Support suite tags in autogen
[csit.git] / tests / vpp / perf / l2 / 2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-gbp-ndrpdr.robot
1 # Copyright (c) 2019 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/shared/default.robot
16 |
17 | Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
18 | ... | NIC_Intel-X710 | DOT1Q | L2BDMACLRN | BASE | DRV_VFIO_PCI | GBP
19 | ... | dot1q-l2bdbasemaclrn-gbp
20 |
21 | Suite Setup | Setup suite single link | performance
22 | Suite Teardown | Tear down suite | performance
23 | Test Setup | Setup test
24 | Test Teardown | Tear down test | performance
25 |
26 | Test Template | Local template
27 |
28 | Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and GBP test
29 | ... | cases*
30 |
31 | ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
32 | ... | with single links between nodes.
33 | ... | *[Enc] Packet Encapsulations:* Dot1q-IPv4 for L2 switching of IPv4. \
34 | ... | IEEE 802.1Q tagging is applied on both links TG-DUT1 .
35 | ... | *[Cfg] DUT configuration:* DUT1 is configured with:\
36 | ... | 2 VLAN subinterfaces (VID 100 and 200),\
37 | ... | 1 L2 BD with the 2 VLAN subinterfaces and a BVI,\
38 | ... | 1 GBP L3 RD,\
39 | ... | 1 GBP L2 BD with the L2 BD,\
40 | ... | 1 GBP EPG EPG-1 with sclass 100, the GBP L2 BD and L3 RD,\
41 | ... | 2 GBP external EP in EPG-1,\
42 | ... | 2 external subnets with sclass 200 and 300,\
43 | ... | Contracts allowing full communications between the 2 external subnets.\
44 | ... | DUT1 tested with ${nic_name} with VF enabled.
45 | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
46 | ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\
47 | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
48 | ... | of packets transmitted. NDR and PDR are discovered for different\
49 | ... | Ethernet L2 frame sizes using MLRsearch library.\
50 | ... | Test packets are generated by TG on\
51 | ... | links to DUT. TG traffic profile contains two L3 flow-groups\
52 | ... | (flow-group per direction, 254 flows per flow-group) with all packets\
53 | ... | containing Ethernet header including IEEE 802.1Q tagging, IPv4 header\
54 | ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
55 | ... | addresses of the TG node interfaces.
56 | ... | *[Ref] Applicable standard specifications:* RFC2544.
57
58 *** Variables ***
59 | @{plugins_to_enable}= | dpdk_plugin.so | gbp_plugin.so | acl_plugin.so
60 | ${crypto_type}= | ${None}
61 | ${nic_name}= | Intel-X710
62 | ${nic_driver}= | vfio-pci
63 | ${osi_layer}= | L2
64 | ${overhead}= | ${4}
65 # Traffic profile:
66 | ${traffic_profile}= | trex-sl-dot1qip4-vlan1ip4src254ip4dst254-bvi
67
68 *** Keywords ***
69 | Local template
70 | | [Documentation]
71 | | ... | [Cfg] DUT runs L2BD with VLAN and GBP config with ${phy_cores}\
72 | | ... | physical core(s) for worker threads.
73 | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
74 | |
75 | | ... | *Arguments:*
76 | | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1).
77 | | ... | Type: integer, string
78 | | ... | - phy_cores - Number of physical cores. Type: integer
79 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
80 | |
81 | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
82 | |
83 | | Set Test Variable | \${frame_size}
84 | |
85 | | Given Set Max Rate And Jumbo
86 | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
87 | | And Pre-initialize layer driver | ${nic_driver}
88 | | And Apply Startup configuration on all VPP DUTs
89 | | When Initialize layer driver | ${nic_driver}
90 | | And Initialize layer interface
91 | | And Initialize layer dot1q
92 | | And Initialize GBP routing domains
93 | | Then Find NDR and PDR intervals using optimized search
94
95 *** Test Cases ***
96 | tc01-64B-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
97 | | [Tags] | 64B | 1C
98 | | frame_size=${64} | phy_cores=${1}
99
100 | tc02-64B-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
101 | | [Tags] | 64B | 2C
102 | | frame_size=${64} | phy_cores=${2}
103
104 | tc03-64B-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
105 | | [Tags] | 64B | 4C
106 | | frame_size=${64} | phy_cores=${4}
107
108 | tc04-1518B-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
109 | | [Tags] | 1518B | 1C
110 | | frame_size=${1518} | phy_cores=${1}
111
112 | tc05-1518B-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
113 | | [Tags] | 1518B | 2C
114 | | frame_size=${1518} | phy_cores=${2}
115
116 | tc06-1518B-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
117 | | [Tags] | 1518B | 4C
118 | | frame_size=${1518} | phy_cores=${4}
119
120 | tc07-9000B-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
121 | | [Tags] | 9000B | 1C
122 | | frame_size=${9000} | phy_cores=${1}
123
124 | tc08-9000B-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
125 | | [Tags] | 9000B | 2C
126 | | frame_size=${9000} | phy_cores=${2}
127
128 | tc09-9000B-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
129 | | [Tags] | 9000B | 4C
130 | | frame_size=${9000} | phy_cores=${4}
131
132 | tc10-IMIX-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
133 | | [Tags] | IMIX | 1C
134 | | frame_size=IMIX_v4_1 | phy_cores=${1}
135
136 | tc11-IMIX-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
137 | | [Tags] | IMIX | 2C
138 | | frame_size=IMIX_v4_1 | phy_cores=${2}
139
140 | tc12-IMIX-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
141 | | [Tags] | IMIX | 4C
142 | | frame_size=IMIX_v4_1 | phy_cores=${4}