# Copyright (c) 2023 Cisco and/or its affiliates. # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at: # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. *** Settings *** | Resource | resources/libraries/robot/shared/default.robot | | Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR | ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS | ... | OACL | ACL10 | 100_FLOWS | DRV_VFIO_PCI | ... | RXQ_SIZE_0 | TXQ_SIZE_0 | ... | ethip4udp-ip4base-oacl10sl-100flows | | Suite Setup | Setup suite topology interfaces | performance | Suite Teardown | Tear down suite | performance | Test Setup | Setup test | performance | Test Teardown | Tear down test | performance | acl | | Test Template | Local Template | | Documentation | **RFC2544: Packet throughput IPv4 test cases with ACL** | ... | | ... | - **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular \ | ... | topology with single links between nodes. | ... | | ... | - **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for IPv4 routing. | ... | | ... | - **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4. \ | ... | routing and one static IPv4 /24 route entries. Required ACL rules are \ | ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are \ | ... | tested with ${nic_name}. | ... | | ... | - **[Ver] TG verification:** TG finds and reports throughput NDR (Non \ | ... | Drop Rate) with zero packet loss tolerance and throughput PDR \ | ... | (Partial Drop Rate) with non-zero packet loss tolerance (LT) \ | ... | expressed in percentage of packets transmitted. NDR and PDR are \ | ... | discovered for different Ethernet L2 frame sizes using MLRsearch \ | ... | library. | ... | Test packets are generated by TG on links to DUTs. TG traffic profile \ | ... | contains two L3 flow-groups (flow-group per direction, \ | ... | ${flows_per_dir} flows per flow-group) with all packets containing \ | ... | Ethernet header, IPv4 header with IP protocol=61 and static payload. \ | ... | MAC addresses are matching MAC addresses of the TG node interfaces. | ... | | ... | - **[Ref] Applicable standard specifications:** RFC2544. *** Variables *** | @{plugins_to_enable}= | dpdk_plugin.so | perfmon_plugin.so | acl_plugin.so | ${crypto_type}= | ${None} | ${nic_name}= | Intel-X710 | ${nic_driver}= | vfio-pci | ${nic_rxq_size}= | 0 | ${nic_txq_size}= | 0 | ${nic_pfs}= | 2 | ${nic_vfs}= | 0 | ${osi_layer}= | L3 | ${overhead}= | ${0} # ACL test setup | ${acl_action}= | permit | ${acl_apply_type}= | output | ${no_hit_aces_number}= | 10 | ${flows_per_dir}= | 100 | ${ip_nr}= | ${10} # starting points for non-hitting ACLs | ${src_ip_start}= | 30.30.30.1 | ${dst_ip_start}= | 40.40.40.1 | ${ip_step}= | ${1} | ${sport_start}= | ${1000} | ${dport_start}= | ${1000} | ${port_step}= | ${1} | ${trex_stream1_subnet}= | 10.10.10.0/24 | ${trex_stream2_subnet}= | 20.20.20.0/24 # Traffic profile | ${traffic_profile}= | trex-stl-ethip4udp-10u10p-conc *** Keywords *** | Local Template | | [Documentation] | | ... | - **[Cfg]** DUT runs IPv4 routing config. \ | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. | | ... | - **[Ver]** Measure NDR and PDR values using MLRsearch algorithm. | | | | ... | *Arguments:* | | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). | | ... | Type: integer, string | | ... | - phy_cores - Number of physical cores. Type: integer | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer | | | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} | | | | Set Test Variable | \${frame_size} | | | | Given Set Max Rate And Jumbo | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} | | And Pre-initialize layer driver | ${nic_driver} | | And Apply startup configuration on all VPP DUTs | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface | | And Initialize IPv4 routing with IPv4 ACLs on DUT1 in circular topology | | ... | ${ip_nr} | | Then Find NDR and PDR intervals using optimized search *** Test Cases *** | 64B-1c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 64B | 1C | | frame_size=${64} | phy_cores=${1} | 64B-2c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 64B | 2C | | frame_size=${64} | phy_cores=${2} | 64B-4c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 64B | 4C | | frame_size=${64} | phy_cores=${4} | 1518B-1c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 1518B | 1C | | frame_size=${1518} | phy_cores=${1} | 1518B-2c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 1518B | 2C | | frame_size=${1518} | phy_cores=${2} | 1518B-4c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 1518B | 4C | | frame_size=${1518} | phy_cores=${4} | 9000B-1c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 9000B | 1C | | frame_size=${9000} | phy_cores=${1} | 9000B-2c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 9000B | 2C | | frame_size=${9000} | phy_cores=${2} | 9000B-4c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | 9000B | 4C | | frame_size=${9000} | phy_cores=${4} | IMIX-1c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | IMIX | 1C | | frame_size=IMIX_v4_1 | phy_cores=${1} | IMIX-2c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | IMIX | 2C | | frame_size=IMIX_v4_1 | phy_cores=${2} | IMIX-4c-ethip4udp-ip4base-oacl10sl-100flows-ndrpdr | | [Tags] | IMIX | 4C | | frame_size=IMIX_v4_1 | phy_cores=${4}