to as "PXE boostrap server" below), and that the directory containig this README
is available on the PXE bootstrap server in ~testuser/host-setup.
-### Prepare the PXE bootstrap server (one-time)
+### Prepare the PXE bootstrap server when there is no http server
- `sudo apt-get install isc-dhcp-server tftpd-hpa nginx-light ansible`
- edit dhcpd.conf and place it to /etc/dhcp/
- `sudo mkdir /mnt/cdrom`
- `sudo mount -o loop ubuntu-16.04.2-server-amd64.iso /mnt/cdrom/`
- `sudo cp -r /mnt/cdrom/install/netboot/* /var/lib/tftpboot/`
- - `sudo mkdir /usr/share/nginx/html/ubuntu`
- - `sudo cp -r /mnt/cdrom/* /usr/share/nginx/html/ubuntu/`
+ - figure out where nginx will look for files on the filesystem when
+ responding to HTTP requests. The configuration is in one of the
+ files in /etc/nginx/conf.d/, /etc/nginx/sites-enabled/ or in
+ /etc/nginx/nginx.conf under section server/root. Save the path to NGINX_ROOT
+ - `sudo mkdir -p ${NGINX_ROOT}/download/ubuntu`
+ - `sudo cp -r /mnt/cdrom/* ${NGINX_ROOT}/download/ubuntu/`
- `sudo cp /mnt/cdrom/ubuntu/isolinux/ldlinux.c32 /var/lib/tftpboot`
- `sudo cp /mnt/cdrom/ubuntu/isolinux/libcom32.c32 /var/lib/tftpboot`
- `sudo cp /mnt/cdrom/ubuntu/isolinux/libutil.c32 /var/lib/tftpboot`
- `sudo cp /mnt/cdrom/ubuntu/isolinux/chain.c32 /var/lib/tftpboot`
- `sudo umount /mnt/cdrom`
- edit ks.cfg and replace IP address with that of your PXE bootstrap server
- - `sudo cp ks.cfg /usr/share/nginx/html/ks.cfg`
+ - `sudo cp ks.cfg ${NGINX_ROOT}/download/ks.cfg`
- edit boot-screens_txt.cfg and replace IP address with that of your PXE bootstrap server
- `sudo cp boot-screens_txt.cfg /var/lib/tftpboot/ubuntu-installer/amd64/boot-screens/txt.cfg`
- `sudo cp syslinux.cfg /var/lib/tftpboot/ubuntu-installer/amd64/boot-screens/syslinux.cfg`
-### PREFERED: Prepare the PXE bootstrap server (alternative way without NGINX)
+### PREFERED: Prepare the PXE bootstrap server when an http server is already configured
- `sudo apt-get install isc-dhcp-server tftpd-hpa ansible`
- edit dhcpd.conf and place it to /etc/dhcp/
- set CIMC address
- set CIMC username, password and hostname
+- set IPMI address
+- set IPMI username, password and hostname
### Bootstrap the host
-From PXE boostrap server:
+Optional: From PXE boostrap server in case of installing Haswell
- - `cd ~testuser/host-setup/cimc`
+ - `cd resources/tools/testbed-setup/cimc`
- Initialize args.ip: Power-Off, reset BIOS defaults, Enable console redir, get LOM MAC addr
- `./cimc.py -u admin -p Cisco1234 $CIMC_ADDRESS -d -i`
- Adjust BIOS settings
- Reboot server with boot from PXE (restart immediately)
- `./cimc.py -u admin -p Cisco1234 $CIMC_ADDRESS -d -pxe`
-While Ubuntu install is running:
+Optional: If RAID is not created on Haswells. Execute while Ubuntu install is running
- create RAID array. Reboot if needed.
- `./cimc.py -u admin -p Cisco1234 $CIMC_ADDRESS -d --wipe`
- Set the next boot from HDD (without restart)
- `./cimc.py -u admin -p Cisco1234 $CIMC_ADDRESS -d -hdd`
-When installation is finished:
-
- - `ssh-copy-id 10.30.51.x`
- - `cd ~testuser/host-setup/playbooks`
- - edit /etc/ansible/hosts; add the hosts you are installing. *REMOVE ANY HOSTS YOU ARE NOT CURRENTLY INSTALLING*.
-
- Example for physical testbed hosts:
- ~~~
- [tg]
- 10.30.51.24 hostname=t3-tg1 isolcpus="1-17,19-35" ansible_python_interpreter=/usr/bin/python2.7
-
- [sut]
- 10.30.51.25 hostname=t3-sut1 isolcpus="1-17,19-35" ansible_python_interpreter=/usr/bin/python2.7
- 10.30.51.26 hostname=t3-sut2 isolcpus="1-17,19-35" ansible_python_interpreter=/usr/bin/python2.7
- ~~~
+Optional: If installing Skylake machine, connect to IPMI and boot from PXE via F12
- Example for VIRL hosts -- use the "virl" tag and specify the flat network start and end addresses:
-
- ~~~
- [virl]
- 10.30.51.28 hostname=t4-virl1 virl_l2_start=10.30.52.2 virl_l2_end=10.30.52.253 virl_l2_network=10.30.52.0/24 virl_l2_ip=10.30.52.254 virl_public_port=eth0
- ~~~
+When installation is finished:
- - `ansible-playbook --ask-sudo-pass 01-host-setup.yaml`
- - `ansible-playbook reboot.yaml`
+ - Copy ssh keys for no pass access: `ssh-copy-id 10.30.51.x`
+ - Clone CSIT actual repo: `git clone https://gerrit.fd.io/r/csit`
+ - Go to ansible directory: `cd csit/resources/tools/testbed-setup/ansible`
+ - Edit production file and uncomment servers that are supposed to be installed: `ansible-playbook --ask-become-pass --inventory production site.yaml --list-hosts`
+ - Run ansible on selected hosts: `ansible-playbook --ask-become-pass --inventory production site.yaml`
For non-VIRL hosts, stop here.
-
### VIRL installation
After the host has rebooted:
Code Review / csit.git / blobdiff