# Copyright (c) 2016 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Variables *** # Node and interface to run tests on. | ${node}= | ${nodes['DUT1']} | ${interface}= | ${node['interfaces'].values()[0]['name']} # Configuration which will be set and verified during tests. | @{ipv4_address}= | 192.168.0.2 | 255.255.255.0 | @{ipv4_neighbor}= | 192.168.0.3 | 08:00:27:c0:5d:37 | &{ipv4_settings}= | enabled=${True} | forwarding=${True} | mtu=9000 | @{ipv6_address}= | 10::10 | 64 | @{ipv6_neighbor}= | 10::11 | 08:00:27:c0:5d:37 | &{ipv6_settings}= | enabled=${True} | forwarding=${True} | mtu=9000 | ... | dup-addr-detect-transmits=5 | &{ethernet}= | mtu=9000 | &{routing}= | vrf-id=27 | &{vxlan_settings}= | src=10.0.1.20 | dst=10.0.3.20 | vni=1000 | ... | encap-vrf-id=1000 *** Settings *** | Resource | resources/libraries/robot/default.robot | Resource | resources/libraries/robot/honeycomb/honeycomb.robot | Resource | resources/libraries/robot/honeycomb/interfaces.robot | Suite Setup | Run keywords | Setup all DUTs before test | AND | ... | Setup Honeycomb service on DUTs | ${node} | Documentation | *Honeycomb interface management test suite.* | ... | ... | Test suite uses the first interface of the first DUT node. *** Test Cases *** | Honeycomb configures and reads interface state | | [Documentation] | Check if Honeycomb API can modify the admin state of\ | | ... | VPP interfaces. | | [Tags] | honeycomb_sanity | | Given Interface state is | ${node} | ${interface} | down | | When Honeycomb sets interface state | ${node} | ${interface} | up | | Then Interface state from Honeycomb should be | | ... | ${node} | ${interface} | up | | And Interface state from VAT should be | ${node} | ${interface} | up | | When Honeycomb sets interface state | ${node} | ${interface} | down | | Then Interface state from Honeycomb should be | | ... | ${node} | ${interface} | down | | And Interface state from VAT should be | ${node} | ${interface} | down | Honeycomb modifies interface configuration - ipv4 | | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4. | | [Tags] | honeycomb_sanity | | When Honeycomb sets interface ipv4 configuration | | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor} | | ... | ${ipv4_settings} | | Then IPv4 config from Honeycomb should be | | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor} | | ... | ${ipv4_settings} | | And IPv4 config from VAT should be | | ... | ${node} | ${interface} | @{ipv4_address} | Honeycomb modifies interface configuration - ipv6 | | [Documentation] | Check if Honeycomb API can configure interfaces for ipv6. | | [Tags] | honeycomb_sanity | | When Honeycomb sets interface ipv6 configuration | | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor} | | ... | ${ipv6_settings} | | Then IPv6 config from Honeycomb should be | | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor} | | ... | ${ipv6_settings} | | And IPv6 config from VAT should be | | ... | ${node} | ${interface} | @{ipv6_address} | Honeycomb modifies interface configuration - ethernet,routing | | [Documentation] | Check if Honeycomb API can configure interface ethernet\ | | ... | and routing settings. | | [Tags] | honeycomb_sanity | | When Honeycomb sets interface ethernet and routing configuration | | ... | ${node} | ${interface} | ${ethernet} | ${routing} | | Then Interface ethernet and routing configuration from Honeycomb should be | | ... | ${node} | ${interface} | ${ethernet} | ${routing} | | And Interface ethernet and routing configuration from VAT should be | | ... | ${node} | ${interface} | ${ethernet['mtu']} | ${routing['vrf-id']} | Honeycomb modifies interface configuration - VxLAN | | [Documentation] | Check if Honeycomb API can configure interface VxLAN \ | | ... | settings. | | [Tags] | honeycomb_sanity | | When Honeycomb sets interface VxLAN configuration | | ... | ${node} | ${interface} | &{vxlan_settings} | | Then VxLAN configuration from Honeycomb should be | | ... | ${node} | ${interface} | &{vxlan_settings} | | And VxLAN configuration from VAT should be | | ... | ${node} | ${interface} | &{vxlan_settings}