| ... | AND | Show Vpp Settings | ${nodes['DUT2']}
| ... | AND | Check VPP PID in Teardown
| ...
-| Documentation | *IPv4-ip4-ipsec-lispgpe-ip4 - main fib, vrf (gpe_vni-to-vrf)
+| Documentation | *IPv4-ip4-ipsec-lispgpe-ip4 - main fib, vrf (gpe_vni-to-vrf)*
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
*** Variables ***
| ${dut2_spi}= | ${1000}
| ${dut1_spi}= | ${1001}
+
| ${ESP_PROTO}= | ${50}
-| ${sock1}= | /tmp/sock1
-| ${sock2}= | /tmp/sock2
+
| ${bid}= | 10
*** Test Cases ***
| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac}
| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac}
-| TC05: DUT1 and DUT2 route IPv4 over Vhost to LISP GPE tunnel using IPsec (transport) on RLOC Int.
-| | [Documentation]
-| | ... | [Top] TG-DUT1-DUT2-TG.
-| | ... | [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMP on DUT1-DUT2, Eth-IPv4-ICMP\
-| | ... | on TG-DUTn.
-| | ... | [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with\
-| | ... | IPsec in between DUTS. Create Qemu vm on DUT1 and configure bridge\
-| | ... | between two vhosts.
-| | ... | [Ver] Case: ip4-ipsec-lispgpe-ip4 - main fib, virt2lisp\
-| | ... | Make TG send ICMPv4 Echo Req between its interfaces across\
-| | ... | both DUTs and LISP GPE tunnel between them; verify IPv4 headers on\
-| | ... | received packets are correct.
-| | ... | [Ref] RFC6830, RFC4303.
-| | [Teardown] | Run Keywords | Show Packet Trace on All DUTs | ${nodes}
-| | ... | AND | Show vpp trace dump on all DUTs
-| | ... | AND | Stop and Clear QEMU | ${dut1_node} | ${vm_node}
-| | ... | AND | Show VPP Settings | ${dut1_node}
-| | ... | AND | Show VPP Settings | ${dut2_node}
-| | ... | AND | Check VPP PID in Teardown
-| | ...
-| | ${encr_alg}= | Crypto Alg AES CBC 128
-| | ${auth_alg}= | Integ Alg SHA1 96
-| | Given Setup 3-node Topology
-| | And Add IP Neighbors
-| | And Setup Qemu DUT1
-| | And Set up LISP GPE topology
-| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE}
-| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
-| | ... | ${dut1_to_dut2_ip4_static_adjacency}
-| | ... | ${dut2_to_dut1_ip4_static_adjacency}
-| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
-| | When VPP Setup IPsec Manual Keyed Connection
-| | ... | ${dut1_node} | ${dut1_to_dut2} | ${encr_alg} | ${encr_key}
-| | ... | ${auth_alg} | ${auth_key} | ${dut1_spi} | ${dut2_spi}
-| | ... | ${dut1_to_dut2_ip4} | ${dut2_to_dut1_ip4}
-| | And VPP Setup IPsec Manual Keyed Connection
-| | ... | ${dut2_node} | ${dut2_to_dut1} | ${encr_alg} | ${encr_key}
-| | ... | ${auth_alg} | ${auth_key} | ${dut2_spi} | ${dut1_spi}
-| | ... | ${dut2_to_dut1_ip4} | ${dut1_to_dut2_ip4}
-| | Then Send Packet And Check Headers
-| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4}
-| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dst_vhost_mac}
-| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac}
-| | And Send Packet And Check Headers
-| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4}
-| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac}
-| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac}
-
-| TC06: DUT1 and DUT2 route IPv4 over Vhost to LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int.
-| | [Documentation]
-| | ... | [Top] TG-DUT1-DUT2-TG.
-| | ... | [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2,\
-| | ... | Eth-IPv4-ICMPv4 on TG-DUTn.
-| | ... | [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with\
-| | ... | IPsec in between DUTS.
-| | ... | [Ver] Case: ip4-ipsec-lispgpe-ip4 - main fib, virt2lisp\
-| | ... | Make TG send ICMPv4 Echo Req between its interfaces across\
-| | ... | both DUTs and LISP GPE tunnel between them; verify IPv4 headers on\
-| | ... | received packets are correct.
