CSIT-687: Directory structure reorganization

[csit.git] / tests / vpp / perf / ip6_tunnels / 10ge2p1x520-ethip6lispip6-ip6base-ndrpdrdisc.robot

diff --git a/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip6-ip6base-ndrpdrdisc.robot b/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip6-ip6base-ndrpdrdisc.robot
new file mode 100644 (file)
index 0000000..f29f4e4
--- /dev/null
+++ b/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip6-ip6base-ndrpdrdisc.robot
@@ -0,0 +1,596 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot
+| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | IP6FWD | ENCAP | LISP | IP6UNRLAY | IP6OVRLAY
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *RFC6830: Pkt throughput Lisp test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv6-LISP-IPv6 on DUT1-DUT2,\
+| ... | Eth-IPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\
+| ... | routing and static routes. LISPoIPv6 tunnel is configured between\
+| ... | DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic\
+| ... | by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | *[Ref] Applicable standard specifications:* RFC6830.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit} | ${10000000000}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253
+
+*** Test Cases ***
+| tc01-78B-1t1c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc02-78B-1t1c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc03-1460B-1t1c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 1460B | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${1460}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc04-1460B-1t1c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1460B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1460}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc05-9000B-1t1c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc06-9000B-1t1c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc07-78B-2t2c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc08-78B-2t2c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc09-1460B-2t2c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 1460B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1460}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc10-1460B-2t2c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1460B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1460}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc11-9000B-2t2c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc12-9000B-2t2c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc13-78B-4t4c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc14-78B-4t4c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${78}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc15-1460B-4t4c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 1460B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1460}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc16-1460B-4t4c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1460B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1460}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+| tc17-9000B-4t4c-ethip6lispip6-ip6base-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| tc18-9000B-4t4c-ethip6lispip6-ip6base-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize LISP IPv6 forwarding in 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Configure LISP topology in 3-node circular topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}