# Copyright (c) 2016 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/performance.robot | Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot | Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']} | ... | WITH NAME | dut1_v4 | Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']} | ... | WITH NAME | dut2_v4 # import additional Lisp settings from resource file | Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_SHORT | ... | NIC_Intel-X520-DA2 | Suite Setup | 3-node Performance Suite Setup with DUT's NIC model | ... | L3 | Intel-X520-DA2 | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs | Documentation | *Reference NDR throughput Lisp tunnel verify test cases* | ... | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology | ... | with single links between nodes. | ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, | ... | Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel; | ... | Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for | ... | IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 | ... | tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on | ... | TG-DUTn for IPv6 routing over LISPoIPv4 tunnel. | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 (IPv6) | ... | routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured | ... | between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic | ... | by Intel. | ... | *[Ver] TG verification:* In short performance tests, TG verifies | ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet | ... | loss tolerance. Ref-NDR value is periodically updated acording to | ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long | ... | performance tests for the same DUT confiiguration. Test packets are | ... | generated by TG on links to DUTs. TG traffic profile contains two L3 | ... | flow-groups (flow-group per direction, 253 flows per flow-group) with | ... | all packets containing Ethernet header, IPv4 header or IPv6 header with | ... | IP protocol=61 and generated payload. | ... | *[Ref] Applicable standard specifications:* RFC2544. *** Test Cases *** | TC01: Verify 64B ref-NDR at 2x 1.9Mpps - DUT IPv4 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial throughput | | ... | test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 1.9mpps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC02: Verify 1480B ref-NDR at 2x 740kpps - DUT IPv4 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1480 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 1480 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 740000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC03: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv4 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC04: Verify 64B ref-NDR at 2x 3.6Mpps - DUT IPv4 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.6mpps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC05: Verify 1480B ref-NDR at 2x 740kpps - DUT IPv4 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1480 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 1480 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 740000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC06: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv4 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC07: Verify 64B ref-NDR at 2x 3.5Mpps - DUT IPv4 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.5mpps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC08: Verify 1480B ref-NDR at 2x 740kpps - DUT IPv4 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 1480 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 1480 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 740000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC09: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv4 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv4 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} | | ... | ${dut2_to_tg_ip4} | ${prefix4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} | | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC10: Verify 78B ref-NDR at 2x 1.56Mpps - DUT IPv6 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 1.56mpps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC11: Verify 1460B ref-NDR at 2x 740kpps - DUT IPv6 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 740000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC12: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC13: Verify 78B ref-NDR at 2x 3.2Mpps - DUT IPv6 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 thread, 2 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.2mpps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC14: Verify 1460B ref-NDR at 2x 740kpps - DUT IPv6 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 740000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC15: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC16: Verify 78B ref-NDR at 2x 3.2Mpps - DUT IPv6 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.2mpps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC17: Verify 1460B ref-NDR at 2x 740kpps - DUT IPv6 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 740000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC18: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv6 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} | | ... | ${dut2_to_tg_ip6} | ${prefix6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} | | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC19: Verify 64B ref-NDR at 2x 1.53Mpps - DUT IPv4oIPv6 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 1.53mpps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC20: Verify 1460B ref-NDR at 2x 720kpps - DUT IPv4oIPv6 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 720000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC21: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv4oIPv6 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC22: Verify 64B ref-NDR at 2x 3.25Mpps - DUT IPv4oIPv6 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.25mpps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC23: Verify 1460B ref-NDR at 2x 720kpps - DUT IPv4oIPv6 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 720000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC24: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv4oIPv6 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC25: Verify 64B ref-NDR at 2x 3.12Mpps - DUT IPv4oIPv6 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 64 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.12mpps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC26: Verify 1460B ref-NDR at 2x 720kpps - DUT IPv4oIPv6 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 720000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC27: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv4oIPv6 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} | | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} | | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv4 | TC28: Verify 78B ref-NDR at 2x 1.75Mpps - DUT IPv6oIPv4 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 1.75mpps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC29: Verify 1460B ref-NDR at 2x 720kpps - DUT IPv6oIPv4 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 720000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC30: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6oIPv4 - 1thread 1core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC31: Verify 78B ref-NDR at 2x 3.42Mpps - DUT IPv6oIPv4 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.42mpps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC32: Verify 1460B ref-NDR at 2x 720kpps - DUT IPv6oIPv4 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 720000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC33: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6oIPv4 - 2thread 2core 1rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores, \ | | ... | 1 receive queue per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC34: Verify 78B ref-NDR at 2x 3.42Mpps - DUT IPv6oIPv4 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 78 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 3.42mpps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC35: Verify 1460B ref-NDR at 2x 720Kpps - DUT IPv6oIPv4 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 1460 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 720000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6 | TC36: Verify 9000B ref-NDR at 2x 120Kpps - DUT IPv6oIPv4 - 4thread 4core 2rxq | | [Documentation] | | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores, \ | | ... | 2 receive queues per NIC port. | | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial | | ... | throughput test. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | | ${framesize}= | Set Variable | 9000 | | ${duration}= | Set Variable | 10 | | ${rate}= | Set Variable | 120000pps | | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add PCI devices to DUTs from 3-node single link topology | | And Apply startup configuration on all VPP DUTs | | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology | | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} | | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} | | And Set up Lisp topology | | ... | ${dut1} | ${dut1_if2} | ${NONE} | | ... | ${dut2} | ${dut2_if1} | ${NONE} | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} | | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} | | Then Traffic should pass with no loss | ${duration} | ${rate} | | ... | ${framesize} | 3-node-IPv6