Remove: VIRL

[csit.git] / resources / tools / disk-image-builder / centos / scripts-remote / serial-console-centos-7-1511.sh

diff --git a/resources/tools/disk-image-builder/centos/scripts-remote/serial-console-centos-7-1511.sh b/resources/tools/disk-image-builder/centos/scripts-remote/serial-console-centos-7-1511.sh
deleted file mode 100644 (file)
index 6107db9..0000000
--- a/resources/tools/disk-image-builder/centos/scripts-remote/serial-console-centos-7-1511.sh
+++ /dev/null
@@ -1,89 +0,0 @@
-#!/bin/sh -e
-
-# Copyright (c) 2017 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-##
-## Serial console
-##
-echo "********** CONFIGURING SERIAL CONSOLE **********"
-cat - > /etc/systemd/system/serial-getty-digi@.service <<"_EOF"
-# ttyS0 - getty
-#
-# This service maintains a getty on ttyS0 from the point the system is
-# started until it is shut down again.
-#  This file is part of systemd.
-#
-#  systemd is free software; you can redistribute it and/or modify it
-#  under the terms of the GNU Lesser General Public License as published by
-#  the Free Software Foundation; either version 2.1 of the License, or
-#  (at your option) any later version.
-
-[Unit]
-Description=Serial Getty on %I
-Documentation=man:agetty(8) man:systemd-getty-generator(8)
-Documentation=http://0pointer.de/blog/projects/serial-console.html
-BindsTo=dev-%i.device
-After=dev-%i.device systemd-user-sessions.service plymouth-quit-wait.service
-After=rc-local.service
-
-# If additional gettys are spawned during boot then we should make
-# sure that this is synchronized before getty.target, even though
-# getty.target didn't actually pull it in.
-Before=getty.target
-IgnoreOnIsolate=yes
-
-[Service]
-ExecStart=-/sbin/agetty -L %I 115200
-Type=idle
-Restart=always
-UtmpIdentifier=%I
-TTYPath=/dev/%I
-TTYReset=yes
-TTYVHangup=yes
-KillMode=process
-IgnoreSIGPIPE=no
-SendSIGHUP=yes
-
-[Install]
-WantedBy=getty.target
-_EOF
-
-cat - > /etc/default/grub <<"_EOF"
-# If you change this file, run 'update-grub' afterwards to update
-# /boot/grub/grub.cfg.
-# For full documentation of the options in this file, see:
-#   info -f grub -n 'Simple configuration'
-
-GRUB_DEFAULT=0
-GRUB_TIMEOUT=5
-GRUB_DISABLE_SUBMENU=true
-GRUB_DISTRIBUTOR="$(sed 's, release .*$,,g' /etc/system-release)"
-GRUB_CMDLINE_LINUX="rhgb quiet console=tty0 console=ttyS0,115200n8"
-
-GRUB_TERMINAL=serial
-GRUB_SERIAL_COMMAND="serial --speed=115200 --unit=0 --word=8 --parity=no --stop=1"
-
-# Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux
-#GRUB_DISABLE_LINUX_UUID=true
-
-# Uncomment to disable generation of recovery mode menu entries
-#GRUB_DISABLE_RECOVERY="true"
-
-# Uncomment to get a beep at grub start
-#GRUB_INIT_TUNE="480 440 1"
-_EOF
-
-grub2-mkconfig -o /boot/grub2/grub.cfg
-sudo systemctl enable serial-getty-digi@ttyS0.service
-sudo systemctl start serial-getty-digi@ttyS0.service