+++ /dev/null
-# Copyright (c) 2019 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-# http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/shared/default.robot
-| ...
-| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY
-| ... | NIC_Virtual | ETH | IP4FWD | BASE | IP4BASE | TAP
-| ...
-| Suite Setup | Setup suite single link | scapy
-| Test Setup | Setup test | namespace
-| Test Teardown | Tear down test | packet_trace | namespace
-| ...
-| Documentation | *Tap Interface Traffic Tests*
-| ... | *[Top] Network Topologies:* TG=DUT1 2-node topology with two links
-| ... | between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-ICMPv4 for L2 switching of
-| ... | IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2
-| ... | bridge-domain (L2BD) MAC learning enabled; Split Horizon Groups (SHG)
-| ... | are set depending on test case; Namespaces (NM)
-| ... | are set on DUT1 with attached linux-TAP.
-| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets
-| ... | are sent by TG on link to DUT1; On receipt TG verifies packets
-| ... | for correctness and their IPv4 src-addr, dst-addr, and MAC addresses.
-| ... | *[Ref] Applicable standard specifications:*
-
-*** Variables ***
-| @{plugins_to_enable}= | dpdk_plugin.so
-| ${nic_name}= | virtual
-| ${overhead}= | ${0}
-| ${tap1_VPP_ip}= | 16.0.10.1
-| ${tap1_NM_ip}= | 16.0.10.2
-| ${tap1_NM_mac}= | 02:00:00:00:00:02
-| ${dut_ip_address}= | 192.168.0.1
-| ${tg_ip_address}= | 192.168.0.2
-| ${tg_ip_address_GW}= | 192.168.0.0
-| ${prefix}= | 24
-
-*** Test Cases ***
-| tc01-eth2p-ethicmpv4-ip4base-dev_tap-no-namespace
-| | [Documentation]
-| | ... | [Cfg] On DUT1 configure two interface addresses with IPv4 of which\
-| | ... | one is TAP interface (dut_to_tg_if and TAP) and one is linux-TAP.
-| | ... | [Ver] Packet sent from TG gets to the destination and ICMP-reply is\
-| | ... | received on TG.
-| | ...
-| | Set Test Variable | ${frame_size} | ${42}
-| | Set Test Variable | ${rxq_count_int} | ${1}
-| | ...
-| | Given Add PCI devices to all DUTs
-| | And Set Max Rate And Jumbo And Handle Multi Seg
-| | And Apply startup configuration on all VPP DUTs
-| | And VPP Enable Traces On All Duts | ${nodes}
-| | When Set interfaces in path up
-| | ${int1}= | And Add Tap Interface | ${dut1} | tap0
-| | And VPP Interface Set IP Address
-| | ... | ${dut1} | ${int1} | ${tap1_VPP_ip} | ${prefix}
-| | And VPP Interface Set IP Address
-| | ... | ${dut1} | ${dut1_if1} | ${dut_ip_address} | ${prefix}
-| | And Set Interface State | ${dut1} | ${int1} | up
-| | And Set Linux Interface MAC | ${dut1} | tap0 | ${tap1_NM_mac}
-| | And Set Linux Interface IP | ${dut1} | tap0 | ${tap1_NM_ip} | ${prefix}
-| | And Add Linux Route
-| | ... | ${dut1} | ${tg_ip_address_GW} | ${prefix} | ${tap1_VPP_ip}
-| | And VPP Add IP Neighbor
-| | ... | ${dut1} | ${dut1_if1} | ${tg_ip_address} | ${tg_if1_mac}
-| | And VPP Add IP Neighbor
-| | ... | ${dut1} | ${int1} | ${tap1_NM_ip} | ${tap1_NM_mac}
-| | Then Send ICMP echo request and verify answer
-| | ... | ${tg} | ${tg_if1} | ${dut1_if1_mac} | ${tg_if1_mac}
-| | ... | ${tap1_NM_ip} | ${tg_ip_address}
-
-| tc02-eth2p-ethicmpv4-ip4base-dev_tap-namespace
-| | [Documentation]
-| | ... | [Cfg] On DUT1 configure two interface addresses with IPv4 of which\
-| | ... | one is TAP interface (dut_to_tg_if and TAP) and one is linux-TAP in\
-| | ... | namespace.
-| | ... | [Ver] Packet sent from TG gets to the destination and ICMP-reply is\
-| | ... | received on TG.
-| | ...
-| | Set Test Variable | ${frame_size} | ${42}
-| | Set Test Variable | ${rxq_count_int} | ${1}
-| | ...
-| | Given Add PCI devices to all DUTs
-| | And Set Max Rate And Jumbo And Handle Multi Seg
-| | And Apply startup configuration on all VPP DUTs
-| | And VPP Enable Traces On All Duts | ${nodes}
-| | When Set interfaces in path up
-| | ${int1}= | And Add Tap Interface | ${dut1} | tap0
-| | And VPP Interface Set IP Address
-| | ... | ${dut1} | ${int1} | ${tap1_VPP_ip} | ${prefix}
-| | And VPP Interface Set IP Address
-| | ... | ${dut1} | ${dut1_if1} | ${dut_ip_address} | ${prefix}
-| | And Set Interface State | ${dut1} | ${int1} | up
-| | And Create Namespace | ${dut1} | nmspace1
-| | And Attach Interface To Namespace | ${dut1} | nmspace1 | tap0
-| | And Set Linux Interface MAC
-| | ... | ${dut1} | tap0 | ${tap1_NM_mac} | nmspace1
-| | And Set Linux Interface IP
-| | ... | ${dut1} | tap0 | ${tap1_NM_ip} | ${prefix} | nmspace1
-| | And VPP Add IP Neighbor
-| | ... | ${dut1} | ${dut1_if1} | ${tg_ip_address} | ${tg_if1_mac}
-| | And VPP Add IP Neighbor
-| | ... | ${dut1} | ${int1} | ${tap1_NM_ip} | ${tap1_NM_mac}
-| | And Add Linux Route
-| | ... | ${dut1} | ${tg_ip_address_GW} | ${prefix} | ${tap1_VPP_ip} | nmspace1
-| | Then Send ICMP echo request and verify answer
-| | ... | ${tg} | ${tg_if1} | ${dut1_if1_mac} | ${tg_if1_mac}
-| | ... | ${tap1_NM_ip} | ${tg_ip_address}
Code Review / csit.git / blobdiff