Add MTU handling into perf tests
[csit.git] / tests / vpp / perf / l2 / 10ge2p1x710-dot1q-l2xcbase-ndrpdr.robot
1 # Copyright (c) 2018 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/performance/performance_setup.robot
16 | Resource | resources/libraries/robot/l2/tagging.robot
17 | ...
18 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
19 | ... | NIC_Intel-X710 | L2XCFWD | BASE | DOT1Q
20 | ...
21 | Suite Setup | Set up 3-node performance topology with DUT's NIC model
22 | ... | L2 | Intel-X710
23 | ...
24 | Suite Teardown | Tear down 3-node performance topology
25 | ...
26 | Test Setup | Set up performance test
27 | ...
28 | Test Teardown | Tear down performance discovery test | ${min_rate}pps
29 | ... | ${framesize} | ${traffic_profile}
30 | ...
31 | Test Template | Local Template
32 | ...
33 | Documentation | *RFC2544: Pkt throughput L2XC with 802.1q test cases*
34 | ...
35 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
36 | ... | with single links between nodes.
37 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q\
38 | ... | tagging is applied on link between DUT1 and DUT2.
39 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-\
40 | ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
41 | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
42 | ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
43 | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
44 | ... | of packets transmitted. NDR and PDR are discovered for different
45 | ... | Ethernet L2 frame sizes using MLRsearch library.
46 | ... | Test packets are generated by TG on\
47 | ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
48 | ... | (flow-group per direction, 253 flows per flow-group) with all packets\
49 | ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
50 | ... | payload. MAC addresses are matching MAC addresses of the TG node\
51 | ... | interfaces.
52 | ... | *[Ref] Applicable standard specifications:* RFC2544.
53
54 *** Variables ***
55 | ${subid}= | 10
56 | ${tag_rewrite}= | pop-1
57 | ${overhead}= | ${4}
58 # X710-DA2 bandwidth limit
59 | ${s_limit}= | ${10000000000}
60 # Traffic profile:
61 | ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254
62
63 *** Keywords ***
64 | Local Template
65 | | [Documentation]
66 | | ... | [Cfg] DUT runs L2XC config with VLAN dot1q with ${phy_cores} phy
67 | | ... | core(s).
68 | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
69 | | ...
70 | | ... | *Arguments:*
71 | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
72 | | ... | Type: integer, string
73 | | ... | - phy_cores - Number of physical cores. Type: integer
74 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
75 | | ...
76 | | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
77 | | ...
78 | | Set Test Variable | ${framesize}
79 | | Set Test Variable | ${min_rate} | ${10000}
80 | | ...
81 | | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
82 | | And Add PCI devices to all DUTs
83 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
84 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
85 | | And Apply startup configuration on all VPP DUTs
86 | | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology
87 | | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid}
88 | | And Configure L2 tag rewrite method on interfaces
89 | | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
90 | | ... | ${tag_rewrite}
91 | | And Connect interfaces and VLAN sub-interfaces using L2XC
92 | | ... | ${dut1} | ${dut1_if1} | ${subif_index_1}
93 | | ... | ${dut2} | ${dut2_if2} | ${subif_index_2}
94 | | Then Find NDR and PDR intervals using optimized search
95 | | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
96
97 *** Test Cases ***
98 | tc01-64B-1c-dot1q-l2xcbase-ndrpdr
99 | | [Tags] | 64B | 1C
100 | | framesize=${64} | phy_cores=${1}
101
102 | tc02-64B-2c-dot1q-l2xcbase-ndrpdr
103 | | [Tags] | 64B | 2C
104 | | framesize=${64} | phy_cores=${2}
105
106 | tc03-64B-4c-dot1q-l2xcbase-ndrpdr
107 | | [Tags] | 64B | 4C
108 | | framesize=${64} | phy_cores=${4}
109
110 | tc04-1518B-1c-dot1q-l2xcbase-ndrpdr
111 | | [Tags] | 1518B | 1C
112 | | framesize=${1518} | phy_cores=${1}
113
114 | tc05-1518B-2c-dot1q-l2xcbase-ndrpdr
115 | | [Tags] | 1518B | 2C
116 | | framesize=${1518} | phy_cores=${2}
117
118 | tc06-1518B-4c-dot1q-l2xcbase-ndrpdr
119 | | [Tags] | 1518B | 4C
120 | | framesize=${1518} | phy_cores=${4}
121
122 | tc07-9000B-1c-dot1q-l2xcbase-ndrpdr
123 | | [Tags] | 9000B | 1C
124 | | framesize=${9000} | phy_cores=${1}
125
126 | tc08-9000B-2c-dot1q-l2xcbase-ndrpdr
127 | | [Tags] | 9000B | 2C
128 | | framesize=${9000} | phy_cores=${2}
129
130 | tc09-9000B-4c-dot1q-l2xcbase-ndrpdr
131 | | [Tags] | 9000B | 4C
132 | | framesize=${9000} | phy_cores=${4}
133
134 | tc10-IMIX-1c-dot1q-l2xcbase-ndrpdr
135 | | [Tags] | IMIX | 1C
136 | | framesize=IMIX_v4_1 | phy_cores=${1}
137
138 | tc11-IMIX-2c-dot1q-l2xcbase-ndrpdr
139 | | [Tags] | IMIX | 2C
140 | | framesize=IMIX_v4_1 | phy_cores=${2}
141
142 | tc12-IMIX-4c-dot1q-l2xcbase-ndrpdr
143 | | [Tags] | IMIX | 4C
144 | | framesize=IMIX_v4_1 | phy_cores=${4}