# Copyright (c) 2018 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/performance/performance_setup.robot | Resource | resources/libraries/robot/crypto/ipsec.robot | ... | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR | ... | IP4FWD | IPSEC | IPSECSW | IPSECTUN | NIC_Intel-XL710 | BASE | ... | Suite Setup | Set up IPSec performance test suite | L3 | Intel-XL710 | ... | SW_cryptodev | Suite Teardown | Tear down 3-node performance topology | ... | Test Setup | Set up performance test | Test Teardown | Tear down performance mrr test | ... | Documentation | *Raw results IPv4 IPsec tunnel mode performance test suite.* | ... | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology | ... | with single links between nodes. | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn, | ... | Eth-IPv4-IPSec on DUT1-DUT2 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with DPDK SW | ... | crypto devices and multiple IPsec tunnels between them. | ... | DUTs get IPv4 traffic from TG, encrypt it | ... | and send to another DUT, where packets are decrypted and sent back to TG | ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic | ... | at line rate and reports total received/sent packets over trial period. | ... | Test packets are generated by TG on | ... | links to DUTs. TG traffic profile contains two L3 flow-groups | ... | (flow-group per direction, number of flows per flow-group equals to | ... | number of IPSec tunnels) with all packets | ... | containing Ethernet header, IPv4 header with IP protocol=61 and | ... | static payload. MAC addresses are matching MAC addresses of the TG | ... | node interfaces. Incrementing of IP.dst (IPv4 destination address) field | ... | is applied to both streams. | ... | *[Ref] Applicable standard specifications:* RFC4303 and RFC2544. *** Variables *** # XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps | ${s_24.5G}= | ${24500000000} # XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps | ${s_18.75Mpps}= | ${18750000} | ${tg_if1_ip4}= | 192.168.10.2 | ${dut1_if1_ip4}= | 192.168.10.1 | ${dut1_if2_ip4}= | 172.168.1.1 | ${dut2_if1_ip4}= | 172.168.1.2 | ${dut2_if2_ip4}= | 192.168.20.1 | ${tg_if2_ip4}= | 192.168.20.2 | ${raddr_ip4}= | 20.0.0.0 | ${laddr_ip4}= | 10.0.0.0 | ${addr_range}= | ${32} | ${ipsec_overhead}= | ${54} | ${n_tunnels}= | ${1} # Traffic profile: | ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${n_tunnels} *** Keywords *** | Check RR for IPv4 routing with IPSec SW cryptodev | | [Documentation] | | ... | [Cfg] DUT runs IPSec tunneling CBC-SHA1 config with ${wt} thread(s),\ | | ... | ${wt} phy core(s), ${rxq} receive queue(s) per NIC port. | | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ | | ... | trial throughput test. | | ... | | [Arguments] | ${framesize} | ${wt} | ${rxq} | | ... | | # Test Variables required for test teardown | | Set Test Variable | ${framesize} | | ${get_framesize}= | Get Frame Size | ${framesize} | | ${max_rate}= | Calculate pps | ${s_24.5G} | | ... | ${get_framesize} + ${ipsec_overhead} | | ${max_rate}= | Set Variable If | | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} | | ${encr_alg}= | Crypto Alg AES CBC 128 | | ${auth_alg}= | Integ Alg SHA1 96 | | ... | | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to all DUTs | | And Run Keyword If | ${get_framesize} < ${1522} | | ... | Add no multi seg to all DUTs | | And Add DPDK SW cryptodev on DUTs in 3-node single-link circular topology | | ... | aesni_mb | ${${wt}} | | And Add DPDK dev default RXD to all DUTs | 2048 | | And Add DPDK dev default TXD to all DUTs | 2048 | | And Apply startup configuration on all VPP DUTs | | When Generate keys for IPSec | ${encr_alg} | ${auth_alg} | | And Initialize IPSec in 3-node circular topology | | And VPP IPsec Create Tunnel Interfaces | | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2} | | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg} | | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range} | | And Set interfaces in path in 3-node circular topology up | | Then Traffic should pass with maximum rate | ${perf_trial_duration} | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} *** Test Cases *** | tc01-64B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 1 phy core, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ | | ... | throughput test. | | [Tags] | 64B | 1C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=${64} | wt=1 | rxq=1 | tc02-1518B-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 1 phy core, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\ | | ... | trial throughput test. | | [Tags] | 1518B | 1C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=${1518} | wt=1 | rxq=1 # TODO: Add check to make test fail if rx=0. # TODO: Add 9000B test cases when they start passing. | tc04-IMIX-1t1c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 1 phy core, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\ | | ... | trial throughput test. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | [Tags] | IMIX | 1C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=IMIX_v4_1 | wt=1 | rxq=1 | tc05-64B-2t2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 2 phy cores, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ | | ... | throughput test. | | [Tags] | 64B | 2C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=${64} | wt=2 | rxq=1 | tc06-1518B-2t2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 2 phy cores, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\ | | ... | trial throughput test. | | [Tags] | 1518B | 2C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=${1518} | wt=2 | rxq=1 | tc08-IMIX-2t2c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 2 phy cores, 1 receive queue per NIC port. | | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\ | | ... | trial throughput test. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | [Tags] | IMIX | 2C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=IMIX_v4_1 | wt=2 | rxq=1 | tc09-64B-4t4c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 4 phy cores, 2 receive queues per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ | | ... | throughput test. | | [Tags] | 64B | 4C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=${64} | wt=4 | rxq=2 | tc10-1518B-4t4c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 4 phy cores, 2 receive queues per NIC port. | | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\ | | ... | trial throughput test. | | [Tags] | 1518B | 4C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=${1518} | wt=4 | rxq=2 | tc12-IMIX-4t4c-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr | | [Documentation] | | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\ | | ... | with 4 phy cores, 2 receive queues per NIC port. | | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\ | | ... | trial throughput test. | | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) | | [Tags] | IMIX | 4C | | ... | | [Template] | Check RR for IPv4 routing with IPSec SW cryptodev | | framesize=IMIX_v4_1 | wt=4 | rxq=2