raw results L2BD with memif and IEEE 802.1Q test cases*
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
| ... | single links between nodes.
| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\
| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
| ... | *[Cfg] DUT configuration:* DUT1 is configured with two L2 bridge\
| ... | domains and MAC learning enabled. Container is connected to VPP via\
| ... | Memif interface. Container is running same VPP version as running\
| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\
| ... | pool of isolated CPUs. There are no memory constraints. DUT1 is tested\
| ... | with 2p25GE NIC XXV710 by Intel.
| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
| ... | at line rate and reports total received/sent packets over trial period.\
| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
| ... | addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.

*** Variables ***
| ${subid}= | 10
| ${tag_rewrite}= | pop-1
| ${bd_id1}= | 1
| ${bd_id2}= | 2
| ${overhead}= | ${4}
# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
| ${s_24.5G}= | ${24500000000}
# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
| ${s_18.75Mpps}= | ${18750000}
# Traffic profile:
| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
# LXC container
| ${container_count}= | ${1}
| ${container_engine}= | Docker
| ${container_image}= | ubuntu:xenial-20180412
| ${container_install_dkms}= | ${FALSE}
| ${container_chain_topology}= | chain
# CPU settings
| ${system_cpus}= | ${1}
| ${vpp_cpus}= | ${5}
| ${container_cpus}= | ${5}

*** Keywords ***
| Local Template
| | [Documentation]
| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\
| | ... | physical core(s) for worker threads.
| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
| | ... | trial throughput test.
| | ...
| | ... | *Arguments:*
| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
| | ... | Type: integer, string
| | ... | - phy_cores - Number of physical cores. Type: integer
| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
| | ...
| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
| | ...
| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
| | And Add PCI devices to all DUTs
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
| | ... | overhead=${overhead}
| | And Apply startup configuration on all VPP DUTs
| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology
| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}

*** Test Cases ***
| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 64B | 1C
| | framesize=${64} | phy_cores=${1}

| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 64B | 2C
| | framesize=${64} | phy_cores=${2}

| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 64B | 4C
| | framesize=${64} | phy_cores=${4}

| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 1518B | 1C
| | framesize=${1518} | phy_cores=${1}

| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 1518B | 2C
| | framesize=${1518} | phy_cores=${2}

| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 1518B | 4C
| | framesize=${1518} | phy_cores=${4}

| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 9000B | 1C
| | framesize=${9000} | phy_cores=${1}

| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 9000B | 2C
| | framesize=${9000} | phy_cores=${2}

| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | 9000B | 4C
| | framesize=${9000} | phy_cores=${4}

| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | IMIX | 1C
| | framesize=IMIX_v4_1 | phy_cores=${1}

| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | IMIX | 2C
| | framesize=IMIX_v4_1 | phy_cores=${2}

| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr
| | [Tags] | IMIX | 4C
| | framesize=IMIX_v4_1 | phy_cores=${4}