# Copyright (c) 2022 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/shared/default.robot | | Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY | ... | NIC_Intel-X710 | ETH | IP4FWD | BASE | IP4BASE | 1TAP | NAMESPACE | ... | DRV_VFIO_PCI | ... | RXQ_SIZE_0 | TXQ_SIZE_0 | ... | ethicmp4-ip4base-eth-1tap-namespace | | Suite Setup | Setup suite topology interfaces | scapy | Test Setup | Setup test | namespace | Test Teardown | Tear down test | packet_trace | telemetry | namespace | | Test Template | Local Template | | Documentation | **Tap Interface Traffic Tests** | ... | | ... | - **[Top] Network Topologies:** TG=DUT1 2-node topology with two links \ | ... | between nodes. | ... | | ... | - **[Enc] Packet Encapsulations:** Eth-IPv4-ICMPv4 for L2 switching of \ | ... | IPv4. | ... | | ... | - **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 \ | ... | bridge-domain (L2BD) MAC learning enabled; Split Horizon Groups (SHG) \ | ... | are set depending on test case; Namespaces (NM) \ | ... | are set on DUT1 with attached linux-TAP. | ... | | ... | - **[Ver] TG verification:** Test ICMPv4 Echo Request packets \ | ... | are sent by TG on link to DUT1; On receipt TG verifies packets \ | ... | for correctness and their IPv4 src-addr, dst-addr, and MAC addresses. | ... | | ... | - **[Ref] Applicable standard specifications:** *** Variables *** | @{plugins_to_enable}= | dpdk_plugin.so | perfmon_plugin.so | ${crypto_type}= | ${None} | ${nic_name}= | Intel-X710 | ${nic_driver}= | vfio-pci | ${nic_rxq_size}= | 0 | ${nic_txq_size}= | 0 | ${nic_pfs}= | 2 | ${nic_vfs}= | 0 | ${overhead}= | ${0} | ${tap1_VPP_ip}= | 16.0.10.1 | ${tap1_NM_ip}= | 16.0.10.2 | ${tap1_NM_mac}= | 02:00:00:00:00:02 | ${dut_ip_address}= | 192.168.0.1 | ${tg_ip_address}= | 192.168.0.2 | ${tg_ip_address_GW}= | 192.168.0.0 | ${prefix}= | 24 # Telemetry | ${telemetry_profile}= | vppctl_test_teardown *** Keywords *** | Local Template | | [Documentation] | | ... | - **[Cfg]** On DUT1 configure two interface addresses with IPv4 of \ | | ... | which one is TAP interface (dut_to_tg_if and TAP) and one is \ | | ... | linux-TAP in namespace. | | ... | - **[Ver]** Packet sent from TG gets to the destination and \ | | ... | ICMP-reply is received on TG. | | | | ... | *Arguments:* | | ... | - frame_size - Framesize in Bytes in integer. Type: integer | | ... | - phy_cores - Number of physical cores. Type: integer | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer | | | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} | | | | Set Test Variable | \${frame_size} | | | | Given Set Max Rate And Jumbo | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} | | And Pre-initialize layer driver | ${nic_driver} | | And Apply startup configuration on all VPP DUTs | with_trace=${True} | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface | | ${int1}= | And Add Tap Interface | ${dut1} | tap0 | | And VPP Interface Set IP Address | | ... | ${dut1} | ${int1} | ${tap1_VPP_ip} | ${prefix} | | And VPP Interface Set IP Address | | ... | ${dut1} | ${DUT1_${int}1}[0] | ${dut_ip_address} | ${prefix} | | And Set Interface State | ${dut1} | ${int1} | up | | And Create Namespace | ${dut1} | nmspace1 | | And Attach Interface To Namespace | ${dut1} | nmspace1 | tap0 | | And Set Linux Interface MAC | | ... | ${dut1} | tap0 | ${tap1_NM_mac} | nmspace1 | | And Set Linux Interface IP | | ... | ${dut1} | tap0 | ${tap1_NM_ip} | ${prefix} | nmspace1 | | And VPP Add IP Neighbor | | ... | ${dut1} | ${DUT1_${int}1}[0] | ${tg_ip_address} | ${TG_pf1_mac}[0] | | And VPP Add IP Neighbor | | ... | ${dut1} | ${int1} | ${tap1_NM_ip} | ${tap1_NM_mac} | | And Add Linux Route | | ... | ${dut1} | ${tg_ip_address_GW} | ${prefix} | ${tap1_VPP_ip} | nmspace1 | | Then Send ICMP echo request and verify answer | | ... | ${tg} | ${TG_pf1}[0] | ${DUT1_vf1_mac}[0] | ${TG_pf1_mac}[0] | | ... | ${tap1_NM_ip} | ${tg_ip_address} *** Test Cases *** | 64B-0c-ethicmp4-ip4base-eth-1tap-namespace-scapy | | [Tags] | 64B | 0C | | frame_size=${64} | phy_cores=${0}