| ... | L3 | Intel-X520-DA2
| Suite Teardown | 3-node Performance Suite Teardown
| Test Setup | Setup all DUTs before test
-| Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs
-| Documentation | Minimal throughput acceptance test cases
+| Test Teardown | Run Keywords | Remove startup configuration of VPP from all DUTs
+| ... | AND | Show vpp trace dump on all DUTs
+| Documentation | *Reference NDR throughput IPv6 whitelist verify test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
+| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist
+| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
+| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In short performance tests, TG verifies
+| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet
+| ... | loss tolerance. Ref-NDR value is periodically updated acording to
+| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long
+| ... | performance tests for the same DUT confiiguration. Test packets are
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
+| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with
+| ... | all packets containing Ethernet header, IPv6 header and generated
+| ... | payload.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Test Cases ***
-| 1core VPP passes 78B frames through IPv6 forwarding with COP at 2x 2.9Mpps in 3-node topology
+| TC01: Verify 78B ref-NDR at 2x 2.8Mpps - DUT IPv6 whitelist - 1thread 1core 1rxq
| | [Documentation]
-| | ... | VPP with 1 core should pass 78B frames through IPv6 forwarding
-| | ... | at 2x 2.9Mpps in 3-node topology with COP.
-| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 78 Byte frames using single trial throughput test.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
| | ${framesize}= | Set Variable | 78
| | ${duration}= | Set Variable | 10
-| | ${rate}= | Set Variable | 2.9mpps
-| | Given Add '1' worker threads and rss '1' without HTT to all DUTs
+| | ${rate}= | Set Variable | 2.8mpps
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 1core VPP passes 1518B frames through IPv6 forwarding with COP at 2x 812,743pps in 3-node topology
+| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 1thread 1core 1rxq
| | [Documentation]
-| | ... | VPP with 1 core should pass 1518B frames through IPv6 forwarding
-| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology with COP.
-| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
| | ${framesize}= | Set Variable | 1518
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 812743pps
-| | Given Add '1' worker threads and rss '1' without HTT to all DUTs
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 1core VPP passes 9000B frames through IPv6 forwarding with COP at 2x 138,580pps in 3-node topology
+| TC03: Verify 9000B ref-NDR at 2x 138.580kpps - DUT IPv6 whitelist - 1thread 1core 1rxq
| | [Documentation]
-| | ... | VPP with 1 core should pass 9000B frames through IPv6 forwarding
-| | ... | at 2x138,580pps (2x 10Gbps) in 3-node topology with COP.
-| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
| | ${framesize}= | Set Variable | 9000
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 138580pps
-| | Given Add '1' worker threads and rss '1' without HTT to all DUTs
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When IPv6 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 2core VPP with rss 1 passes 78B frames through IPv6 forwarding with COP at 2x 4.9Mpps in 3-node topology
+| TC04: Verify 78B ref-NDR at 2x 4.9Mpps - DUT IPv6 whitelist - 2thread 2core 1rxq
| | [Documentation]
-| | ... | VPP with 2 cores should pass 78B frames through IPv6 forwarding
-| | ... | at 2x 4.9Mpps in 3-node topology with COP.
-| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 78 Byte frames using single trial throughput test.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 78
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 4.9mpps
-| | Given Add '2' worker threads and rss '1' without HTT to all DUTs
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 2core VPP with rss 1 passes 1518B frames through IPv6 forwarding with COP at 2x 812,743pps in 3-node topology
+| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 2thread 2core 1rxq
| | [Documentation]
-| | ... | VPP with 2 cores should pass 1518B frames through IPv6 forwarding
-| | ... | at 2x 812,743pps (2x 10Gbps) in 3-node topology with COP.
-| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 1518
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 812743pps
-| | Given Add '2' worker threads and rss '1' without HTT to all DUTs
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 2core VPP with rss 1 passes 9000B frames through IPv6 forwarding with COP at 2x 138,580pps in 3-node topology
+| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 whitelist - 2thread 2core 1rxq
| | [Documentation]
-| | ... | VPP with 2 cores should pass 9000B frames through IPv6 forwarding
-| | ... | at 2x 138,580pps (2x 10Gbps) in 3-node topology with COP.
-| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 9000
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 138580pps
-| | Given Add '2' worker threads and rss '1' without HTT to all DUTs
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When IPv6 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 4core VPP with rss 2 passes 78B frames through IPv6 forwarding with COP at 2x 10.1Mpps in 3-node topology
+| TC07: Verify 78B ref-NDR at 2x 10.1Mpps - DUT IPv6 whitelist - 4thread 4core 2rxq
| | [Documentation]
-| | ... | VPP with 4 cores and rss 2 should pass 78B frames through IPv6
-| | ... | forwarding at 2x 10.1Mpps in 3-node topology with COP.
-| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 78 Byte frames using single trial throughput test.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 78
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 10.1mpps
-| | Given Add '4' worker threads and rss '2' without HTT to all DUTs
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 4core VPP with rss 2 passes 1518B frames through IPv6 forwarding with COP at 2x 812,743pps in 3-node topology
+| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 4thread 4core 2rxq
| | [Documentation]
-| | ... | VPP with 4 cores and rss 2 should pass 1518B frames through IPv6
-| | ... | forwarding at 2x 812,743pps (2x 10Gbps) in 3-node topology with COP.
-| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 1518
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 812743pps
-| | Given Add '4' worker threads and rss '2' without HTT to all DUTs
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv6
-| 4core VPP with rss 2 passes 9000B frames through IPv6 forwarding with COP at 2x 138,580pps in 3-node topology
+| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 whitelist - 4thread 4core 2rxq
| | [Documentation]
-| | ... | VPP with 4 cores and rss 2 should pass 9000B frames through IPv6
-| | ... | forwarding at 2x 138,580pps (2x 10Gbps) in 3-node topology with COP.
-| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 9000
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 138580pps
-| | Given Add '4' worker threads and rss '2' without HTT to all DUTs
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When IPv6 forwarding initialized in a 3-node circular topology
Code Review / csit.git / blobdiff