# Copyright (c) 2016 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Variables *** # Interface to run tests on. | ${interface}= | ${node['interfaces']['port1']['name']} # Configuration which will be set and verified during tests. | ${ipv4_address}= | 192.168.0.2 | ${ipv4_address2}= | 192.168.0.3 | ${ipv4_mask}= | 255.255.255.0 | ${ipv4_prefix}= | ${24} | @{ipv4_neighbor}= | 192.168.0.4 | 08:00:27:c0:5d:37 | &{ipv4_settings}= | enabled=${True} | forwarding=${True} | mtu=${9000} | @{ipv6_address}= | 10::10 | ${64} | @{ipv6_neighbor}= | 10::11 | 08:00:27:c0:5d:37 | &{ipv6_settings}= | enabled=${True} | forwarding=${True} | mtu=${9000} | ... | dup-addr-detect-transmits=${5} | &{ethernet}= | mtu=${9000} | &{routing}= | vrf-id=${27} | &{vxlan_settings}= | src=10.0.1.20 | dst=10.0.3.20 | vni=${1000} | ... | encap-vrf-id=${1000} *** Settings *** | Resource | resources/libraries/robot/default.robot | Resource | resources/libraries/robot/honeycomb/interfaces.robot | Force Tags | honeycomb_sanity | Documentation | *Honeycomb interface management test suite.* | ... | ... | Test suite uses the first interface of the first DUT node. *** Test Cases *** | Honeycomb configures and reads interface state | | [Documentation] | Check if Honeycomb API can modify the admin state of\ | | ... | VPP interfaces. | | Given Interface state is | ${node} | ${interface} | down | | When Honeycomb sets interface state | ${node} | ${interface} | up | | Then Interface state from Honeycomb should be | | ... | ${node} | ${interface} | up | | And Interface state from VAT should be | ${node} | ${interface} | up | | When Honeycomb sets interface state | ${node} | ${interface} | down | | Then Interface state from Honeycomb should be | | ... | ${node} | ${interface} | down | | And Interface state from VAT should be | ${node} | ${interface} | down | Honeycomb modifies interface configuration - ipv4 (netmask) | | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4\ | | ... | with address and netmask provided. | | When Honeycomb sets interface ipv4 address | ${node} | ${interface} | | ... | ${ipv4_address} | ${ipv4_mask} | ${ipv4_settings} | | And Honeycomb adds interface ipv4 neighbor | | ... | ${node} | ${interface} | @{ipv4_neighbor} | | Then IPv4 config from Honeycomb should be | | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix} | | ... | @{ipv4_neighbor} | ${ipv4_settings} | | And IPv4 config from VAT should be | | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix} | Honeycomb removes ipv4 address from interface | | [Documentation] | Check if Honeycomb API can remove configured ipv4\ | | ... | addresses from interface. | | Given IPv4 config from Honeycomb should be | | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix} | | ... | @{ipv4_neighbor} | ${ipv4_settings} | | And IPv4 config from VAT should be | | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix} | | When Honeycomb removes interface ipv4 addresses | ${node} | ${interface} | | Then IPv4 address from Honeycomb should be empty | ${node} |${interface} | | And ipv4 address from VAT should be empty | ${node} | ${interface} | Honeycomb modifies interface configuration - ipv4 (prefix) | | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4\ | | ... | with address and prefix provided. | | [Teardown] | Honeycomb removes interface ipv4 addresses | ${node} | | ... | ${interface} | | When Honeycomb sets interface ipv4 address with prefix | | ... | ${node} | ${interface} | ${ipv4_address2} | ${ipv4_prefix} | | ... | ${ipv4_settings} | | And Honeycomb adds interface ipv4 neighbor | | ... | ${node} | ${interface} | @{ipv4_neighbor} | | Then IPv4 config from Honeycomb should be | | ... | ${node} | ${interface} | ${ipv4_address2} | ${ipv4_prefix} | | ... | @{ipv4_neighbor} | | ... | ${ipv4_settings} | | And IPv4 config from VAT should be | | ... | ${node} | ${interface} | ${ipv4_address2} | ${ipv4_prefix} | Honeycomb modifies interface configuration - ipv6 | | [Documentation] | Check if Honeycomb API can configure interfaces for ipv6. | | When Honeycomb sets interface ipv6 configuration | | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor} | | ... | ${ipv6_settings} | | Then IPv6 config from Honeycomb should be | | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor} | | ... | ${ipv6_settings} | | And IPv6 config from VAT should be | | ... | ${node} | ${interface} | @{ipv6_address} | Honeycomb modifies interface configuration - ethernet,routing | | [Documentation] | Check if Honeycomb API can configure interface ethernet\ | | ... | and routing settings. | | When Honeycomb sets interface ethernet and routing configuration | | ... | ${node} | ${interface} | ${ethernet} | ${routing} | | Then Interface ethernet and routing configuration from Honeycomb should be | | ... | ${node} | ${interface} | ${ethernet} | ${routing} | | And Interface ethernet and routing configuration from VAT should be | | ... | ${node} | ${interface} | ${ethernet['mtu']} | ${routing['vrf-id']}