CSIT-1205 Create AVF driver test - Add Tests L2BD L2XC

[csit.git] / tests / vpp / perf / l2 / 10ge2p1x710-avf-eth-l2xcbase-ndrpdr.robot

diff --git a/tests/vpp/perf/l2/10ge2p1x710-avf-eth-l2xcbase-ndrpdr.robot b/tests/vpp/perf/l2/10ge2p1x710-avf-eth-l2xcbase-ndrpdr.robot
new file mode 100644 (file)
index 0000000..c55843f
--- /dev/null
+++ b/tests/vpp/perf/l2/10ge2p1x710-avf-eth-l2xcbase-ndrpdr.robot
@@ -0,0 +1,123 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | L2XCFWD | BASE | L2XCBASE | DRV_AVF
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up SRIOV 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X710 | AVF
+| ... | AND | Set up performance test suite with AVF driver
+| ...
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local template
+| ...
+| Documentation | *RFC2544: Pkt throughput L2XC test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross-connect.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross-\
+| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF\
+| ... | enabled.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254
+
+*** Keywords ***
+| Local template
+| | [Documentation]
+| | ... | [Cfg] DUT runs L2XC config with ${phy_cores} phy
+| | ... | core(s).
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${20000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add DPDK no PCI to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize AVF interfaces
+| | And Initialize L2 xconnect in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-1518B-1c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc04-IMIX-1c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc05-64B-2c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc06-1518B-2c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc08-IMIX-2c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc09-64B-4c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc10-1518B-4c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc12-IMIX-4c-avf-eth-l2xcbase-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}