[csit.git] / tests / vpp / perf / ip6 / 10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdr.robot

# Copyright (c) 2018 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.

*** Settings ***
| Resource | resources/libraries/robot/performance/performance_setup.robot
| Library | resources.libraries.python.Cop
| ...
| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | COPWHLIST
| ...
| Suite Setup | Set up 3-node performance topology with DUT's NIC model
| ... | L3 | Intel-X520-DA2
| Suite Teardown | Tear down 3-node performance topology
| ...
| Test Setup | Set up performance test
| ...
| Test Teardown | Tear down performance discovery test | ${min_rate}pps
| ... | ${framesize} | ${traffic_profile}
| ...
| Test Template | Local Template
| ...
| Documentation | *RFC2544: Pkt throughput IPv6 whitelist test cases*
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
| ... | with single links between nodes.
| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist
| ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG.
| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
| ... | of packets transmitted. NDR and PDR are discovered for different
| ... | Ethernet L2 frame sizes using MLRsearch library.
| ... | Test packets are generated by TG on
| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
| ... | (flow-group per direction, 253 flows per flow-group) with all packets
| ... | containing Ethernet header, IPv6 header and static
| ... | payload. MAC addresses are matching MAC addresses of the TG node
| ... | interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.

*** Variables ***
# X520-DA2 bandwidth limit
| ${s_limit} | ${10000000000}
# Traffic profile:
| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253

*** Keywords ***
| Local Template
| | [Documentation]
| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with
| | ... | ${phy_cores} phy core(s) for worker threads.\
| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
| | ...
| | ... | *Arguments:*
| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
| | ... | Type: integer, string
| | ... | - phy_cores - Number of physical cores. Type: integer
| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
| | ...
| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
| | ...
| | Set Test Variable | ${framesize}
| | Set Test Variable | ${min_rate} | ${10000}
| | ...
| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
| | And Add PCI devices to all DUTs
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | When Initialize IPv6 forwarding in 3-node circular topology
| | And Add Fib Table | ${dut1} | 1 | ipv6=${TRUE}
| | And Vpp Route Add | ${dut1} | 2001:1:: | 64 | vrf=1 | local=${TRUE}
| | And Add Fib Table | ${dut2} | 1 | ipv6=${TRUE}
| | And Vpp Route Add | ${dut2} | 2001:2:: | 64 | vrf=1 | local=${TRUE}
| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}

*** Test Cases ***
| tc01-78B-1c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 78B | 1C
| | framesize=${78} | phy_cores=${1}

| tc02-78B-2c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 78B | 2C
| | framesize=${78} | phy_cores=${2}

| tc03-78B-4c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 78B | 4C
| | framesize=${78} | phy_cores=${4}

| tc04-1518B-1c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 1518B | 1C
| | framesize=${1518} | phy_cores=${1}

| tc05-1518B-2c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 1518B | 2C
| | framesize=${1518} | phy_cores=${2}

| tc06-1518B-4c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 1518B | 4C
| | framesize=${1518} | phy_cores=${4}

| tc07-9000B-1c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 9000B | 1C
| | framesize=${9000} | phy_cores=${1}

| tc08-9000B-2c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 9000B | 2C
| | framesize=${9000} | phy_cores=${2}

| tc09-9000B-4c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | 9000B | 4C
| | framesize=${9000} | phy_cores=${4}

| tc10-IMIX-1c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | IMIX | 1C
| | framesize=IMIX_v4_1 | phy_cores=${1}

| tc11-IMIX-2c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | IMIX | 2C
| | framesize=IMIX_v4_1 | phy_cores=${2}

| tc12-IMIX-4c-ethip6-ip6base-copwhtlistbase-ndrpdr
| | [Tags] | IMIX | 4C
| | framesize=IMIX_v4_1 | phy_cores=${4}