Align suite/test teardown/setup
[csit.git] / tests / vpp / perf / ip4 / 10ge2p1x710-ethip4-ip4base-copwhtlistbase-ndrpdr.robot
1 # Copyright (c) 2019 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/shared/default.robot
16 | Library | resources.libraries.python.Cop
17 | ...
18 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
19 | ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | COPWHLIST
20 | ...
21 | Suite Setup | Setup suite single link | performance
22 | Suite Teardown | Tear down suite | performance
23 | Test Setup | Setup test
24 | Test Teardown | Tear down test | performance
25 | ...
26 | Test Template | Local Template
27 | ...
28 | Documentation | *RFC2544: Pkt throughput IPv4 whitelist test cases*
29 | ...
30 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
31 | ... | with single links between nodes.
32 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
33 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
34 | ... | routing, two static IPv4 /24 routes and IPv4 COP security whitelist
35 | ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
36 | ... | DUT1 and DUT2 tested with ${nic_name}.\
37 | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
38 | ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\
39 | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
40 | ... | of packets transmitted. NDR and PDR are discovered for different\
41 | ... | Ethernet L2 frame sizes using MLRsearch library.\
42 | ... | Test packets are generated by TG on links to DUTs. TG traffic profile
43 | ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
44 | ... | flow-group) with all packets containing Ethernet header, IPv4 header
45 | ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
46 | ... | addresses of the TG node interfaces.
47 | ... | *[Ref] Applicable standard specifications:* RFC2544.
48
49 *** Variables ***
50 | @{plugins_to_enable}= | dpdk_plugin.so
51 | ${osi_layer}= | L3
52 | ${nic_name}= | Intel-X710
53 | ${overhead}= | ${0}
54 # Traffic profile:
55 | ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
56
57 *** Keywords ***
58 | Local Template
59 | | ...
60 | | [Documentation]
61 | | ... | [Cfg] DUT runs IPv4 routing config.
62 | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
63 | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
64 | | ...
65 | | ... | *Arguments:*
66 | | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1).
67 | | ... | Type: integer, string
68 | | ... | - phy_cores - Number of physical cores. Type: integer
69 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
70 | | ...
71 | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
72 | | ...
73 | | Set Test Variable | \${frame_size}
74 | | ...
75 | | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
76 | | And Add PCI devices to all DUTs
77 | | And Set Max Rate And Jumbo And Handle Multi Seg
78 | | And Apply startup configuration on all VPP DUTs
79 | | When Initialize IPv4 forwarding in circular topology
80 | | And Add Fib Table | ${dut1} | 1
81 | | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=1 | local=${TRUE}
82 | | And Add Fib Table | ${dut2} | 1
83 | | And Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | vrf=1 | local=${TRUE}
84 | | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip4 | 1
85 | | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip4 | 1
86 | | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
87 | | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
88 | | Then Find NDR and PDR intervals using optimized search
89
90 *** Test Cases ***
91 | tc01-64B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
92 | | [Tags] | 64B | 1C
93 | | frame_size=${64} | phy_cores=${1}
94
95 | tc02-64B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
96 | | [Tags] | 64B | 2C
97 | | frame_size=${64} | phy_cores=${2}
98
99 | tc03-64B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
100 | | [Tags] | 64B | 4C
101 | | frame_size=${64} | phy_cores=${4}
102
103 | tc04-1518B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
104 | | [Tags] | 1518B | 1C
105 | | frame_size=${1518} | phy_cores=${1}
106
107 | tc05-1518B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
108 | | [Tags] | 1518B | 2C
109 | | frame_size=${1518} | phy_cores=${2}
110
111 | tc06-1518B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
112 | | [Tags] | 1518B | 4C
113 | | frame_size=${1518} | phy_cores=${4}
114
115 | tc07-9000B-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
116 | | [Tags] | 9000B | 1C
117 | | frame_size=${9000} | phy_cores=${1}
118
119 | tc08-9000B-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
120 | | [Tags] | 9000B | 2C
121 | | frame_size=${9000} | phy_cores=${2}
122
123 | tc09-9000B-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
124 | | [Tags] | 9000B | 4C
125 | | frame_size=${9000} | phy_cores=${4}
126
127 | tc10-IMIX-1c-ethip4-ip4base-copwhtlistbase-ndrpdr
128 | | [Tags] | IMIX | 1C
129 | | frame_size=IMIX_v4_1 | phy_cores=${1}
130
131 | tc11-IMIX-2c-ethip4-ip4base-copwhtlistbase-ndrpdr
132 | | [Tags] | IMIX | 2C
133 | | frame_size=IMIX_v4_1 | phy_cores=${2}
134
135 | tc12-IMIX-4c-ethip4-ip4base-copwhtlistbase-ndrpdr
136 | | [Tags] | IMIX | 4C
137 | | frame_size=IMIX_v4_1 | phy_cores=${4}