# Copyright (c) 2017 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/performance.robot | Library | resources.libraries.python.Classify.Classify | ... | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC | ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | IACLDST | ... | Suite Setup | 3-node Performance Suite Setup with DUT's NIC model | ... | L3 | Intel-X520-DA2 | Suite Teardown | 3-node Performance Suite Teardown | ... | Test Setup | Performance test setup | Test Teardown | Performance test teardown | ${min_rate}pps | ${framesize} | ... | 3-node-IPv6 | ... | Documentation | *RFC2544: Pkt throughput IPv6 iAcl whitelist test cases* | ... | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology | ... | with single links between nodes. | ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 | ... | routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist | ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. | ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop | ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage | ... | of packets transmitted. NDR and PDR are discovered for different | ... | Ethernet L2 frame sizes using either binary search or linear search | ... | algorithms with configured starting rate and final step that determines | ... | throughput measurement resolution. Test packets are generated by TG on | ... | links to DUTs. TG traffic profile contains two L3 flow-groups | ... | (flow-group per direction, 253 flows per flow-group) with all packets | ... | containing Ethernet header, IPv6 header and generated payload. MAC | ... | addresses are matching MAC addresses of the TG node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544. *** Variables *** # X520-DA2 bandwidth limit | ${s_limit} | ${10000000000} *** Test Cases *** | tc01-78B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR | | ... | for 78 Byte frames using binary search start at 10GE linerate, | | ... | step 100kpps. | | [Tags] | 78B | 1T1C | STHREAD | NDRDISC | | ${framesize}= | Set Variable | ${78} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc02-78B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR | | ... | for 78 Byte frames using binary search start at 10GE linerate, | | ... | step 100kpps, LT=0.5%. | | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${78} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc03-1518B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR | | ... | for 1518 Byte frames using binary search start at 10GE linerate, | | ... | step 10kpps. | | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc04-1518B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR | | ... | for 1518 Byte frames using binary search start at 10GE linerate, | | ... | step 10kpps, LT=0.5%. | | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc05-9000B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR | | ... | for 9000 Byte frames using binary search start at 10GE linerate, | | ... | step 5kpps. | | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc06-9000B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR | | ... | for 9000 Byte frames using binary search start at 10GE linerate, | | ... | step 5kpps, LT=0.5%. | | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc07-78B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR | | ... | for 78 Byte frames using binary search start at 10GE linerate, | | ... | step 100kpps. | | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC | | ${framesize}= | Set Variable | ${78} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc08-78B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR | | ... | for 78 Byte frames using binary search start at 10GE linerate, | | ... | step 100kpps, LT=0.5%. | | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${78} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc09-1518B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR | | ... | for 1518 Byte frames using binary search start at 10GE linerate, | | ... | step 10kpps. | | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc10-1518B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR | | ... | for 1518 Byte frames using binary search start at 10GE linerate, | | ... | step 10kpps, LT=0.5%. | | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc11-9000B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR | | ... | for 9000 Byte frames using binary search start at 10GE linerate, | | ... | step 5kpps. | | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc12-9000B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR | | ... | for 9000 Byte frames using binary search start at 10GE linerate, | | ... | step 5kpps, LT=0.5%. | | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc13-78B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR | | ... | for 78 Byte frames using binary search start at 10GE linerate, | | ... | step 100kpps. | | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC | | ${framesize}= | Set Variable | ${78} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc14-78B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR | | ... | for 78 Byte frames using binary search start at 10GE linerate, | | ... | step 100kpps, LT=0.5%. | | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${78} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc15-1518B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR | | ... | for 1518 Byte frames using binary search start at 10GE linerate, | | ... | step 10kpps. | | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc16-1518B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR | | ... | for 1518 Byte frames using binary search start at 10GE linerate, | | ... | step 10kpps, LT=0.5%. | | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc17-9000B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR | | ... | for 9000 Byte frames using binary search start at 10GE linerate, | | ... | step 5kpps. | | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc18-9000B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ | | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR | | ... | for 9000 Byte frames using binary search start at 10GE linerate, | | ... | step 5kpps, LT=0.5%. | | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | And IPv6 forwarding initialized in a 3-node circular topology | | And IPv6 iAcl whitelist initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv6 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type}