Create l2bdscale tests for 2-node topology

[csit.git] / tests / vpp / perf / l2 / 10ge2p1x520-eth-l2bdscale1mmaclrn-mrr.robot

diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdscale1mmaclrn-mrr.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdscale1mmaclrn-mrr.robot
index 5846d5b..eae700a 100644 (file)
--- a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdscale1mmaclrn-mrr.robot
+++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdscale1mmaclrn-mrr.robot
@@ -34,32 +34,32 @@
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
 | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\
-| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI
+| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC\
 | ... | X520 Niantic by Intel.
 | ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
 | ... | at line rate and reports total received/sent packets over trial period.\
-| ... | Test packets are generated by TG on\
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 500k flows per flow-group) with all packets\
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
-| ... | payload. MAC addresses ranges are incremented as follows:
-| ... | port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f,\
-| ... | port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f,\
-| ... | port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f,\
-| ... | port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f,\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 500k flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload.\
+| ... | MAC addresses ranges are incremented as follows:
+| ... | port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f,
+| ... | port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f,
+| ... | port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f,
+| ... | port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
 # X520-DA2 bandwidth limit
-| ${s_limit} | ${10000000000}
+| ${s_limit}= | ${10000000000}
 # Traffic profile:
-| ${traffic_profile} | trex-sl-3n-ethip4-macsrc500kdst500k
+| ${traffic_profile}= | trex-sl-3n-ethip4-macsrc500kdst500k
 
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2BD config with ${phy_cores} phy
-| | ... | core(s).
+| | ... | [Cfg] Each DUT runs L2BD switching config and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
 | | ... | trial throughput test.
 | | ...
@@ -76,7 +76,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domain in 3-node circular topology
+| | When Initialize L2 bridge domain in circular topology
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}