# Copyright (c) 2017 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/performance.robot | Library | resources.libraries.python.NodePath | ... | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC | ... | NIC_Cisco-VIC-1385 | ETH | L2BDMACLRN | BASE | ... | Suite Setup | 3-node Performance Suite Setup with DUT's NIC model | ... | L2 | Cisco-VIC-1385 | Suite Teardown | 3-node Performance Suite Teardown | ... | Test Setup | Performance test setup | Test Teardown | Performance test teardown | ${min_rate}pps | ${framesize} | ... | 3-node-bridge | ... | Documentation | *RFC2544: Pkt throughput L2BD test cases* | ... | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology | ... | with single links between nodes. | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- | ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p40GE NIC | ... | NIC_Cisco-VIC-1385. | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop | ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage | ... | of packets transmitted. NDR and PDR are discovered for different | ... | Ethernet L2 frame sizes using either binary search or linear search | ... | algorithms with configured starting rate and final step that determines | ... | throughput measurement resolution. Test packets are generated by TG on | ... | links to DUTs. TG traffic profile contains two L3 flow-groups | ... | (flow-group per direction, 253 flows per flow-group) with all packets | ... | containing Ethernet header, IPv4 header with IP protocol=61 and static | ... | payload. MAC addresses are matching MAC addresses of the TG node | ... | interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544. *** Variables *** # XL710-DA2 (TG) bandwidth limit ~49Gbps/2=24.5Gbps | ${s_24.5G} | ${24500000000} # XL710-DA2 Mpps (TG) limit 37.5Mpps/2=18.75Mpps | ${s_18.75Mpps} | ${18750000} *** Test Cases *** | tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ | | ... | 18.75Mpps rate, step 100kpps. | | ... | | [Tags] | 64B | 1T1C | STHREAD | NDRDISC | | ... | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Set Variable | ${s_18.75Mpps} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\ | | ... | 18.75Mpps rate, step 100kpps. | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Set Variable | ${s_18.75Mpps} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ | | ... | 24.5G rate, step 10kpps. | | ... | | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC | | ... | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ | | ... | 24.5G rate, step 10kpps. | | ... | | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC | | ... | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ | | ... | 18.75Mpps rate, step 100kpps. | | ... | | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC | | ... | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Set Variable | ${s_18.75Mpps} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\ | | ... | 18.75Mpps rate, step 100kpps. | | ... | | [Tags] | 64B | 2T2C | MTHREAD | PDR | SKIP_PATCH | | ... | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Set Variable | ${s_18.75Mpps} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | ${perf_pdr_loss_acceptance} | | ... | ${perf_pdr_loss_acceptance_type} | tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ | | ... | 24.5G rate, step 10kpps. | | ... | | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH | | ... | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ | | ... | 18.75Mpps rate, step 100kpps. | | ... | | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC | | ... | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Set Variable | ${s_18.75Mpps} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ | | ... | 24.5G rate, step 10kpps. | | ... | | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH | | ... | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc19-IMIX-1t1c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ | | ... | 24.5G rate, step 100kpps. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | ... | | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC | | ... | | ${framesize}= | Set Variable | IMIX_v4_1 | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc20-IMIX-2t2c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ | | ... | 24.5G rate, step 100kpps. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | ... | | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH | | ... | | ${framesize}= | Set Variable | IMIX_v4_1 | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold} | tc21-IMIX-4t4c-eth-l2bdbasemaclrn-ndrdisc | | [Documentation] | | ... | [Cfg] DUT runs L2BD switching config with 4 thread, 4 phy core,\ | | ... | 2 receive queue per NIC port. | | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ | | ... | 24.5G rate, step 100kpps. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | ... | | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH | | ... | | ${framesize}= | Set Variable | IMIX_v4_1 | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | And L2 bridge domain initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} | | ... | ${threshold}