# Copyright (c) 2016 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/performance.robot | Library | resources.libraries.python.Policer | Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']} | WITH NAME | dut1_v4 | Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']} | WITH NAME | dut2_v4 | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_LONG | ... | NIC_Intel-X520-DA2 | Suite Setup | 3-node Performance Suite Setup with DUT's NIC model | ... | L3 | Intel-X520-DA2 | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keywords | ... | Run Keyword If Test Failed | ... | Traffic should pass with no loss | 10 | ... | ${min_rate}pps | ${framesize} | 3-node-IPv4 | ... | fail_on_loss=${False} | ... | AND | Remove startup configuration of VPP from all DUTs | ... | AND | Show vpp trace dump on all DUTs | Documentation | *RFC2544: Pkt throughput IPv4 policer test cases* | ... | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology | ... | with single links between nodes. | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 | ... | routing and two static IPv4 /24 route entries and policer with 2R3C | ... | color-aware configuration. Policer is applied on links TG - DUT1 and | ... | DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop | ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage | ... | of packets transmitted. NDR and PDR are discovered for different | ... | Ethernet L2 frame sizes using either binary search or linear search | ... | algorithms with configured starting rate and final step that determines | ... | throughput measurement resolution. Test packets are generated by TG on | ... | links to DUTs. TG traffic profile contains two L3 flow-groups | ... | (flow-group per direction, 253 flows per flow-group) with all packets | ... | containing Ethernet header, IPv4 header with IP protocol=61 and | ... | generated payload. MAC addresses are matching MAC addresses of the TG | ... | node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698. *** Variables *** #X520-DA2 bandwidth limit | ${s_limit} | ${10000000000} | ${cir}= | ${100} | ${eir}= | ${150} *** Test Cases *** | TC01: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 \ | | ... | phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 100kpps. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC02: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 \ | | ... | phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 100kpps, LT=0.5%. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC03: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 \ | | ... | phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 \ | | ... | Byte frames using binary search start at 10GE linerate, step 10kpps. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC04: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 \ | | ... | phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 10kpps, LT=0.5%. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC05: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 \ | | ... | phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 \ | | ... | Byte frames using binary search start at 10GE linerate, step 5kpps. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${5000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC06: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 \ | | ... | phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 \ | | ... | Byte frames using binary search start at 10GE linerate, step 5kpps, \ | | ... | LT=0.5%. | | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${5000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC07: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ | | ... | phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 100kpps. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC08: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ | | ... | phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 100kpps, LT=0.5%. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC09: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ | | ... | phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 \ | | ... | Byte frames using binary search start at 10GE linerate, step 10kpps. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC10: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ | | ... | phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 10kpps, LT=0.5%. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC11: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ | | ... | phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 \ | | ... | Byte frames using binary search start at 10GE linerate, step 5kpps. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${5000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC12: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ | | ... | phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 \ | | ... | Byte frames using binary search start at 10GE linerate, step 5kpps, \ | | ... | LT=0.5%. | | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${5000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC13: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 \ | | ... | phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 \ | | ... | Byte frames using binary search start at 10GE linerate, step 100kpps. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC14: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 \ | | ... | phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 100kpps, LT=0.5%. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${64} | | ${min_rate}= | Set Variable | ${100000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC15: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 \ | | ... | phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 \ | | ... | Byte frames using binary search start at 10GE linerate, step 10kpps. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC16: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 \ | | ... | phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 \ | | ... | Byte frames using binary search start at 10GE linerate, step \ | | ... | 10kpps, LT=0.5%. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${1518} | | ${min_rate}= | Set Variable | ${10000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} | TC17: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 \ | | ... | phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 \ | | ... | Byte frames using binary search start at 10GE linerate, step 5kpps. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${5000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | TC18: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq | | [Documentation] | | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 \ | | ... | phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 \ | | ... | Byte frames using binary search start at 10GE linerate, step 5kpps, \ | | ... | LT=0.5%. | | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH | | ${framesize}= | Set Variable | ${9000} | | ${min_rate}= | Set Variable | ${5000} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} | | Set Test Variable | ${cb} | ${framesize} | | Set Test Variable | ${eb} | ${framesize} | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When IPv4 forwarding initialized in a 3-node circular topology | | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology | | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} | | ... | ${binary_max} | 3-node-IPv4 | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type}