CSIT-220: Rename directories in tests directory

[csit.git] / tests / suites / vlan / qinq_l2_xconnect.robot

diff --git a/tests/suites/vlan/qinq_l2_xconnect.robot b/tests/suites/vlan/qinq_l2_xconnect.robot
deleted file mode 100644 (file)
index 35fdcde..0000000
--- a/tests/suites/vlan/qinq_l2_xconnect.robot
+++ /dev/null
@@ -1,71 +0,0 @@
-# Copyright (c) 2016 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/default.robot
-| Resource | resources/libraries/robot/testing_path.robot
-| Resource | resources/libraries/robot/tagging.robot
-| Resource | resources/libraries/robot/l2_traffic.robot
-| Library  | resources.libraries.python.Trace
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV
-| Test Setup | Setup all DUTs before test
-| Suite Setup | Setup all TGs before traffic script
-| Test Teardown | Run Keywords | Show Packet Trace on All DUTs | ${nodes}
-| ...           | AND          | Show vpp trace dump on all DUTs
-| Documentation | *L2 cross-connect with QinQ test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology with
-| ... | single links between nodes.
-| ... | *[Enc] Packet encapsulations:* Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2,
-| ... | Eth-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2
-| ... | cross-connect (L2XC) switching with 802.1ad QinQ VLAN tag push and pop.
-| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are
-| ... | sent in both directions by TG on links to DUT1 and DUT2; on receive TG
-| ... | verifies packets for correctness and their IPv4 src-addr, dst-addr and
-| ... | MAC addresses.
-| ... | *[Ref] Applicable standard specifications:* IEEE 802.1ad.
-
-*** Variables ***
-| ${subid}= | 10
-| ${outer_vlan_id}= | 100
-| ${inner_vlan_id}= | 200
-| ${type_subif}= | two_tags
-| ${tag_rewrite_method}= | pop-2
-
-*** Test Cases ***
-| TC01: DUT1 and DUT2 with L2XC and two VLAN push-pop switch ICMPv4 between two TG links
-| | [Documentation]
-| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on \
-| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2
-| | ... | configure L2 cross-connect (L2XC), each with one interface to TG
-| | ... | and one Ethernet interface towards the other DUT; each DUT
-| | ... | pushes two VLAN tags on packets received from local TG, and
-| | ... | popping two VLAN tags on packets transmitted to local TG. [Ver]
-| | ... | Make TG send ICMPv4 Echo Req in both directions between two of
-| | ... | its interfaces to be switched by DUT1 and DUT2; verify all
-| | ... | packets are received. [Ref] IEEE 802.1ad.
-| | Given Path for 3-node testing is set
-| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']}
-| | And Interfaces in 3-node path are up
-| | When VLAN subinterfaces initialized on 3-node topology
-| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut2_node} | ${dut2_to_dut1} | ${subid}
-| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif}
-| | And L2 tag rewrite method setup on interfaces
-| | ... | ${dut1_node} | ${subif_index_1} | ${dut2_node} | ${subif_index_2}
-| | ... | ${tag_rewrite_method}
-| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect
-| | ... | ${dut1_node} | ${dut1_to_tg} | ${subif_index_1}
-| | ... | ${dut2_node} | ${dut2_to_tg} | ${subif_index_2}
-| | Then Send and receive ICMP Packet
-| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2}