CSIT-1197: Add Comparison Across Testbeds to the Report

[csit.git] / docs / report / honeycomb_functional_tests / overview.rst

diff --git a/docs/report/honeycomb_functional_tests/overview.rst b/docs/report/honeycomb_functional_tests/overview.rst
index 1c992a5..f67f735 100644 (file)
--- a/docs/report/honeycomb_functional_tests/overview.rst
+++ b/docs/report/honeycomb_functional_tests/overview.rst
@@ -5,13 +5,11 @@ Tested Virtual Topologies
 -------------------------
 
 CSIT Honeycomb functional tests are executed on virtualized topologies created
-using Virtual Internet Routing Lab (VIRL) simulation platform contributed by
-Cisco. VIRL runs on physical baremetal servers hosted by LF FD.io project. All
-tests are executed in two node logical test topology - Traffic Generator (TG)
-node and Systems Under Test (SUT1) node connected in a loop. Logical test
-topology is shown in the figure below.
-
-::
+using :abbr:`VIRL (Virtual Internet Routing Lab)` simulation platform
+contributed by Cisco. VIRL runs on physical baremetal servers hosted by LF FD.io
+project. All tests are executed in two node logical test topology - Traffic
+Generator (TG) node and Systems Under Test (SUT1) node connected in a loop.
+Logical test topology is shown in the figure below.::
 
                      +------------------------+
                      |                        |
@@ -48,7 +46,7 @@ for clarity).
 Functional Tests Coverage
 -------------------------
 
-The following Honeycomb functional test areas are included in the CSIT |release|
+The following Honeycomb functional test areas are included in the |csit-release|
 with results listed in this report:
 
 - **Basic interface management** - CRUD for interface state,
@@ -107,7 +105,12 @@ with results listed in this report:
   - Configure and delete Lisp mapping as local and remote.
   - Configure and delete Lisp adjacency mapping
   - Configure and delete Lisp map resolver, proxy ITR.
-  - Test case count: 16
+  - Test case count: 18
+- **LISP GPE** - CRUD for LISP GPE mappings.
+  - Toggle Lisp GPE feature status.
+  - Configure Lisp GPE mappings.
+  - Traffic test verifying encapsulation.
+  - Test case count: 12
 - **NAT** - CRD for NAT entries, interface assignment.
   - Configure and delete up to two NAT entries.
   - Assign NAT entries to a physical interface.
@@ -148,11 +151,17 @@ with results listed in this report:
   - Configure Policing rules.
   - Assign to interface.
   - Test case count: 6
+- **Border Gateway Protocol** - CRUD and functional tests for BGP.
+  - Configure peers and routes
+  - Check interactions with another BGP peer.
+  - Test case count: 13
 - **Honeycomb Infractructure** - configuration persistence,
   - Netconf notifications for interface events,
   - Netconf negative tests aimed at specific issues
+  - Netconf/Restconf northbound over IPv6
+  - Test case count: 12
 
-Total 173 Honeycomb functional tests in the CSIT |release|.
+Total 219 Honeycomb functional tests in the |csit-release|.
 
 Operational data in Honeycomb should mirror configuration data at all times.
 Because of this, test cases follow this general pattern:
@@ -170,7 +179,7 @@ the DUT node.
 Functional Tests Naming
 -----------------------
 
-CSIT |release| introduced a common structured naming convention for all
+CSIT-17.01 introduced a common structured naming convention for all
 performance and functional tests. This change was driven by substantially
 growing number and type of CSIT test cases. Firstly, the original practice did
 not always follow any strict naming convention. Secondly test names did not