Support suite tags in autogen
[csit.git] / tests / vpp / perf / ip4 / 10ge2p1x710-ethip4-ip4base-copwhtlistbase-ndrpdr.robot
1 # Copyright (c) 2019 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/shared/default.robot
16 |
17 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
18 | ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | COPWHLIST | DRV_VFIO_PCI
19 | ... | ethip4-ip4base-copwhtlistbase
20 |
21 | Suite Setup | Setup suite single link | performance
22 | Suite Teardown | Tear down suite | performance
23 | Test Setup | Setup test
24 | Test Teardown | Tear down test | performance
25 |
26 | Test Template | Local Template
27 |
28 | Documentation | *RFC2544: Pkt throughput IPv4 whitelist test cases*
29 |
30 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
31 | ... | with single links between nodes.
32 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
33 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
34 | ... | routing, two static IPv4 /24 routes and IPv4 COP security whitelist
35 | ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
36 | ... | DUT1 and DUT2 tested with ${nic_name}.\
37 | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
38 | ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\
39 | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
40 | ... | of packets transmitted. NDR and PDR are discovered for different\
41 | ... | Ethernet L2 frame sizes using MLRsearch library.\
42 | ... | Test packets are generated by TG on links to DUTs. TG traffic profile
43 | ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
44 | ... | flow-group) with all packets containing Ethernet header, IPv4 header
45 | ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
46 | ... | addresses of the TG node interfaces.
47 | ... | *[Ref] Applicable standard specifications:* RFC2544.
48
49 *** Variables ***
50 | @{plugins_to_enable}= | dpdk_plugin.so
51 | ${crypto_type}= | ${None}
52 | ${nic_name}= | Intel-X710
53 | ${nic_driver}= | vfio-pci
54 | ${osi_layer}= | L3
55 | ${overhead}= | ${0}
56 # Traffic profile:
57 | ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
58
59 *** Keywords ***
60 | Local Template
61 | | [Documentation]
62 | | ... | [Cfg] DUT runs IPv4 routing config. \
63 | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
64 | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
65 | |
66 | | ... | *Arguments:*
67 | | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1).
68 | | ... | Type: integer, string
69 | | ... | - phy_cores - Number of physical cores. Type: integer
70 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
71 | |
72 | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
73 | |
74 | | Set Test Variable | \${frame_size}
75 | |
76 | | Given Set Max Rate And Jumbo
77 | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
78 | | And Pre-initialize layer driver | ${nic_driver}
79 | | And Apply startup configuration on all VPP DUTs
80 | | When Initialize layer driver | ${nic_driver}
81 | | And Initialize layer interface
82 | | And Initialize IPv4 forwarding in circular topology
83 | | And Add Fib Table | ${dut1} | 1
84 | | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=1 | local=${TRUE}
85 | | And Add Fib Table | ${dut2} | 1
86 | | And Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | vrf=1 | local=${TRUE}
87 | | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip4 | 1
88 | | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip4 | 1
89 | | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
90 | | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
91 | | Then Find NDR and PDR intervals using optimized search
92
93 *** Test Cases ***
94 | tc01-64B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
95 | | [Tags] | 64B | 1C
96 | | frame_size=${64} | phy_cores=${1}
97
98 | tc02-64B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
99 | | [Tags] | 64B | 2C
100 | | frame_size=${64} | phy_cores=${2}
101
102 | tc03-64B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
103 | | [Tags] | 64B | 4C
104 | | frame_size=${64} | phy_cores=${4}
105
106 | tc04-1518B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
107 | | [Tags] | 1518B | 1C
108 | | frame_size=${1518} | phy_cores=${1}
109
110 | tc05-1518B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
111 | | [Tags] | 1518B | 2C
112 | | frame_size=${1518} | phy_cores=${2}
113
114 | tc06-1518B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
115 | | [Tags] | 1518B | 4C
116 | | frame_size=${1518} | phy_cores=${4}
117
118 | tc07-9000B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
119 | | [Tags] | 9000B | 1C
120 | | frame_size=${9000} | phy_cores=${1}
121
122 | tc08-9000B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
123 | | [Tags] | 9000B | 2C
124 | | frame_size=${9000} | phy_cores=${2}
125
126 | tc09-9000B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
127 | | [Tags] | 9000B | 4C
128 | | frame_size=${9000} | phy_cores=${4}
129
130 | tc10-IMIX-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
131 | | [Tags] | IMIX | 1C
132 | | frame_size=IMIX_v4_1 | phy_cores=${1}
133
134 | tc11-IMIX-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
135 | | [Tags] | IMIX | 2C
136 | | frame_size=IMIX_v4_1 | phy_cores=${2}
137
138 | tc12-IMIX-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
139 | | [Tags] | IMIX | 4C
140 | | frame_size=IMIX_v4_1 | phy_cores=${4}