Remove lbdpdk perf tests

[csit.git] / tests / vpp / perf / l2 / 10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot

diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot
index 6613cb1..b342571 100644 (file)
--- a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.robot
@@ -28,23 +28,22 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *Raw results L2BD test cases with 802.1q test cases*
+| Documentation | *Raw results L2BD with IEEE 802.1Q test cases*
 | ...
 | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.\
-| ... | 802.1q tagging is applied on link between DUT1 and DUT2.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\
-| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC
-| ... | X520 Niantic by Intel.
+| ... | domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE\
+| ... | NIC X520 Niantic by Intel.
 | ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
 | ... | at line rate and reports total received/sent packets over trial period.\
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 254 flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses are matching MAC addresses of the TG node\
-| ... | interfaces.
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
@@ -62,8 +61,8 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2BD config with VLAN.
-| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
 | | ... | trial throughput test.
 | | ...
@@ -80,7 +79,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in a 3-node circular topology
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
 | | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}