Remove lbdpdk perf tests
[csit.git] / tests / vpp / perf / ip4_tunnels / 10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot
1 # Copyright (c) 2018 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/performance/performance_setup.robot
16 | ...
17 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
18 | ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_100 | DOT1Q | VLAN_100
19 | ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_100
20 | ...
21 | Suite Setup | Set up 3-node performance topology with DUT's NIC model
22 | ... | L2 | Intel-X520-DA2
23 | Suite Teardown | Tear down 3-node performance topology
24 | ...
25 | Test Setup | Set up performance test
26 | ...
27 | Test Teardown | Tear down performance mrr test
28 | ...
29 | Test Template | Local Template
30 | ...
31 | Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases*
32 | ...
33 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
34 | ... | with single links between nodes.
35 | ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\
36 | ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
37 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 100 L2\
38 | ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\
39 | ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
40 | ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
41 | ... | at line rate and reports total received/sent packets over trial period.\
42 | ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
43 | ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\
44 | ... | flows per flow-group) with all packets containing Ethernet header,\
45 | ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\
46 | ... | MAC addresses are matching MAC addresses of the TG node interfaces.
47 | ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348.
48
49 *** Variables ***
50 # X520-DA2 bandwidth limit
51 | ${s_limit}= | ${10000000000}
52 | ${overhead}= | ${50}
53 # Traffic profile:
54 | ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan100ip4src254ip4dst254
55 # Number of VXLAN tunnels
56 | ${vxlan_count}= | ${100}
57
58 *** Keywords ***
59 | Local Template
60 | | ...
61 | | [Documentation]
62 | | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\
63 | | ... | uses ${phy_cores} physical core(s) for worker threads.
64 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
65 | | ... | trial throughput test.
66 | | ...
67 | | ... | *Arguments:*
68 | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
69 | | ... | Type: integer, string
70 | | ... | - phy_cores - Number of physical cores. Type: integer
71 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
72 | | ...
73 | | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
74 | | ...
75 | | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
76 | | And Add PCI devices to all DUTs
77 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
78 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
79 | | And Apply startup configuration on all VPP DUTs
80 | | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology
81 | | ... | vxlan_count=${vxlan_count}
82 | | Then Traffic should pass with maximum rate
83 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
84
85 *** Test Cases ***
86 | tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
87 | | [Tags] | 64B | 1C
88 | | framesize=${64} | phy_cores=${1}
89
90 | tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
91 | | [Tags] | 64B | 2C
92 | | framesize=${64} | phy_cores=${2}
93
94 | tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
95 | | [Tags] | 64B | 4C
96 | | framesize=${64} | phy_cores=${4}
97
98 | tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
99 | | [Tags] | 1518B | 1C
100 | | framesize=${1518} | phy_cores=${1}
101
102 | tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
103 | | [Tags] | 1518B | 2C
104 | | framesize=${1518} | phy_cores=${2}
105
106 | tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
107 | | [Tags] | 1518B | 4C
108 | | framesize=${1518} | phy_cores=${4}
109
110 | tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
111 | | [Tags] | 9000B | 1C
112 | | framesize=${9000} | phy_cores=${1}
113
114 | tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
115 | | [Tags] | 9000B | 2C
116 | | framesize=${9000} | phy_cores=${2}
117
118 | tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
119 | | [Tags] | 9000B | 4C
120 | | framesize=${9000} | phy_cores=${4}
121
122 | tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
123 | | [Tags] | IMIX | 1C
124 | | framesize=IMIX_v4_1 | phy_cores=${1}
125
126 | tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
127 | | [Tags] | IMIX | 2C
128 | | framesize=IMIX_v4_1 | phy_cores=${2}
129
130 | tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
131 | | [Tags] | IMIX | 4C
132 | | framesize=IMIX_v4_1 | phy_cores=${4}