# Copyright (c) 2019 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/shared/default.robot | ... | Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY | ... | NIC_Virtual | IP4FWD | IPSEC | IPSECSW | IPSECTPT | IP4BASE | ... | AES_128_CBC | HMAC_SHA_512 | HMAC | AES | DRV_VFIO_PCI | ... | Suite Setup | Setup suite single link | scapy | Test Setup | Setup test | Test Teardown | Tear down test | packet_trace | ... | Test Template | Local Template | ... | Documentation | *IPv4 IPsec transport mode test suite.* | ... | ... | *[Top] Network topologies:* TG-DUT1 2-node topology with one link\ | ... | between nodes. | ... | *[Cfg] DUT configuration:* On DUT1 create loopback interface, configure\ | ... | loopback an physical interface IPv4 addresses, static ARP record, route\ | ... | and IPsec manual keyed connection in transport mode. | ... | *[Ver] TG verification:* ESP packet is sent from TG to DUT1. ESP packet\ | ... | is received on TG from DUT1. | ... | *[Ref] Applicable standard specifications:* RFC4303. *** Variables *** | @{plugins_to_enable}= | dpdk_plugin.so | crypto_ia32_plugin.so | ... | crypto_ipsecmb_plugin.so | crypto_openssl_plugin.so | ${crypto_type}= | ${None} | ${nic_name}= | virtual | ${nic_driver}= | vfio-pci | ${overhead}= | ${54} | ${tg_spi}= | ${1000} | ${dut_spi}= | ${1001} | ${ESP_PROTO}= | ${50} | ${tg_if_ip4}= | 192.168.100.2 | ${dut_if_ip4}= | 192.168.100.3 | ${tg_lo_ip4}= | 192.168.3.3 | ${dut_lo_ip4}= | 192.168.4.4 | ${ip4_plen}= | ${24} *** Keywords *** | Local Template | | [Documentation] | | ... | [Cfg] On DUT1 configure IPsec manual keyed connection with encryption\ | | ... | algorithm AES_128_CBC and integrity algorithm HMAC_SHA_512 in\ | | ... | transport mode. | | ... | | ... | *Arguments:* | | ... | - frame_size - Framesize in Bytes in integer. Type: integer | | ... | - phy_cores - Number of physical cores. Type: integer | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer | | ... | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} | | ... | | Set Test Variable | \${frame_size} | | ... | | # These are enums (not strings) so they cannot be in Variables table. | | ${encr_alg}= | Crypto Alg AES CBC 128 | | ${auth_alg}= | Integ Alg SHA 512 256 | | ... | | Given Set Max Rate And Jumbo | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} | | And Pre-initialize layer driver | ${nic_driver} | | And Apply startup configuration on all VPP DUTs | with_trace=${True} | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface | | And Configure topology for IPv4 IPsec testing | | And Generate keys for IPSec | ${encr_alg} | ${auth_alg} | | And Configure manual keyed connection for IPSec | | ... | ${dut1} | ${dut1_if1} | ${encr_alg} | ${encr_key} | ${auth_alg} | | ... | ${auth_key} | ${dut_spi} | ${tg_spi} | ${dut_tun_ip} | ${tg_tun_ip} | | Then Send IPsec Packet and verify ESP encapsulation in received packet | | ... | ${tg} | ${tg_if1} | ${dut1_if1_mac} | | ... | ${encr_alg} | ${encr_key} | ${auth_alg} | ${auth_key} | ${tg_spi} | | ... | ${dut_spi} | ${tg_tun_ip} | ${dut_tun_ip} *** Test Cases *** | tc01-110B-ethip4ipsec1tptsw-ip4base-policy-aes-128-cbc-sha-512-256-dev | | [Tags] | 110B | | frame_size=${110} | phy_cores=${0}