Remove lbdpdk perf tests
[csit.git] / tests / vpp / perf / ip4 / 2n1l-10ge2p1x710-ethip4udp-ip4base-iacl1sl-10kflows-mrr.robot
1 # Copyright (c) 2018 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/performance/performance_setup.robot
16 | ...
17 | Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
18 | ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
19 | ... | IACL | ACL1 | 10k_FLOWS
20 | ...
21 | Suite Setup | Run Keywords
22 | ... | Set up 2-node performance topology with DUT's NIC model | L3
23 | ... | Intel-X710
24 | ... | AND | Set up performance test suite with ACL
25 | Suite Teardown | Tear down 2-node performance topology
26 | ...
27 | Test Setup | Set up performance test
28 | ...
29 | Test Teardown | Tear down performance mrr test
30 | ...
31 | Test Template | Local Template
32 | ...
33 | Documentation | *Raw results IPv4 test cases with ACL*
34 | ...
35 | ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
36 | ... | with single links between nodes.
37 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
38 | ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
39 | ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
40 | ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
41 | ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
42 | ... | at line rate and reports total received/sent packets over trial period.\
43 | ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
44 | ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
45 | ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
46 | ... | header with IP protocol=61 and static payload. MAC addresses are\
47 | ... | matching MAC addresses of the TG node interfaces.
48 | ... | *[Ref] Applicable standard specifications:* RFC2544.
49
50 *** Variables ***
51 # X710 bandwidth limit
52 | ${s_limit}= | ${10000000000}
53
54 # ACL test setup
55 | ${acl_action}= | permit
56 | ${acl_apply_type}= | input
57 | ${no_hit_aces_number}= | 1
58 | ${flows_per_dir}= | 10k
59
60 # starting points for non-hitting ACLs
61 | ${src_ip_start}= | 30.30.30.1
62 | ${dst_ip_start}= | 40.40.40.1
63 | ${ip_step}= | ${1}
64 | ${sport_start}= | ${1000}
65 | ${dport_start}= | ${1000}
66 | ${port_step}= | ${1}
67 | ${trex_stream1_subnet}= | 10.10.10.0/24
68 | ${trex_stream2_subnet}= | 20.20.20.0/24
69
70 | ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
71
72 *** Keywords ***
73 | Local Template
74 | | ...
75 | | [Documentation]
76 | | ... | [Cfg] DUT runs IPv4 routing config.
77 | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
78 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
79 | | ... | trial throughput test.
80 | | ...
81 | | ... | *Arguments:*
82 | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
83 | | ... | Type: integer, string
84 | | ... | - phy_cores - Number of physical cores. Type: integer
85 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
86 | | ...
87 | | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
88 | | ...
89 | | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
90 | | And Add PCI devices to all DUTs
91 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
92 | | ... | ${s_limit} | ${framesize}
93 | | And Apply startup configuration on all VPP DUTs
94 | | ${ip_nr}= | Set Variable | 10
95 | | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
96 | | Then Traffic should pass with maximum rate
97 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
98
99 *** Test Cases ***
100 | tc01-64B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
101 | | [Tags] | 64B | 1C
102 | | framesize=${64} | phy_cores=${1}
103
104 | tc02-64B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
105 | | [Tags] | 64B | 2C
106 | | framesize=${64} | phy_cores=${2}
107
108 | tc03-64B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
109 | | [Tags] | 64B | 4C
110 | | framesize=${64} | phy_cores=${4}
111
112 | tc04-1518B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
113 | | [Tags] | 1518B | 1C
114 | | framesize=${1518} | phy_cores=${1}
115
116 | tc05-1518B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
117 | | [Tags] | 1518B | 2C
118 | | framesize=${1518} | phy_cores=${2}
119
120 | tc06-1518B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
121 | | [Tags] | 1518B | 4C
122 | | framesize=${1518} | phy_cores=${4}
123
124 | tc07-9000B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
125 | | [Tags] | 9000B | 1C
126 | | framesize=${9000} | phy_cores=${1}
127
128 | tc08-9000B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
129 | | [Tags] | 9000B | 2C
130 | | framesize=${9000} | phy_cores=${2}
131
132 | tc09-9000B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
133 | | [Tags] | 9000B | 4C
134 | | framesize=${9000} | phy_cores=${4}
135
136 | tc10-IMIX-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
137 | | [Tags] | IMIX | 1C
138 | | framesize=IMIX_v4_1 | phy_cores=${1}
139
140 | tc11-IMIX-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
141 | | [Tags] | IMIX | 2C
142 | | framesize=IMIX_v4_1 | phy_cores=${2}
143
144 | tc12-IMIX-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
145 | | [Tags] | IMIX | 4C
146 | | framesize=IMIX_v4_1 | phy_cores=${4}