PLRsearch: Initial implementation and suites

[csit.git] / tests / vpp / perf / ip4 / 2n1l-25ge2p1xxv710-ethip4-ip4base-soak.robot

diff --git a/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4base-soak.robot b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4base-soak.robot
new file mode 100644 (file)
index 0000000..71bd645
--- /dev/null
+++ b/tests/vpp/perf/ip4/2n1l-25ge2p1xxv710-ethip4-ip4base-soak.robot
@@ -0,0 +1,74 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | SOAK
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | BASE | IP4BASE
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 routing test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4
+| ... | routing and two static IPv4 /24 route entries. DUT1 tested with
+| ... | 2p25GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* Perform PLRsearch to find critical load.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.\
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Perform PLRsearch to find critical load.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... |   Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | Then Find critical load using PLRsearch
+| | ... | ${framesize} | ${traffic_profile} | ${10000} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-soak
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}