-| | ... | [Ref] RFC6830, RFC4303.
-| | [Teardown] | Run Keywords | Show Packet Trace on All DUTs | ${nodes}
-| | ... | AND | Show vpp trace dump on all DUTs
-| | ... | AND | Stop and Clear QEMU | ${dut1_node} | ${vm_node}
-| | ... | AND | Show VPP Settings | ${dut1_node}
-| | ... | AND | Show VPP Settings | ${dut2_node}
-| | ... | AND | Check VPP PID in Teardown
-| | ...
-| | ${encr_alg}= | Crypto Alg AES CBC 128
-| | ${auth_alg}= | Integ Alg SHA1 96
-| | Given Setup 3-node Topology
-| | And Add IP Neighbors
-| | And Setup Qemu DUT1
-| | And Set up LISP GPE topology
-| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE}
-| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE}
-| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
-| | ... | ${dut1_to_dut2_ip4_static_adjacency}
-| | ... | ${dut2_to_dut1_ip4_static_adjacency}
-| | ${lisp1_if_idx}= | resources.libraries.python.InterfaceUtil.Get Sw If Index
-| | ... | ${dut1_node} | lisp_gpe0
-| | ${lisp2_if_idx}= | resources.libraries.python.InterfaceUtil.Get Sw If Index
-| | ... | ${dut2_node} | lisp_gpe0
-| | And IPsec Generate Keys | ${encr_alg} | ${auth_alg}
-| | When VPP Setup IPsec Manual Keyed Connection
-| | ... | ${dut1_node} | ${lisp1_if_idx} | ${encr_alg} | ${encr_key}
-| | ... | ${auth_alg} | ${auth_key} | ${dut1_spi} | ${dut2_spi}
-| | ... | ${dut1_to_dut2_ip4} | ${dut2_to_dut1_ip4}
-| | And VPP Setup IPsec Manual Keyed Connection
-| | ... | ${dut2_node} | ${lisp2_if_idx} | ${encr_alg} | ${encr_key}
-| | ... | ${auth_alg} | ${auth_key} | ${dut2_spi} | ${dut1_spi}
-| | ... | ${dut2_to_dut1_ip4} | ${dut1_to_dut2_ip4}
-| | Then Send Packet And Check Headers
-| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4}
-| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dst_vhost_mac}
-| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac}
-| | And Send Packet And Check Headers
-| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4}
-| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac}
-| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac}
-
*** Keywords ***
| Setup 3-node Topology
| | [Documentation]
| | ... | ${dut2_to_dut1_mac}
| | Add IP Neighbor | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4}
| | ... | ${dut1_to_dut2_mac}
-
-| Setup Qemu DUT1
-| | [Documentation] | Setup Vhosts on DUT1 and setup IP to one of them. Setup \
-| | ... | Qemu and bridge the vhosts.
-| | ${vhost1}= | And Vpp Create Vhost User Interface | ${dut1_node} | ${sock1}
-| | ${vhost2}= | And Vpp Create Vhost User Interface | ${dut1_node} | ${sock2}
-| | Set Interface Address | ${dut1_node} | ${vhost2} | 6.6.1.9
-| | ... | ${prefix4}
-| | Set Interface State | ${dut1_node} | ${vhost1} | up
-| | Set Interface State | ${dut1_node} | ${vhost2} | up
-| | Bridge domain on DUT node is created | ${dut1_node} | ${bid} | learn=${TRUE}
-| | Interface is added to bridge domain | ${dut1_node}
-| | ... | ${dut1_to_tg} | ${bid} | 0
-| | Interface is added to bridge domain | ${dut1_node}
-| | ... | ${vhost1} | ${bid} | 0
-| | ${vhost_mac}= | Get Vhost User Mac By SW Index | ${dut1_node} | ${vhost2}
-| | Set test variable | ${dst_vhost_mac} | ${vhost_mac}
-| | VM for Vhost L2BD forwarding is setup | ${dut1_node} | ${sock1} | ${sock2}
Code Review / csit.git / blobdiff